Lucci LEDlux Smith User manual

Installation Instructions
1 | P a g e v 1 . 1 ( 0 9 / 2 0 2 0 )
SMITH LED TABLE LAMP
SKU# 269391, 269392, 269393
Rated Voltage 12V 2A
Thank you for purchasing this quality Lucci product. To ensure correct function and safety, please read and follow all
instructions carefully before assembly, installation and use of this luminaire. Please keep instructions for future reference.
Warranty
•This portable luminaire is covered by a 3-year warranty valid for in-store replacement or refund only.
•The warranty period starts from the date of purchase. Please retain the proof of purchase.
•Warranty will be void if there is any damage due to improper usage or modification to the portable luminaire.
•Failure to comply with the instructions in this manual may increase the risk of damage or injury and will void the warranty.
Installation Requirements
•Select a suitable location for the portable luminaire:
- Ensure it is on a flat and stable surface.
- This portable luminaire is suitable for indoor use only.
- Do not place flammable material near or over the portable luminaire.
- Ensure the portable luminaire is not installed in direct line of an air vent/system.
- If the portable luminaire is placed in an area prone to moisture, ensure that the area is well ventilated, and an
appropriately rated exhaust fan is used if required. Damage or corrosion caused by moisture is not a product
fault, and as such is not covered under warranty.
•Only use the supplied plug in LED driver with this luminaire.
•Take care not to pull any electrical wires during unpacking as this may damage the connection.
•Lay out all the components on a smooth surface and make sure no components are missing before assembling.
If parts are missing, return the complete product to the place of purchase for inspection or replacement.
•Check whether the luminaire has been damaged during transport. Do not operate/install any product which appears
damaged in any way. Return the complete product to the place of purchase for inspection, repair or replacement.
•Do not plug into the mains power socket outlet before or during assembly. Only do so after the portable luminaire is
fully assembled and is ready to use for the first time.
Installation Directions
1. Remove all packaging material from the portable luminaire.
2. Select a suitable location for your portable lamp. See the requirements above.
3. Plug the LED driver connector (B) into the luminaire socket (C).
4. Plug the LED driver (A) into the mains socket outlet and ensure it is fully plugged in.
5. Turn on the mains power socket outlet.
6. Press the switch button (D) to turn the luminaire on and off. Press and hold the switch button (D) to adjust the brightness
level of the luminaire.
Operation of the USB charger (E):
You can charge your electronic device via the USB output (E) on the base of the luminaire.
The USB output (E) is rated DC 5V 2.1A.
(Refer to the instruction manual of your electronic device for the required charging current)
NOTE: If the charge current of your device is over the limit of the rated current, the charger will be self-protected.
In this case, your device will not charge unless you reconnect according to the rated output.

Installation Instructions
2 | P a g e v 1 . 1 ( 0 9 / 2 0 2 0 )
NOTE: If the charging current of your device is over the limit of the rated current, the charger will be self-
protected. In this case, your device will not charge unless you reconnect according to the rated output.
Safety Tips
•Always ensure the power is OFF and the portable luminaire has cooled down before performing any maintenance,
cleaning or making any adjustment to the portable luminaire.
•The external flexible cable or cord of this luminaire cannot be replaced; if the cable or cord is damaged, the luminaire
shall be destroyed.
•To avoid injury or damage to the luminaire, ensure that power leads and screws are secure before connecting the
power.
•Young children should be supervised to ensure that they do not play with the portable luminaire.
•Handle the luminaire and shade with care to avoid any damage or breakage.
•Select a suitable location away from liquids and hazards.
•To clean, wipe with a soft damp cloth. Do NOT soak or immerse the product in water or other liquids.
•Ensure that the luminaire does not come in contact with corrosive chemicals/solvents or abrasive cleaners etc..
•The light source of this luminaire is not replaceable; when the light source reaches its end of life, the whole luminaire
shall be replaced. There are no serviceable parts, do not attempt to dismantle or open the luminaire.
Specifications
SKU #
269391
269392
269393
Colour
Black
Aged Bronze
White
Rated Voltage
12V 2A
Rated Wattage
24W (13.5W LED light + 10.5W USB charger)
USB Charger
5V 2.1A
LED Specs
600 lumens, Warm White 3000K, CRI>80, Dimmable
Weight
2.5kg
Dimensions
H:395mm Dia:280mm
USB Charger
5V 2.1A