Lucent Technologies 4ESS User manual

TOP Comments Hot Line:
TM
Task Oriented Practice (TOP)
Do you
understand
how to use TOP
Go to 001
Go to 893
START
YesNo
4ESS
Monday through Friday
8:00 a.m. - 4:00 p.m. (Eastern)
Call: 1-888-LTINFO6
Or FAX to: 1-910-727-3043
Switch
Attached Processor
TPG
000
Issue 2 JAN 1998
TITLE PAGE
234-351-016
With 1B Processor
Interface Frame

Issue 2 LPG
000PAGE 1 of 1
JAN 1998
Trademarks
Ordering Information
Center, by using the following address or fax number.
Note:
Attention: Order Entry Department
2855 North Franklin Road
Indianapolis, Indiana 46219-1999
or
Process orders through your Technical Information Resourcec. Local Exchange Carriers (LEC):
d. Federal Government:
Fax: [phone]
e. All Others:
Developed by:
For permission to reproduce or distribute, please contact:
Notice
TM
Every effort is made to ensure that the document information is complete and accurate at the time of printing. However, information is subject to change.
not
Call: 1-888-LUCENT-8 Fax: [phone]
This material is protected by the copyright laws of the United States and other countries. It may be reproduced, distributed, or altered in any fashion by any entity
including other Lucent Technologies Business Units or Divisions without the expressed written consent of the Customer Training and Information Products Organization.
a. Lucent Technologies Employees:
Lucent Technologies Business Unit/Division and all required billing information must be provided.
Lucent Technologies Customer Information Center
b. AT&T:
Management (TIRM) coordinator. If you are unsure who your TIRM coordinator is, call 1-888-LUCENT-8
Lucent Technologies is the successor to the business and assets of AT&T
Network Systems business unit.
Submit orders by calling 1-800-432-6600 or fax to 1-800-566-9568
Orders must be faxed to the Lucent Technologies Customer Information Center using the following number:
Mail or fax Form IND 1-80.80, available from the Lucent Technologies Customer Information
To order this document and all associated documentation, use URL: "http://www.cic.lucent.com" or one of the following methods:
Copyright 1997 Lucent Technologies. All Rights Reserved.
C
Switch Documentation Customer Information Development Manager (1-888-LTINF06)
Call: 1-888-LUCENT-8 or fax to 1-800-566-9568
is a trademark of Lucent Technologies
Lucent Technologies Systems for Network Operators Switching and Access Information Development
4ESS
4ESS
TEKTRONIX
is a trademark of TEKTRONIX, Inc.
234-351-016

THEN GO TO. . . . . . . . . . . . . . . . .FIND YOUR JOB IN THE LIST BELOW
TASK INDEX LIST
Acceptance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NTP-002
Automatic Power Monitor Test Failure — Clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TAP-112
Converter; Power — Replace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NTP-004
Diagnostic Failure — TLP Abort — Clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TAP-108
Diagnostic Failure — TLP Inhibit — Clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TAP-107
Diagnostic Failure — TLP Tape Acquisition Error — Clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . TAP-110
Diagnostic Failure — TLP Queue Blockage — Clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TAP-106
Alarm Circuits; Power — Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DLP-502
133J Power Unit — Replace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NTP-004
Diagnostic Failure — TLP Disk Queue Full — Clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TAP-105
Diagnostic Failure — TLP Tape Not Mounted — Clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TAP-111
Blown —48V Fuse — Clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TAP-114
Diagnostic Failure — Clear By Replacing Packs on TLP Suspected Faulty Equipment List . . . . . . . . . . . . . . TAP-102
Diagnostic Failure — Clear By Analyzing Raw Data And Replacing Suspect Packs . . . . . . . . . . . . . . . . . . TAP-103
Blown +5V Fuse — Clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TAP-117
Diagnostic Failure — TLP Tape Version x Does Not Match Expected Version y — Clear . . . . . . . . . . . . . . . . TAP-109
Circuit Pack, API Unit — Replace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NTP-003
Clear Battery Distribution Fuse Board (BDFB) Frame Blown 45 Amp Fuse Associated With 1B Processor Cabinet . . . . TAP-122
Diagnostic Failure — Clear Auxiliary Unit Bus (AUB) Diagnostic Failure By Analyzing Raw Data . . . . . . . . . . TAP-120
Diagnostic Failure — Clear Auxiliary Unit Bus (AUB) Diagnostic Failure By Scoping AUB Using
Phase 99 Diagnostic Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TAP-121
IXL
PAGE 1 of 4 001
Issue 2 JAN 1998
234-351-016

THEN GO TO. . . . . . . . . . . . . . . . .FIND YOUR JOB IN THE LIST BELOW
TASK INDEX LIST
TTY Printout — DGN:API aPH bSTF
ANALY:TLPFILE API a
TTY Printout — DGN:API aPH bSTF
Power Monitor Test Failure; Automatic — Clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TAP-112
TLP Abort — Diagnostic Failure — Clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TAP-108
TLP Disk Queue Full — Diagnostic Failure — Clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TAP-105
TLP Inhibit — Diagnostic Failure — Clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TAP-107
TLP Tape Acquisition Error — Diagnostic Failure — Clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . TAP-110
TLP Tape Not Mounted — Diagnostic Failure — Clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TAP-111
TLP Tape Version x Does Not Match Expected Version y — Diagnostic Failure — Clear . . . . . . . . . . . . . . . TAP-109
TLP Queue Blockage — Diagnostic Failure — Clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TAP-106
Power Alarm Circuits — Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DLP-502
Power Unit; 133J — Replace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NTP-004
Power Switch — Replace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NTP-005
Power Alarm — Clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TAP-118
Power Switch Lamps — Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DLP-505
Switch; Power — Replace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NTP-005
Power Switch (KS-20738) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TAD-101
Maintenance Philosophy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TAD-100
Lamps; Power Switch — Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DLP-505
TLP PROGRAM ABORTED
ANALY:TLPFILE API ABORTED
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TAP-108
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TAP-108
TTY Printout — DGN:AUB PH STF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TAP-119ab
a
IXL
PAGE 2 of 4 001
Issue 2 JAN 1998
234-351-016

THEN GO TO. . . . . . . . . . . . . . . . .FIND YOUR JOB IN THE LIST BELOW
TASK INDEX LIST
TTY Printout — DGN:API aPH bSTF
ANALY:TLPFILE API aTLP
TLP TAPE ACQUISITION ERROR
TTY Printout — DGN:API aPH bSTF
ANALY:TLPFILE API aTLP
TTY Printout — DGN:API aPH bSTF
TTY Printout — DGN:API aPH bSTF
ANALY:TLPFILE API aSUSPECTED FAULTY EQUIPMENT
TTY Printout — DGN:API aPH bSTF
ANALY:TLPFILE API aSUSPECTED FAULTY EQUIPMENT
Note Column Contains NOTE 2
TTY Printout — DGN:API aPH bSTF
ANALY:TLPFILE API aSUSPECTED FAULTY EQUIPMENT
Note Column Contains NOTE 2
TTY Printout — DGN:API aPH bSTF
ANALY:TLPFILE API aSUMMARY DATA
TTY Printout — DGN:API aPH bSTF
ANALY:TLPFILE API aSUSPECTED FAULTY EQUIPMENT
Note Column Contains NOTE 2
No NOTE 2 in NOTE Column . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TAP-102
TTY Printout — DGN:API aPH bSTF
ANALY:TLPFILE API aTLP
CURRENT TLP SEARCH ABORTED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TAP-108
MOUNT TLP TAPE WITH FILE ID = F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TAP-110
WARNING:VERSION x DOES NOT MATCH EXPECTED VERSION y . . . . . . . . . . . . . . . . . . . . . . TAP-109
ANALY:TLPFILE API a NULL PACK TEST GENERATED . . . . . . . . . . . . . . . . . . . . . . . . . . TAP-103
5V Fuse Blown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TAP-117
No Fuses Blown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TAP-112
QUEUE ACCESS DENIED:DATA NOT RETAINED:CODE 001 . . . . . . . . . . . . . . . . . . . . . . . . . TAP-105
—48V Fuse Blown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TAP-114
IXL
PAGE 3 of 4 001
Issue 2 JAN 1998
234-351-016

THEN GO TO. . . . . . . . . . . . . . . . .FIND YOUR JOB IN THE LIST BELOW
TASK INDEX LIST
TTY Printout — DGN:API aPH bSTF
ANALY:TLPFILE API aSUMMARY DATA
TTY Printout — DGN:API aPH bSTF
TTY Printout — DGN:API aPH bSTF
ANALY:TLPFILE API aSUMMARY DATA
QUEUE ACCESS DENIED:DATA NOT RETAINED:CODE 002 . . . . . . . . . . . . . . . . . . . . . . . . . TAP-106
QUEUE ACCESS DENIED:DATA NOT RETAINED:CODE 004 . . . . . . . . . . . . . . . . . . . . . . . . . TAP-107
REPT:TAPE MUST BE MOUNTED FOR FUNCTION TLP . . . . . . . . . . . . . . . . . . . . . . . . . . . TAP-111
IXL
PAGE 4 of 4 001
Issue 2 JAN 1998
234-351-016

ACCEPTANCE
No acceptance test procedures are required for this frame.
Readiness of frame to become part of working system was
established by successful completion of Installation
Handbook test procedures
NTP
PAGE 1 of 1 002
Issue 2 JAN 1998
234-351-016

FOR DETAILS, GO TODO THE ITEMS BELOW IN THE ORDER LISTED . . . . . . . . . .
At Power Switch, Rotate ROS/OFF Switch Counterclockwise to Normal Position
2
3
4
—
—
At API Unit Power Switch, Rotate ROS/OFF Switch Clockwise to ROS
Replace Circuit Pack
Response: OFF NORM
Response: OFF NORM Lamp Lights
WARNING: Due to Static Charges, Precautions Must be Taken When Handling Circuit Packs —
DLP-500
RMV !
a bAt 1B Processor MTC Terminal, Remove Unit From Service ( )
1
RST !
a b
5
DLP-526
DLP-525
At 1B Processor MTC Terminal, Restore Unit To Service ( )
Lamp Goes Off
REPLACE CIRCUIT PACK — API UNIT NTP
PAGE 1 of 1 003
Issue 2 JAN 1998
234-351-016

FOR DETAILS, GO TODO THE ITEMS BELOW IN THE ORDER LISTED . . . . . . . . . .
At Power Switch, Rotate ROS/OFF Switch Counterclockwise to Normal Position
2
3
4
REPLACE 133J POWER UNIT
Replace Power Unit
—
—
At API Unit Power Switch, Rotate ROS/OFF Switch Clockwise to ROS
Response: OFF NORM Lamps Light
Response: OFF NORM Lamps Go Off
DLP-508
RMV !
a bAt 1B Processor MTC Terminal, Remove Unit From Service ( )
1 DLP-526
RST !
a b
5 DLP-525
At 1B Processor MTC Terminal, Restore Unit To Service ( )
NTP
PAGE 1 of 1 004
Issue 2 JAN 1998
234-351-016

Replace Power Switch
—
—
—
—
FOR DETAILS, GO TODO THE ITEMS BELOW IN THE ORDER LISTED . . . . . . . . . .
1
REPLACE POWER SWITCH
2
3
4
5
Response: OFF NORM Lamp Goes Off
At Power Switch, Rotate ROS/OFF Switch Clockwise to ROS
Response: RST:API COMPLETED; OS Lamp Goes Off
Response: RMV:API COMPLETED; OS Lamp Lights
Response: OFF NORM Lamp Lights
At TTY, Type:
RMV:API ! a = API Unit Member Number (0-1)
At TTY, Type: RST:API ! a = API Unit Member Number (0-1)
Rotate ROS/OFF Switch Counterclockwise to Normal Position
DLP-503
a
a
a
a
NTP
PAGE 1 of 1 005
Issue 2 JAN 1998
234-351-016

MAINTENANCE PHILOSOPHY
recovery program to request a diagnostic program. This
The IXL is structured to provide fast access to those
In general, logic circuit failures cause the fault
method of requesting the diagnostic program includes
the TLP option. The IXL reflects this in the TTY
supplementary messages pertain to problems in generating
a SUSPECTED FAULTY EQUIPMENT list and reference to
procedures (TAPs) which attempt to correct the problem.
If successful in generating a SUSPECTED FAULTY
that are designed to clear equipment problems. All other
problems are sensed by scan points which generate an
PWR OFF lamp lighted
and OFF NORM lamp off) or by reading the REPT:PA printout
which would identify the frame with the power fault. The
The Data Unit Selector (DUS) is not covered in this
frame. The DUS is electrically and functionally a
covered in TOP 234-351-010.
based upon design of equipment (hardware), diagnostic
software and test equipment employed. Procedures are
procedures pertinent to symptoms identified. Power
messages listed. Two supplementary messages,
which is an alternative to the first and most common
trouble-clearing approach.
LEDs on converters and power function circuit packs.
GENERAL
engineering, and software documentation such as I/O
Manuals, SDs, PKs, PRs, etc, which are available to
information in the TOP. Some portions of those
documents may be utilized in procedures but only as
examples for purposes of explanation. Test equipment
(oscilloscopes, voltmeters, etc) and parameters
involved in circuits being tested, adjusted, or
checked are usually prescribed. However, setup and
method operation is not described unless it is unusual
or unique.
IXL PHILOSOPHY
operating telephone company offices, are referenced
where applicable rather than duplicating that
the Input/Output (I/O) message manuals. Symptoms described
precise structure of the power alarm message is given in
other conditions that are observable at the frame that
would enable the user to access the proper trouble-clearing
ANALY:TLPFILE:SUSPECTED FAULTY EQUIPMENT and ANALY:
TLPFILE:NULL PACK TEST GENERATED, reference to procedures
EQUIPMENT list, those procedures reference the
appropriate procedure which identifies what to do with
TAP PHILOSOPHY
When documenting a procedural approach to trouble clearing,
replacements, the replacement part is always assumed to
be good. Equipment used for testing, both built-in
(hardware and software) and commercial, is assumed to
be good.
certain assumptions are made. It is assumed that only one
fault is being cleared at a time. When directing the user
performed correctly. Similarly, when directed to make
improvements to the data are encouraged. Manufacturer,
the user. Submittal of additions, corrections, and
procedure. These conditions are blown fuses and lighted
part of the Auxiliary Data System and is therefore
The maintenance philosophy contained in this pratice is
intended to aid personnel in performing trouble-clearing
the intended depends upon input and feedback from
alarm. The user should be able to follow aisle pilot
lights thereby locating the frame with the power fault
that is automatically powered down (
in the IXL reflect the preceding assumptions, and indicate
the next level of trouble clearing, raw data analysis,
this list. If not successful, these procedures reference
to perform an action, the action is assumed to have
tasks. The degree to which these procedures accomplish
practice although it is physically located in the API
100
Issue 2 JAN 1998
TAD
PAGE 1 of 3
234-351-016

MAINTENANCE PHILOSOPHY
and analyzing the results. This level is straightforward
and requires some familiarity with the equipment
where analyzation is completed (the faulty component
The more knowledgeable and experienced personnel may
In many instances, access to these procedures may be
procedures are designed for faults with consistent fault
signatures provide procedures with a clean straightline
approach to trouble clearing. A possibility exists that
Trouble-clearing TAPs provided for diagnostic failures
These assumptions and the fact that trouble-clearing
are provided on three levels. The level addresses
what to do with a software-generated (TLP) SUSPECTED
FAULTY EQUIPMENT list and provides a step-by-step
procedure for replacing circuit packs one at a time,
The level of trouble clearing is signal tracing
using interactive diagnostics. This procedure is
accessible only from the previous level and uses
information derived in the performance of that
procedure. This level of trouble clearing requires
an increase in the capabilities cited in the first
two levels with additional knowledge and skill in the
setup and use of test equipment (oscilloscopes,
voltmeters, etc).
access TOP documents at a point in trouble clearing
packs not previously identified. This level of trouble
determined) and only repair or replacement is required.
obtained by locating procedural data (DLPs) using a
TAPs and NTPs with preconditioning and system
restoration steps covered in those level procedures
(TAPs, NTPs). Therefore, access to data (DLPs) on a
hunt-and-find basis is a threat to equipment operation
and may compound trouble-clearing problems.
clearing is more complex and requires knowledge of the
equipment, TTY techniques and printouts, and SDs, PKs,
hunt-and-find method. Most DLPs are designed to support
general approach provided in the procedures. This
(descriptive and theory AT&T Practices), TTY techniques,
and diagnostic printouts.
The level of trouble clearing is accessed from
GENERATED
of the SUSPECTED FAULTY EQUIPMENT
ALTERNATE METHODS
TAP PHILOSOPHY (Contd)
the first level of trouble clearing; directly from
NULL PACK TEST
PRs, etc.
repeated a number of times, and the most consistent
signature and list are used following the same
repetitive diagnostic method is used each time to
action results in clearing the problem.
first
second
response. This level is known as raw data
the IXL or any TAP which produces a
analysis and describes what to do with the summary
and supplemental data printed either with or instead
list. This is
expected to lead to an identification of faulty
circuits and possibly additional suspect circuit
third
some faults do not present a consistent fault signature
or TLP pack list. If this occurs, the diagnostic is
detect any change in the fault signature when
any corrective action is taken unless that
100
Issue 2 JAN 1998
TAD
PAGE 2 of 3
234-351-016

MAINTENANCE PHILOSOPHY
6M Test Power Alarm Circuits
6M Test Power Lamps on Power Switch
Frequency, title, and procedure number
This is a list of tasks recommended for routine
preventive maintenance. Information on this list is
arranged in the following order from left to right:
EQUIPMENT TEST LIST
DLP-505
DLP-502
100
Issue 2 JAN 1998
TAD
PAGE 3 of 3
234-351-016

18
17
OFF & ON
SW
B
A
4
3
2
1
15
16
14
G
13
F
OFF & ON
SW
11
12
10
9 W
OFF & ON
SW
27
28
+
-
L1
21
22
8
7
31
30
29
26
23
24
25
32
D
OFF &
ON SW
J
B2 D2
B3 D3
TEST SW
PWR OFF
OFF NORM
ACK
B4 D4
B1 D1
K
C
6
5
OFF &
ON SW
19
20 H
ON SW
33
ROS
R SO
OS
B5 D5
Y
E
POWER SWITCH (KS-20738) TAD
PAGE 1 of 1 101
Issue 2 JAN 1998
234-351-016

diagnostic
result
ATP/CATP
STF
[5] Is
switch, rotate
counterclockwise
to normal position
ROS/OFF switch
DGN:API a!
CLEAR DIAGNOSTIC FAILURE BY REPLACING PACKS ON TLP SUSPECTED
FAULTY EQUIPMENT LIST
Replace each circuit pack on TLP suspected faulty equipment
list beginning with first pack. After each replacement,
check diagnostic results to determine if trouble is cleared.
If failure recurs, reinsert original pack. Repeat procedure
for each succeeding pack on list until trouble is cleared.
If trouble is not cleared, clear diagnostic failure by
a = API unit member
number (0-1)
[6] At API unit power
WARNING 1
Due to static
precautions must
be taken when
handling circuit
packs
lamp goes off)
[2] At API unit power
switch, rotate
ROS/OFF switch
OFF NORM
[3] See WARNING 1. Replace
clockwise to ROS
charges,
SUMMARY
AND
analyzing raw data and replacing suspect packs [TAP-103]
circuit pack [DLP-500]
[7] At 1B processor
MTC terminal, restore
Page 2,
Step 8
(Response: OFF NORM
lamp
lights
[1] At 1B processor
MTC terminal, remove
unit from service lamp
lights
OS
[4] At 1B processor MTC
(RMV:a b! [DLP-526]
terminal, type:
(RST:a b! [DLP-525]
unit to service
102
Issue 2 JAN 1998
TAP
PAGE 1 of 2
234-351-016

CLEAR DIAGNOSTIC FAILURE BY REPLACING PACKS ON TLP SUSPECTED
FAULTY EQUIPMENT LIST
packs on suspected
faulty equipment
list been replaced
[11] Clear
diagnostic failure
by analyzing raw
data and replacing
suspect packs
Step 3 for next
pack on suspected
faulty equipment
list
No
Yes
[9] Have all [10] Repeat from
[8] See WARNING 1.
Install original
circuit pack just
replaced
[TAP-103]
[DLP-500]
WARNING 1
Due to static
precautions must
be taken when
handling circuit
packs
charges,
102
Issue 2 JAN 1998
TAP
PAGE 2 of 2
234-351-016

Yes
No
suspect hardware
on list been
a = API unit member number
DGN:API a!
(0-1)
TABLE A
Circuit pack
Power switch
Power unit
CLEAR DIAGNOSTIC FAILURE BY ANALYZING RAW DATA
AND REPLACING SUSPECT PACKS
Identify suspect hardware by analyzing raw data printout.
Replace each suspect circuit pack or unit identified
diagnostic results to determine if trouble is cleared. If
failure recurs, reinsert original pack or unit. Repeat
procedure for each succeeding circuit pack or unit on list
diagnostic failure by looping over first failing test and
[3] Identify list of suspect
hardware using diagnostic
[4] Has all
replaced
previously
[5] Clear diagnostic
failure by looping
over first failing
test and signal
until trouble is cleared. If trouble is not cleared, clear
[2] At API unit power switch,
ensure ROS/OFF switch is
rotated clockwise to ROS
[6] See WARNING 1. Replace
WARNING 1
Due to static
precautions must
be taken when
handling circuit
packs
suspect hardware [TABLE A]
charges,
SUMMARY
AND
AND
DLP-500
DLP-508
DLP-503
information [DLP-501]
tracing [TAP-104]
signal tracing [TAP-104]
beginning with the first. After each replacement, check
Page 2,
[1] At 1B processor
MTC terminal, remove
unit from service lamp
lights
OS
OFF NORM
lamp lights
Step 8
(RMV:a b! [DLP-526]
[7] At TTY, type:
103
Issue 2 JAN 1998
TAP
PAGE 1 of 2
234-351-016

diagnostic
result
STF
[8] Is
CLEAR DIAGNOSTIC FAILURE BY ANALYZING RAW DATA
AND REPLACING SUSPECT PACKS
[10] At API unit power
switch counterclockwise
to normal position
switch, rotate ROS/OFF
[9] See WARNING 1.
Install original
hardware just
replaced and
repeat from Step 4
ATP/CATP
(Response:
lamps go off)
[11] At 1B processor
MTC terminal, restore
unit from service
OFF NORM
WARNING 1
Due to static
precautions must
be taken when
handling circuit
packs
charges,
(RST:a b! [DLP-525]
103
Issue 2 JAN 1998
TAP
PAGE 2 of 2
234-351-016

to frame under test
MACLI MTCE
SUBCLASS assigned
[1] Obtain and power up oscilloscope allowing
[2] Determine failing phase and looping
NOTE 1
OP:MACLI,CLASS MTCE !
MTCE,SUBCLASS a!
assigned to
period for stabilization
CLEAR DIAGNOSTIC FAILURE BY LOOPING OVER FIRST FAILING TEST
AND SIGNAL TRACING
a = API unit member number (0-1)
a = API unit member number (0-1)
b = Identified looping parameters
c = Failing test number
a = API unit member number (0-1)
b = Failing phase number
c = Identified looping parameters
failing test
raw data
printed twice
OP:MACLI,CLASS MTCE!
(System responds with
OP:MACLI message
indicating subclass
assigned to unit
[8] Is MTCE
subclass
available
[10] Repeat
from
Step 3
[9] After
short period,
repeat
from Step 2
Yes
No
Yes
No
[5] Type: EX:API a;RPT 2:PH b,ADR c!
[6] Is first
[4] Type: EX:API a:SYNC b,ENABLE c!
M13 OP:MACLI
CLASS MTCE SUBCLASS 0 4 69 0 142612...
CLASS MTCE SUBCLASS 1 NONE
CLASS MTCE SUBCLASS 2 NONE
AVAILABLE
OCCUPIED
EX:API a;START!
Then type:
AND Page 2
parameters [DLP-504]
[3] See NOTE 1. At TTY, type:
[7] Type:
[Figure 1])
Figure 1 — Example of MACLI Output Message
To discontinue
looping condition,
the
Type:
STOP:MACLI,CLASS
a = Subclass
frame under test
should be identified.
104
Issue 2 JAN 1998
TAP
PAGE 1 of 2
234-351-016

CD, PK, circuit pack
analysis to trace
signal path of failing
data, and raw data
CLEAR DIAGNOSTIC FAILURE BY LOOPING OVER FIRST FAILING TEST
AND SIGNAL TRACING
[11] Set up oscilloscope for signal tracing
a = API unit member number (0-1)
a = API unit member number (0-1)
b = Identified looping parameters
c = Failing test number
a = API unit member number (0-1)
b = Failing phase number
c = Identified looping parameters
[15] Use frame SD,
bits to isolate and
clear fault
[12] At TTY, type: EX:API a;START!
[14] Type: EX:API a:PH b,ADR c!
[13] Type: EX:API a:SYNC b,ENABLE c! AND
Figure 2 — SYNC Terminal Location
using external sweep trigger [Figure 2]
MCC [ ]
MCC [ ]
UTIL AWL
UTIL AWL
UXT041
GCP161
UXCCM01
UXCCM11
UYCM11
UYCM01
UYM01
UYM11
T
E
L
[ ]
T
T
Y
SYNC USING
ACTIVE CC
104
Issue 2 JAN 1998
TAP
PAGE 2 of 2
234-351-016