LumaPro 39UU86 User manual

Please read and save these instructions. Read through this owner’s manual carefully before
using product. Protect yourself and others by observing all safety information, warnings, and
cautions. Failure to comply with instructions could result in personal injury and/or damage to
product or property. Please retain instructions for future reference.
Operating Instructions 39UU86, 39UU89, 39UU96, 39UU97
LED Bullet
Floods
Description
LED Bullet Flood Lights provide energy-efficient, directional lighting for landscape, facade
and outdoor signage. Sealed to keep out dirt, bugs and moisture, the Bullet is constructed
with a precision die-cast aluminum housing and tempered, shatter-resistant glass for
durability.
Picture is for illustration purposes only. Your model may vary.
CONSTRUCTION
• Die cast aluminum body
• Bronze polyester powder coat finish
• Sealed to keep out dirt and bugs
• Tempered shatter resistant glass lens
• Weep hole located on lower lip of fixture to prevent buildup
• ½” NPT threaded arm with locking swivel
Specifications and Dimensions
39UU86 120-277V 30W 5000K 2,500 75 6.9” x 8.3” x 6.2”
39UU89 120-277V 30W 3000K 2,115 75 6.9” x 8.3” x 6.2”
39UU96 120-277V 12W 3000K 790 75 7.8” x 10” x 8.1”
39UU97 120-277V 12W 5000K 810 75 7.8” x 10” x 8.1”
Dimensions (in)
Model Volts Watts CCT Lumens CRI H” x L” x D”

2
LumaPro Operating Instructions
39UU86, 39UU89, 39UU96, 39UU97
LED Bullet
Floods
General Safety Information
• To reduce the risk of death, personal injury or property damage from fire, electric shock,
falling parts, cuts/abrasions, and other hazards read all warnings and instructions
included with and on the fixture box and all fixture labels.
• Before installing, servicing, or performing routine maintenance upon this equipment, follow
these general precautions.
• Commercial installation, service and maintenance of luminaires should be performed by a
qualified licensed electrician.
• For Residential installation: If you are unsure about the installation or maintenance of the
luminaires, consult a qualified licensed electrician and check your local electrical code.
• DO NOT INSTALL DAMAGED PRODUCT!
• This fixture is intended to be connected to a properly installed and grounded UL
listed junction box.
WARNING:
RISK OF ELECTRICALSHOCK
• Turn off electrical power at fuse or circuit breaker box before wiring fixture to the power
supply.
• Turn off the power when you perform any maintenance.
• Verify that supply voltage is correct by comparing it with the luminaire label information.
• Make all electrical and grounded connections in accordance with the National Electrical
Code and any applicable local code requirements.
• All wiring connections should be capped with UL approved wire connectors.
CAUTION:
RISK OF INJURY
• Wear gloves and safety glasses at all times when removing luminaire from carton,
installing, servicing or performing maintenance.
• Avoid direct eye exposure to the light source while it is on.
• Account for small parts and destroy packing material, as these may be hazardous to
children.
CAUTION:
RISK OF FIRE
• Keep combustible and other materials that can burn away from luminaire and lamp/lens.
• MIN 90°C SUPPLY CONDUCTORS.
Operating Temperature: -22°F to 104°F

3
LumaPro Operating Instructions
39UU86, 39UU89, 39UU96, 39UU97
LED Bullet
Floods
Wiring Diagram
Installation Instructions
1.) Inspect components to ensure that male and
female port threads and sealing surfaces are free
of burs, nicks and scratches or any foreign
material.
2.) Thread fixture into cover plate (not included)
or ground stake (not included) as shown.
3.) Using two wrenches, hold fitting at desired aiming
angle and tighten locknut without exceeding the
rated torque value of 350 in. lbs.
4.) Inspect to ensure that the washer is seated flat
on the mounting surface.
5.) Connect power to fixture, referencing wiring
diagram. Make sure the power supply is
disconnected before installing.
6.) Supply power to the fixture and enjoy your new LED Bullet Flood.
Warranty
LIMITED FIVE-YEAR WARRANTY
Should this product fail to perform satisfactorily due to a defect or poor workmanship within
FIVE YEAR from the date of purchase, return it to the place of purchase and it will be
replaced, and free of charge. Incidental or consequential damages are excluded from this
warranty.
Manufactured for Grainger International, Inc.
100 Grainger Pkwy., Lake Forest IL 60045 U.S.A.