Lumascape PowerSync PS User manual

READ ALL SAFETY INSTRUCTIONS FIRST
›Follow all safety instructions carefully. Failure to do so will
void warranty.
›Ensure installation complies with local laws and any
applicable standards.
›Only use Lumascape power supply, control equipment and
leader cables.
›Ensure mains input power is surge protected.
›Never make connections whilst the power is connected.
›Do not make modifications or alter product.
›Keep luminaire clean and free of debris.
›Connectors are to be kept clean and dry at all times.
›Once installed, all connectors are to be mated and a
PowerSyncTM terminator is required on the last fitting of run.
LS6540
PowerSync™ PS Data Injector
Installation Instructions
ASIA PACIFIC 18 Brandl Street, Eight Mile Plains, QLD 4113, Australia P: [phone] | F: [phone] | E: [e-mail] | www.lumacape.com.au
NORTH AMERICA 1940 Diamond Street, San Marcos, CA 94070, USA P: [phone] | F: [phone] | E: [email protected] | www.lumacape.com
IN0172 N191118

ASIA PACIFIC 18 Brandl Street, Eight Mile Plains, QLD 4113, Australia P: [phone] | F: [phone] | E: [e-mail] | www.lumacape.com.au
NORTH AMERICA 1940 Diamond Street, San Marcos, CA 94070, USA P: [phone] | F: [phone] | E: [email protected] | www.lumacape.com
1 / 17IN0172 N191118
Products and specifications are subject to change without notice.
Table of Contents
LS6540
Product Overview ................................................................. 2
Mode Switch and Indicator Light Descriptions ........... 3
Wiring for DMX Controllers
International .................................................................... 4
North America ................................................................ 5
Wiring for 0-10 V Sinking Dimmers
International .................................................................... 6
North America .................................................................7
Wiring for Sourcing Dimmers
International .................................................................... 8
North America ................................................................ 9
Phase Dimming Calibration..............................................10
Wiring for Trailing Edge Phase Dimmers
International ....................................................................11
North America ...............................................................12
Testing Functions.................................................................13
Network Installation............................................................14
System Limitations ..............................................................15
PowerSync™ PS Data Injector
Installation Instructions

ASIA PACIFIC 18 Brandl Street, Eight Mile Plains, QLD 4113, Australia P: [phone] | F: [phone] | E: [e-mail] | www.lumacape.com.au
NORTH AMERICA 1940 Diamond Street, San Marcos, CA 94070, USA P: [phone] | F: [phone] | E: [email protected] | www.lumacape.com
2 / 17 IN0172 N191118
Products and specifications are subject to change without notice.
PowerSync™ PS Data Injector
Installation Instructions
Product Overview
Lid Screws
Use Allen key to remove lid
screws and access the interior
of the PowerSyncTM enclosure.
Plug
Leave plug in place if not
required for cable entry.
Plug
Remove one plug for each required
cable entry and replace with suitable
cable gland or conduit adaptor.
Seal
If required, retain and use seal provided to
ensure a water tight seal between cable, gland
and encloure.
Electronic equipment inside. Failing to seal
enclosure properly will void warranty.
Mounting Holes
Use suitable screws (6mm or ¼") and flat washers to attach enclosure to
suitable mounting surface.
Observe orientation diagram in back of enclosure for correct orientation.
Enclosure should be mounted in a vertical orientation so that the cable
entries do not face upwards.
DANGER
ISOLATE DEVICE FROM POWER
Failure to isolate power
supply before installation or
maintenance may result in
fire, serious injury, electric
shock, death and may
damage the luminaire.
NO POWER
TOOLS
DO NOT USE SILICONE
ON OUTSIDE SURFACE
KEEP ELECTRONICS FREE
FROM DIRT AND MOISTURE
DO NOT HOSE OR
PRESSURE CLEAN
N653
LS6406
3 x PowerSync Terminator
LS6407
1 x DMX Terminator

ASIA PACIFIC 18 Brandl Street, Eight Mile Plains, QLD 4113, Australia P: [phone] | F: [phone] | E: [e-mail] | www.lumacape.com.au
NORTH AMERICA 1940 Diamond Street, San Marcos, CA 94070, USA P: [phone] | F: [phone] | E: [email protected] | www.lumacape.com
3 / 17IN0172 N191118
Products and specifications are subject to change without notice.
Mode Switch and Indicator Light Descriptions
PowerSync™ PS Data Injector
Installation Instructions
Ferrules must be used
with stranded wire
Scale 1: 1
STRANDED ONLY
1.5–6.0 mm
2
15mm
16–8A WG
0.6"
LUMASCAPE
www.lumascape.com
Phase
control
Power in
Data
Power
PowerSync
PowerSync out
PWM/ 0–10V
Mode USB
Cat 5 (and similar) cable
termination according to
T568A colour scheme
Scale 1: 1
STRANDED/SOLID
0.2–1.5 mm
2
10mm
24–16 AWG
0.4"
Status
Check
Use with Lumascape wireless DMX
DMX in DMX out
GND
GND
Com 10V out
Ch 1 in Ch 2 in
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
techsupport.lumascape.com
DMX Trac
L N L N
Mode Switch
Label Descriptions
0 DMX/RDM
1 DMX/RDM with Relay Control
2 TEST: All channels OFF
3 TEST: All channels ON
4 TEST: Cycle 4 Channels
5 0-10 V Dimming: Sourcing / PWM Dimming
6 0-10 V Dimming: Sinking / PWM Dimming: Inverted
7 Phase Dimming
8 USB
9 Reserved
10 DMX/RDM with SIP
11 Reserved
12 Reserved
13 Reserved
14 Erase Parameters
15 Reserved
Indicator Light
LED Indicator Event Appearance Note
Power Main Input Power Illuminates
PowerSync™ PowerSync™ output enabled Illuminates
Status
Start Up 3 flashes
Normal Operation 1 flash, every 5 seconds
Circuit Fault: Over Voltage 2 flashes, every 5 seconds
PowerSync™ Fault 4 flashes, every 5 seconds
Phase Dimming Calibration 3 flashes on calibration event See Phase Dimming
Erase Parameters 3 flashes on erase event See Phase Dimming
Check
Start Up On
Normal Operation O
Relay Open: Fault Detected On
Relay Open: Manual Override Flashing
USB USB Connected Illuminates / flashes with data
DMX Trac
DMX Trac Detected Flashing with DMX frames
Dimming Signal Detected 1-20 Hz flashing proportional to input level 0-10 V, PWM and Phase Dimming
Phase Dimming Locked Illuminates See Phase Dimming
QUESTIONS
Contact us at details below
LS6540

ASIA PACIFIC 18 Brandl Street, Eight Mile Plains, QLD 4113, Australia P: [phone] | F: [phone] | E: [e-mail] | www.lumacape.com.au
NORTH AMERICA 1940 Diamond Street, San Marcos, CA 94070, USA P: [phone] | F: [phone] | E: [email protected] | www.lumacape.com
4 / 17 IN0172 N191118
Products and specifications are subject to change without notice.
PowerSync™ PS Data Injector
Installation Instructions
Wiring for DMX Controllers (International)
Mode Switch Set to Mode 0
DMX In
Colour T-568A Colour T-568B Label Designation
White / Brown White / Brown GND Ground
Green Orange − Data −
White / Green White / Orange + Data +
DMX Out to next PowerSync™ Data Injector
(optional)
Colour T-568A Colour T-568B Label Designation
Green Orange − Data −
White / Green White / Orange + Data +
White / Brown White / Brown GND Ground
Connect to DMX in terminals of next PowerSyncTM Data Injector for DMX
loop-through functionality.
NOTE: If the output is not used, either LS6407 DMX Terminator (included
with PowerSyncTM Injector) or a 120 Ω, 0.125 W resistor must be inserted
between Data + and Data − of the DMX out terminals.
Refer to third
party installation
instructions for details
on dimmer installation.
Power In (International)
Colour Label Designation
Blue N Neutral
Green / Yellow Earth
Brown L Live (110-240 V)
PowerSync™ Out to Luminaires
Colour Label Designation
Blue N Neutral
Green / Yellow Earth
Brown L Live (110-240 V)
Black* Data PowerSync™ Data
* Connecting high voltage to data terminal will cause
permanent damage and void warranty.
LUMASCAPE
www.lumascape.com
Power
PowerSync
Mode USB
Status
Check
Use with Lumascape wireless DMX
DMX in DMX out
GND
GND
Com 10V out
Ch 1 in Ch 2 in
0
1
2
3
4
5
6
7
8
9
10
12
11
14
1
3
1
5
DMX Trac
techsupport.lumascape.com
At the end of the run, connect
the LS6407 DMX Terminator
between Data + and Data - of
the DMX out terminal in the
final PowerSyncTM Data Injector.
DMX Termination
PWM/ 0–10V
de USB
Cat 5 (and similar) cable
termination according to
T568A colour scheme
Use with Lumascape wireless DMX
DMX in DMX out
GND
GND
Com 10V out
Ch 1 in Ch 2 in
1
2
3
4
5
6
7
DMX Trac
techsupport.lumascape.com
Label Description
0 DMX/RDM
1 DMX/RDM with Relay Control / Energy Saving
2 TEST: All Channels OFF
3 TEST: All Channels ON
4 TEST: Cycle 4 Channels
8 USB
Mode Switch Key
When there is no DMX
or the DMX level is 0 on all
channels for 15 minutes the
PowerSync™ will de-energise
the outgoing circuit.
MODE 1: DMX / RDM with
Relay Control / Energy Saving

ASIA PACIFIC 18 Brandl Street, Eight Mile Plains, QLD 4113, Australia P: [phone] | F: [phone] | E: [e-mail] | www.lumacape.com.au
NORTH AMERICA 1940 Diamond Street, San Marcos, CA 94070, USA P: [phone] | F: [phone] | E: [email protected] | www.lumacape.com
5 / 17IN0172 N191118
Products and specifications are subject to change without notice.
Wiring for DMX Controllers (International)
LS6540
PowerSync™ PS Data Injector
Installation Instructions
Wiring for DMX Controllers (North America)
DMX Out to next PowerSync™ Data Injector
(optional)
Colour T-568A Colour T-568B Label Designation
Green Orange − Data −
White / Green White / Orange + Data +
White / Brown White / Brown GND Ground
Connect to DMX in terminals of next PowerSyncTM Data Injector for DMX
loop-through functionality.
NOTE: If the output is not used, either LS6407 DMX Terminator (included
with PowerSyncTM Injector) or a 120 Ω, 0.125 W resistor must be inserted
between Data + and Data − of the DMX out terminals.
DMX In
Colour T-568A Colour T-568B Label Designation
White / Brown White / Brown GND Ground
Green Orange − Data −
White / Green White / Orange + Data +
Refer to third
party installation
instructions for details
on dimmer installation.
At the end of the run, connect
the LS6407 DMX Terminator
between Data + and Data - of
the DMX out terminal in the
final PowerSyncTM Data Injector.
DMX Termination
PWM/ 0–10V
de USB
Cat 5 (and similar) cable
termination according to
T568A colour scheme
Use with Lumascape wireless DMX
DMX in DMX out
GND
GND
Com 10V out
Ch 1 in Ch 2 in
1
2
3
4
5
6
7
DMX Trac
techsupport.lumascape.com
Mode Switch Set to Mode 0
LUMASCAPE
www.lumascape.com
Power
PowerSync
Mode USB
Status
Check
Use with Lumascape wireless DMX
DMX in DMX out
GND
GND
Com 10V out
Ch 1 in Ch 2 in
0
1
2
3
4
5
6
7
8
9
10
12
11
14
1
3
1
5
DMX Trac
techsupport.lumascape.com
Power In
Colour Label Designation
White N Neutral
Green / Yellow Earth
Black L Live (120-277 V)
PowerSync™ Out to Luminaires
Colour Label Designation
White N Neutral
Green / Yellow Earth
Black L Live (120-277 V)
Grey* Data PowerSync™ Data
* Connecting high voltage to data terminal will cause
permanent damage and void warranty.
Label Description
0 DMX/RDM
1 DMX/RDM with Relay Control / Energy Saving
2 TEST: All Channels OFF
3 TEST: All Channels ON
4 TEST: Cycle 4 Channels
8 USB
Mode Switch Key
When there is no DMX
or the DMX level is 0 on all
channels for 15 minutes the
PowerSync™ will de-energise
the outgoing circuit.
MODE 1: DMX / RDM with
Relay Control / Energy Saving

ASIA PACIFIC 18 Brandl Street, Eight Mile Plains, QLD 4113, Australia P: [phone] | F: [phone] | E: [e-mail] | www.lumacape.com.au
NORTH AMERICA 1940 Diamond Street, San Marcos, CA 94070, USA P: [phone] | F: [phone] | E: [email protected] | www.lumacape.com
6 / 17 IN0172 N191118
Products and specifications are subject to change without notice.
LUMASCAPE
www.lumascape.com
Power
PowerSync
Mode USB
Status
Check
Use with Lumascape wireless DMX
DMX in DMX out
GND
GND
Com 10V out
Ch 1 in Ch 2 in
0
1
2
3
4
5
6
7
8
9
10
12
11
14
1
3
1
5
DMX Trac
techsupport.lumascape.com
Wiring for 0-10 V Sinking Dimmers (International)
Refer to third party installation
instructions for details on
dimmer installation.
Mode Switch Set to Mode 6.
DMX Out to next PowerSync™ Data Injector
(optional)
Colour T-568A Colour T-568B Label Designation
Green Orange − Data −
White / Green White / Orange + Data +
White / Brown White / Brown GND Ground
Connect to DMX in terminals of next PowerSyncTM Data Injector
for DMX loop-through functionality.
Power In
Colour Label Designation
Blue N Neutral
Green / Yellow Earth
Brown L Live (110-240 V)
PowerSync™ Out to Luminaires
Colour Label Designation
Blue N Neutral
Green / Yellow Earth
Brown L Live (110-240 V)
Black* Data PowerSync™ Data
* Connecting high voltage to data terminal will cause
permanent damage and void warranty.
0-10 V In from sinking dimmer
Colour Label Designation
Grey Ch 2 In Channel 2 return (optional)
Grey Ch 1 In Channel 1 return
Purple 10 V Out 10 V source
Please Note:
Attached luminaires need to be configured as
single channel, DMX address (Channel 1 In Only)
or Tuneable White (Channel 1 In & Channel 2 In).
!
PowerSync™ PS Data Injector
Installation Instructions
Label Description
5 0-10 V Dimming: Sourcing / PWM Dimming
6 0-10 V Dimming: Sinking / PWM Dimming: Inverted
2 TEST: All Channels OFF
3 TEST: All Channels ON
4 TEST: Cycle 4 Channels
8 USB
Mode Switch Key
NOTE: 0-10 V level is digitized and
passed out as DMX.

ASIA PACIFIC 18 Brandl Street, Eight Mile Plains, QLD 4113, Australia P: [phone] | F: [phone] | E: [e-mail] | www.lumacape.com.au
NORTH AMERICA 1940 Diamond Street, San Marcos, CA 94070, USA P: [phone] | F: [phone] | E: [email protected] | www.lumacape.com
7 / 17IN0172 N191118
Products and specifications are subject to change without notice.
Label Description
5 0-10 V Dimming: Sourcing / PWM Dimming
6 0-10 V Dimming: Sinking / PWM Dimming: Inverted
2 TEST: All Channels OFF
3 TEST: All Channels ON
4 TEST: Cycle 4 Channels
8 USB
Mode Switch Key
LUMASCAPE
www.lumascape.com
Power
PowerSync
Mode USB
Status
Check
Use with Lumascape wireless DMX
DMX in DMX out
GND
GND
Com 10V out
Ch 1 in Ch 2 in
0
1
2
3
4
5
6
7
8
9
10
12
11
14
1
3
1
5
DMX Trac
techsupport.lumascape.com
Wiring for 0-10 V Sinking Dimmers (North America)
Mode Switch Set to Mode 6.
Power In
Colour Label Designation
White N Neutral
Green / Yellow Earth
Black L Live (120-277 V)
PowerSync™ Out to Luminaires
Colour Label Designation
White N Neutral
Green / Yellow Earth
Black L Live (120-277 V)
Grey* Data PowerSync™ Data
* Connecting high voltage to data terminal will cause
permanent damage and void warranty.
0-10 V In from sinking dimmer
Colour Label Designation
Grey Ch 2 In Channel 2 return (optional)
Grey Ch 1 In Channel 1 return
Purple 10 V Out 10 V source
Please Note:
Attached luminaires need to be configured as
single channel, DMX address (Channel 1 In Only)
or Tuneable White (Channel 1 In & Channel 2 In).
!
PowerSync™ PS Data Injector
Installation Instructions
DMX Out to next PowerSync™ Data Injector
(optional)
Colour T-568A Colour T-568B Label Designation
Green Orange − Data −
White / Green White / Orange + Data +
White / Brown White / Brown GND Ground
Connect to DMX in terminals of next PowerSyncTM Data Injector for DMX
loop-through functionality.
Refer to third party installation
instructions for details on
dimmer installation.
NOTE: 0-10 V level is digitized and
passed out as DMX.
LS6540

ASIA PACIFIC 18 Brandl Street, Eight Mile Plains, QLD 4113, Australia P: [phone] | F: [phone] | E: [e-mail] | www.lumacape.com.au
NORTH AMERICA 1940 Diamond Street, San Marcos, CA 94070, USA P: [phone] | F: [phone] | E: [email protected] | www.lumacape.com
8 / 17 IN0172 N191118
Products and specifications are subject to change without notice.
LUMASCAPE
www.lumascape.com
Power
PowerSync
Mode USB
Status
Check
Use with Lumascape wireless DMX
DMX in DMX out
GND
GND
Com 10V out
Ch 1 in Ch 2 in
0
1
2
3
4
5
6
7
8
9
10
12
11
14
1
3
1
5
DMX Trac
techsupport.lumascape.com
Wiring for 0-10 V Sourcing Dimmers (International)
Mode Switch Set to Mode 5.
Power In
Colour Label Designation
Blue N Neutral
Green / Yellow Earth
Brown L Live (110-240 V)
PowerSync™ Out to Luminaires
Colour Label Designation
Blue N Neutral
Green / Yellow Earth
Brown L Live (110-240 V)
Black* Data PowerSync™ Data
* Connecting high voltage to data terminal will cause
permanent damage and void warranty.
0-10 V In from sourcing dimmer
Label Designation
Com Common –
Ch 2 In Channel 2 + (optional)
Ch 1 In Channel 1 +
Please Note:
Attached luminaires need to be configured as
single channel, DMX address (Channel 1 In Only)
or Tuneable White (Channel 1 In & Channel 2 In).
!
PowerSync™ PS Data Injector
Installation Instructions
DMX Out to next PowerSync™ Data Injector
(optional)
Colour T-568A Colour T-568B Label Designation
Green Orange − Data −
White / Green White / Orange + Data +
White / Brown White / Brown GND Ground
Connect to DMX in terminals of next PowerSyncTM Data Injector
for DMX loop-through functionality.
Refer to third party installation
instructions for details on
dimmer installation.
Label Description
5 0-10 V Dimming: Sourcing / PWM Dimming
6 0-10 V Dimming: Sinking / PWM Dimming: Inverted
2 TEST: All Channels OFF
3 TEST: All Channels ON
4 TEST: Cycle 4 Channels
8 USB
Mode Switch Key
NOTE: 0-10 V level is digitized and
passed out as DMX.

ASIA PACIFIC 18 Brandl Street, Eight Mile Plains, QLD 4113, Australia P: [phone] | F: [phone] | E: [e-mail] | www.lumacape.com.au
NORTH AMERICA 1940 Diamond Street, San Marcos, CA 94070, USA P: [phone] | F: [phone] | E: [email protected] | www.lumacape.com
9 / 17IN0172 N191118
Products and specifications are subject to change without notice.
PowerSync™ PS Data Injector
Installation Instructions
LUMASCAPE
www.lumascape.com
Power
PowerSync
Mode USB
Status
Check
Use with Lumascape wireless DMX
DMX in DMX out
GND
GND
Com 10V out
Ch 1 in Ch 2 in
0
1
2
3
4
5
6
7
8
9
10
12
11
14
1
3
1
5
DMX Trac
techsupport.lumascape.com
Wiring for 0-10 V Sourcing Dimmers (North America)
Mode Switch Set to Mode 5.
Power In
Colour Label Designation
White N Neutral
Green / Yellow Earth
Black L Live (120-277 V)
PowerSync™ Out to Luminaires
Colour Label Designation
White N Neutral
Green / Yellow Earth
Black L Live (120-277 V)
Grey* Data PowerSync™ Data
* Connecting high voltage to data terminal will cause
permanent damage and void warranty.
0-10 V In from sourcing dimmer
Label Designation
Com Common –
Ch 2 In Channel 2 + (optional)
Ch 1 In Channel 1 +
Please Note:
Attached luminaires need to be configured as
single channel, DMX address (Channel 1 In Only)
or Tuneable White (Channel 1 In & Channel 2 In).
!
DMX Out to next PowerSync™ Data Injector
(optional)
Colour T-568A Colour T-568B Label Designation
Green Orange − Data −
White / Green White / Orange + Data +
White / Brown White / Brown GND Ground
Connect to DMX in terminals of next PowerSyncTM Data Injector for DMX
loop-through functionality.
Refer to third party installation
instructions for details on
dimmer installation.
Label Description
5 0-10 V Dimming: Sourcing / PWM Dimming
6 0-10 V Dimming: Sinking / PWM Dimming: Inverted
2 TEST: All Channels OFF
3 TEST: All Channels ON
4 TEST: Cycle 4 Channels
8 USB
Mode Switch Key
NOTE: 0-10 V level is digitized and
passed out as DMX.
LS6540