Lumena Prosolar Hiway 15 PIR User manual

Full product range & more information: www.lumenalights.com
USER MANUAL
Hiway 15 PIR Motion Sensor Auto-adjust Solar Light
THANK YOU FOR YOUR PURCHASE
PLEASE READ THESE INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION / MAINTENANCE
WARNINGS
•If a fitting is found to be damaged, cease use immediately.
•The unit may get warm whilst on for a period of time.
•Always take care when installing your solar light, especially when mounting it in high places.
•Ensure the fitting is mounted out of range of head height to avoid injury.
•Fitting must be mounted to a solid surface.
•This Solar Light will not charge correctly if the panel is behind glass or artificial light is used.
•For replacement battery, contact the manufacturer.
CLEANING & MAINTENANCE:
Occasional cleaning and care are recommended for this product. Wipe with a soft, slightly damp cloth to remove any surface
dirt. To maintain efficiency, specifically clean the solar panel, LEDs and PIR on a regular basis. Also, keep the solar panel free of
debris and snow to prevent reduced battery life or malfunction. Do not use abrasive cleaners or a lot of water as this could
damage the fitting. Please refer to our website for more information on the best way to clean different materials.
RETURNS:
If purchased from a 3rd party, please contact your supplier. If purchased direct, contact us by phone or email:
Lumena Lights Ltd, Centre 33 Long March, Daventry, NN11 4NR Tel: [phone] Email: [e-mail]
Our full returns policy is available on our website.
Waste Electrical Products should not be disposed of with household waste. Please check with your local authority or contact us
for more information. Please recycle packaging whenever possible.
Producer Registration Number: WEE/KC3440XY
SPECIFICATIONS
Wattage: 15w
Lamp: In-built LED x 40 (SMD 2835)
Colour Temperature: 6000K (Daylight White) / 3000K (Warm White)
Lumen Output: 1600 lm
LED Life Expectancy: up to 35,000 hours
Max Illumination Time at Full Charge: up to 5 nights
Sensor: PIR (Motion Sensor) + Photocell (Dusk to Dawn)
PIR Distance: Up to 8m
PIR Sensor Delay Time: approx. 20 seconds
PIR Sensor Angle: 120 degrees
Battery Type: Lithium Ion 18650 7.4v 5400mAh (Replaceable) –Total Capacity 10800mAh
Battery Lifespan: up to 8 years
Battery Charge Time: 10 -12 hours
Solar Panel: 9.5Wp Polycrystalline Silicon –Lifespan up to 5 years
IP Rating: IP65
Materials: Aluminium, Polycarbonate, Tempered Glass
Weight: 1950g (approx.)
Mounting: Surface mount bracket & pole adaptor supplied
Install Height: 2-5m recommended
Functions: Auto Adjust –see modes / settings
✔✔✔
3 YEAR
GUARANTEE
see website for
more details
290mm
110mm
50mm
412mm
10mm
58mm
230mm
135 x 115mm

Full product range & more information: www.lumenalights.com
HIWAY 15 TECHNOLOGY:
The Hiway 5 is a highly efficient solar light with high capacity Lithium Ion batteries and a fast charging Polycrystalline solar panel.
This means that even on cloudy and rainy days, it will re-charge efficiently. The high battery capacity gives enough power for up
to 5 nights when there is little light during the day. The 1600 lumen light output is bright enough to illuminate driveways and
paths, making them safe to navigate at night.
INSTALLATION:
Designed to be mounted on a flat surface or right-angled post (40-50mm diameter) at a height of 2-5m. The higher the light is
mounted, the larger the illuminated area.
Location –It is important that the installation location is carefully considered, avoiding shady areas. The best position is south
facing, however the light can work facing in other directions, especially when in full sunshine. The PIR must face the direction in
which the motion is to be detected. Ensure there is no other lights which could interfere with the Sensors, imitating daylight.
SURFACE MOUNT
1. Use the L shaped arm to mark the mounting holes on the mounting surface in the desired location.
2. Drill the 2 x 8mm holes at a depth of 60mm and insert expanding anchor bolts (alternative mounting screws / plugs may
be required depending on the surface).
3. Slot the arm into the slit at the back of the Hiway fittings, replace the flat cover and secure in place with the socket
screws, washers nuts and allen key provided (nuts fit inside hexagonal cut outs on the bottom of the fitting).
4. Place the arm over the expanding anchor bolts pre-installed into the
mounting surface, followed by the washer, spring washer and then secure in
place with the nuts with a spanner, ensuring the bolts expand to lock in
place.
LAMP POST ADAPTOR
1. Remove the flat cover from the top back section of the fitting.
2. Replace with the pole adaptor (semi-circle cut out) and attach very loosely with the screws and nuts provided (nuts fit
inside hexagonal cut outs on the bottom of the fitting).
3. Slot the pole adaptor and fitting over the right-angled pole until it is in the desired location and securely fasten in place
by completely tightening the socket screws with the allen key provided.
NOTE: In order to prevent the hexagonal nuts from dropping out when removing the bolt, they are designed to remain inside
the hexagonal cut outs of the fitting. To remove, loosely screw the bolt into the nut from the underside to pull out.
TIP: The Hiway can be surface mounted
onto a 75mm or 100mm square post
(fence posts). Posts are best concreted
300-400mm into the ground.
MODES / SETTINGS:
The Hiway is an auto-adjust, multifunction solar light. All modes will only function during darkness / dusk. The on button only
needs to be pressed once for the auto-adjust multifunction to work continuously every night.
FIRST 5 HOURS: Constant on at 30% brightness. Full brightness when motion is detected within 8 metres. After 20 seconds
of no motion being detected, the light will reduce back to constant light at 50% brightness.
AFTER 5 HOURS OR LESS THAN 30% BATTERY CAPACITY –Full brightness when motion is detected within 8
metres. Following 20 seconds of no movement being detected, the light will reduce to 50% brightness.
After 5 minutes, the light will turn off until movement is detected again.
ON/OFF: Press the button next to the PIR Sensor once to turn on (auto adjust), and again to turn off
completely.