LUMENWERX AXLE User manual

+
*
POWER SIDE
NON-POWER SIDE
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC. FILE NAME:AXLE-WALL-MOUNT-INST November 8, 2019 Page: 1 / 5
LumenWerx ULC. reserves the right to change or modify product specifications without notification
WALL MOUNT - INSTALLATION INSTRUCTIONS
WWW.LUMENWERX.COM
AXLE
NOTE: Wire dimming conductors as Class 1
1
4
2
5 6
3
SINGLE FIXTURE
Locate junction box and mounting points on the
wall, according to the dimensions in the supplied
client drawing.
Secure the fixture’s arm (B) with provided screws
(C). Repeat on both sides.
Make sure that the power cable coming from the
fixture’s end cap (A) is passing through the fixture’s
arm (B). Install the fixture’s arm (B) on the end cap
(A).
Determine what orientation the fixture should be
before attaching the arm to the fixture.
Install the fixture’s arm (B) on the end cap (A).
Make electrical connexion between fixture (D) and
junction box (E), inside the junction box (connect
the same color wires together).
Indirect light
Direct light
A
A
B
BC
E
D
B

+
*
lens
tool
WWW.LUMENWERX.COM
7
10
8
11
9
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC. FILE NAME:AXLE-WALL-MOUNT-INST November 8, 2019 Page: 2 / 5
LumenWerx ULC. reserves the right to change or modify product specifications without notification
WWW.LUMENWERX.COM
12
WALL MOUNT - INSTALLATION INSTRUCTIONS
AXLE
POWER SIDE
CONTINUOUS SYSTEM
NON-POWER SIDE
Screw the arm mounting plate (F) to the junction
box (E) (screws supplied by others).
Screw the arm mounting plate (F) directly to the
wall, using drywall screws (by others); and drywall
anchors (by others) when needed.
Push the cover plate (G) to the fixture’s arm
mounting plate and fix it using set screws (H) (6/32
Alan key needed). The set screws (H) should be
flush with the cover plates (G). Repeat on both
sides.
Install the first fixture as shown in steps 3 to 9.
Locate junction box and mounting points on the
wall, according to the dimensions in the supplied
client drawing. Determine what orientation the
fixture should be before attaching the arm to the
fixture, as shown in step 2.
Remove the lens (I) from the second fixture with
the included lens tool.
I
F
F
G
G
E
H
H

WWW.LUMENWERX.COM
13
16
14
17
15
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC. FILE NAME:AXLE-WALL-MOUNT-INST November 8, 2019 Page: 3 / 5
LumenWerx ULC. reserves the right to change or modify product specifications without notification
WWW.LUMENWERX.COM
18
WALL MOUNT - INSTALLATION INSTRUCTIONS
AXLE
K
Install the second fixture’s arm (B) on the end cap
(A).
Secure the second fixture’s arm (B) with provided
screws (C).
Unscrew and remove the end cap covers (J) on
both sides of the second fixture. Place them in a
safe place.
Disconnect LED molex connectors (K) by taking a
pointed object and pressing on the two tabs on the
top. Then remove the reflector (L) from the fixture
and place it in a safe place.
Pass the wires from the first fixture inside the
second fixture. Align the joiners (M) at the end
of the first two fixtures (D) and (N) and connect
them.
Connect joiners (M) together using provided
screws.
LJ
N
D
M
M
A
B
B
C

Replace the wires protector (F) to the fixture.
Remove the wires protector (F) from the fixture.
WWW.LUMENWERX.COM
19
22
20
23
21
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC. FILE NAME:AXLE-WALL-MOUNT-INST November 8, 2019 Page: 4 / 5
LumenWerx ULC. reserves the right to change or modify product specifications without notification
WWW.LUMENWERX.COM
24
WALL MOUNT - INSTALLATION INSTRUCTIONS
AXLE
H
H
Connect wires between joining fixtures using
quick connectors (O) (connect the same color
wires together).
Push the cover plate (G) to the fixture’s arm
mounting plate and fix it using set screws (H) (
6/32 Alan key needed). The set screws (H) should
be flush with the cover plates (G).
Screw the arm mounting plate (F) directly to the
wall, using drywall screws (by others); and drywall
anchors (by others) when needed.
Reconnect LED molex connectors (K) to the
reflector (L). Reinstall the reflector (L).
O
G
G
FF
L
K
L
F

WWW.LUMENWERX.COM
25 26
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC. FILE NAME:AXLE-WALL-MOUNT-INST November 8, 2019 Page: 5 / 5
LumenWerx ULC. reserves the right to change or modify product specifications without notification
WWW.LUMENWERX.COM
WALL MOUNT - INSTALLATION INSTRUCTIONS
AXLE
Screw back in place the end cap cover (J) to keep
the reflector in place. Put back in place the lens (I).
J
I