LUMENWERX CANYON User manual

NOTE: Wire dimming conductors as Class 1
SINGLE FIXTURE
CONTINUOUS SYSTEM
G
Unscrew and remove the top cap (G). Place it in a
safe place.
A
A
B
B
B
AA
EE
D
CC
A
F
Pass the electrical wires throught the wall bracket
(A) and junction cover (C) and make electrical
connection between fixture (D) and junction box
(E).
Unscrew and remove wall bracket (A) from
fixture bracket (B).
Unscrew and remove wall bracket (A) from
fixture bracket (B). Put it in a safe place.
Screw back the junction cover (C) on the junction
box (E) and then screw the wall bracket (A) to the
wall using anchors.
Insert fixture bracket (B) into wall bracket (A) and
secure in place with supplied screws (F). Do not
overtighten.
WALL MOUNT - INSTALLATION INSTRUCTIONS
WWW.LUMENWERX.COM
CANYON
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC. FILE NAME:CANYON-WALL-MOUNT-INST November 10, 2019 Page: 1 / 4
LumenWerx ULC. reserves the right to change or modify product specifications without notification
1
4
2
5 6
3

Disconnect LED molex connector (I) by taking a
pointed object and pressing on the two tabs on the
top.
I
I
H
Remove dust cover (H) from all the fixtures in the
run except the first one connected to power.
A
E
D
C
A
E
C
Unscrew the side reflector (J) on the second
fixture on the power side and remove it. Place
the side reflector (J) in a safe place. Repeat for all
fixtures in the run.
Insert the first fixture bracket (B) into wall bracket
(A) and secure in place with supplied screws (F). Do
not overtighten.
J
Pass the electrical wires throught the wall bracket
(A) and junction cover (C) and make electrical
connection between the first fixture (D) and
junction box (E).
Screw back the junction cover (C) on the junction
box (E) and then screw the wall brackets (A) to the
wall using anchors.
B
A
F
WALL MOUNT - INSTALLATION INSTRUCTIONS
WWW.LUMENWERX.COM
7
10
8
11
9
12
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC. FILE NAME:CANYON-WALL-MOUNT-INST November 10, 2019 Page: 2 / 4
LumenWerx ULC. reserves the right to change or modify product specifications without notification
CANYON

N
K
D
L
M
G
M
Reconnect LED molex connector (H) to the side
reflector (I). Reinstall the side reflector (I).
Screw top cap (G) on top of the the joiners. Repeat
steps 13 to 17 for all other fixtuers in the run. Tighten
all screws on mounting brackets.
Connect wires between joining fixtures using quick
connectors (N).
Secure the two fixtures (D) and (L) by fastening
set screws (M) on the joiners (K).
I
J
Insert the second fixture (L) bracket (B) into wall
bracket (A), and secure in place with supplied
screws (F). Do not overtighten.
BL
A
F
D
L
K
K
Pass the wires from the first fixture inside the
seconf fixture. Align the joiners (K) at the end of
the first two fixtures (D) and (L) and connect them.
WALL MOUNT - INSTALLATION INSTRUCTIONS
WWW.LUMENWERX.COM
13
16
14
17
15
18
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC. FILE NAME:CANYON-WALL-MOUNT-INST November 10, 2019 Page: 3 / 4
LumenWerx ULC. reserves the right to change or modify product specifications without notification
CANYON

Reinstall dust cover (H) back in place.
H
WALL MOUNT - INSTALLATION INSTRUCTIONS
WWW.LUMENWERX.COM
19
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC. FILE NAME:CANYON-WALL-MOUNT-INST November 10, 2019 Page: 4 / 4
LumenWerx ULC. reserves the right to change or modify product specifications without notification
CANYON