LUMENWERX VIA 2 User manual

SINGLE FIXTURE
CONTINUOUS SYSTEM
F
Remove the lenses (F) of all the fixtures in the run
with the included lens tool. If direct/indirect or
indirect, also remove the top lenses.
G
Disconnect LED molex connector (G) by taking a
pointed object and pressing on the two tabs on the
top.
G
H
Remove all the end LED cartridges (H). If direct/
indirect or indirect, also remove the top cartridge .
Lens
Tool
WWW.LUMENWERX.COM
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC. FILE NAME:VIA2-WALL-MOUNT-INST November 15, 2019 Page: 1 / 3
LumenWerx ULC. reserves the right to change or modify product specifications without notification
WALL MOUNT - INSTALLATION INSTRUCTIONS
VIA 2
NOTE: Wire dimming conductors as Class 1
1
4
2
5
3
6
Make wire connection between fixture (B) and
wall power cable (C). Number of wires may vary.
Insert fixture bracket (D) into wall bracket (A), and
secure in place with suplied screws (E).
A
B
AC
A
E
D
SIDE VIEW
Locate wall bracket position using provided client
drawing. Install mounting brackets (A) to wall.
Align with structural stud (need double studs –
distance between screws is 1.250”) or use metal
anchors with min. length 1.250”. Flat head Philips
drive screw, nominal size #10, min. length 1.250”.

A
A
SIDE VIEW
Insert the first fixture bracket (D) into wall bracket
(A), and secure in place with suplied screws (E).
Insert the second fixture bracket (D) into wall
bracket (A), and secure in place with suplied
screws (E). Do not overtighten.
A
A
E
E
D
D
Locate wall bracket position for the second fixture
using provided client drawing. Install mounting
brackets (A) to wall. Align with structural stud
(need double studs – distance between screws
is 1.250”) or use metal anchors with min. length
1.250”. Flat head Philips drive screw, nominal size
#10, min. length 1.250”.
I
J
I K
Remove the screw (I) on the joiner and put it in a
safe place.
Connect wires between joining fixtures using quick
connectors (J). Number of wires may vary.
Join fixtures using align pins as guide. Put back in
place the provided screw (I) (using 3/16” Ball-End
Screwdriver (K) provided). Make sure that no wires
are placed in between the extrusions, preventing
the fixtures to be joined. Tight the screw (I) to pull
the extrusions together.Repeat steps 9 to 12 for all
other fixture. Then tighten all screws on mounting
brackets.
WWW.LUMENWERX.COM
789
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC. FILE NAME:VIA2-WALL-MOUNT-INST November 15, 2019 Page: 2 / 3
LumenWerx ULC. reserves the right to change or modify product specifications without notification
10 11 12
WALL MOUNT - INSTALLATION INSTRUCTIONS
VIA 2

DIRECT/INDIRECT
L
H
Reinstall the cartridge (H) and reconnect the LED
molex connector (G). NOTE: connect black wire
into the negative (-) terminal and the white wire
into (+) positive terminal. Make sure that the wires
are not hiding any LED diode. Screw the cartridge
back in place.
G
F
Put the lenses (F) back in place.
Secure the top joiner (L) with screws. Repeat
on both sides.
WWW.LUMENWERX.COM
13 14 15
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC. FILE NAME:VIA2-WALL-MOUNT-INST November 15, 2019 Page: 3 / 3
LumenWerx ULC. reserves the right to change or modify product specifications without notification
WALL MOUNT - INSTALLATION INSTRUCTIONS
VIA 2