Lumina DUO User manual

LUMINA DUO Timer
Display
Selecting the mode and connecting the sensor
Wiring diagram
The LUMINA DUO shutter and blinds controller provides you with unique opportunities fo
r
adapting the functions to your own requirements. There are two different modes
available:
1. DUOMATIC (delivery mode).
Daily programme (same UP and DOWN times every day, holiday programme, inching
mode, summertime/wintertime changeover, floating contact, terminals for sunlight/twilight
sensor.
You can choose from 3 modes:
man Manual control
Automatic 1 (daily programme)
Automatic 1 + Random
Hold the mode button for longer than 2 seconds to scroll through possible function modes
in seconds.
2. LUMINA
Two weekly programmes (up to 2 UP and DOWN times per day), inching mode, holida
y
programme, summertime/wintertime changeover, floating contact, terminals fo
r
sunlight/twilight sensor.
Seven modes are available:
man Manual control
Automatic 1 (weekly programme 1)
Automatic 2 (weekly programme 2)
Automatic 1 + 2
Automatic 1 + Random
Automatic 2 + Random
Automatic 1 + 2 + Random
Selecting the mode and connecting the sensor
The controller is delivered with the factory setting Duomatic mode. The SD slot for the
sunlight/twilight sensor is filled with a connector and a wire jumper. To change the
controller over to the Lumina mode pull the connector out or remove the jumper at the
connector (see the illustration).
The timer can also be changed over when the sunlight/twilight sensor is used. Removing
the jumper does not affect the sunlight/twilight function and serves only to set the mode.
Manual mode
Holding a direction button longer than 1 s. sets the shutters in motion; they stop when the
button is pressed again. The sunlight and twilight settings have no effect in the Manual
mode.
Automatic mode
In the Automatic mode the shutters are raised or lowered automatically at pre-
programmed switching times and taking account of the sunlight/twilight settings (where an
SD sensor is connected). In addition, manual operations are possible at any time using the
direction buttons. This does not cause the system to leave the Automatic mode.
Switchover MAN – AUTO
Where required you can switch between Manual and Automatic mode at any time b
y
pressing the mode button.
Random generator (holiday switching)
Random - this mode moves the programmed Down or Up times back on a random
basis by 1-31 minutes. With this "holiday switching" option your house looks as if it is
occupied in your absence.
Inching mode
Touch the direction buttons (about 1 s.) to slant the blind slats. The system remains in the
A
utomatic mode.
EMERGENCY STOP safety function
If the connected tube motor is stopped manually by pressing a button (AP/DOWN/Mode)
when an automatic UP or DOWN command is being carried out, the controller jumps
automatically to the Manual mode (man). This EMERGENCY STOP function ensures that
every automatic move command can be stopped at any time in cases of danger b
y
pressing any button and that no additional move commands can be carried out that are
triggered automatically (e.g. through switching times or sensor commands). Press the
mode button to reactivate the Automatic mode.
Sunlight function (SD sensor required)
The controller detects the insertion or removal of the sensor automatically after a fe
w
seconds. The item "Sunlight sensor" is therefore released or blocked in the programming
menu with the "Sun" symbol. In this menu item you can switch the controller's sunlight
function on and off or recalibrate the brightness value. The calibration takes over the
current brightness as the brightness limit value. If the preset brightness is exceeded, this is
acknowledged immediately in the timer's display with the "Sun" symbol. If the preset
brightness is exceeded for 10 minutes, the shutter moves down to the sensor. The
shutter's position is checked in addition every 60 minutes on the basis of the changing
angle of incidence. If the actual brightness value falls below the preset brightness value,
the "Sun" symbol disappears from the display. If the actual value remains below the preset
brightness value for 10 minutes, the shutter moves up again accordingly. The sunlight
function is only active in the Automatic 1 mode.
Twilight function (SD sensor required)
The programming item "Twilight function" with the "Moon" symbol is released as soon as
an SD sensor is connected. The operator can switch the twilight function on and off o
r
recalibrate the twilight value. The calibration takes over the current brightness as the
twilight limit value. The twilight mode is only active in Automatic 1 mode after a preset
down move time. If the actual value falls below the preset twilight value, this is
acknowledged immediately in the timer's display with the "Moon" symbol. If the actual
value remains below the preset twili
g
ht value for 10 minutes, the shutter moves down.
Note: floating contacts
The factory-installed jumper (L) to L can be removed where
required. The controller then switches floating between (L) and UP
or DOWN.
Technical data
Nominal operating voltage: 230 V / 50 Hz
Switching voltage: 250 V AC
Switching contact load: max. 6 A at cos phi=1
Operating temperature range: -5°C to 45°C
Travel time: max. 2.5 min.
Power reserve: min. 8 hrs.
Degree of protection: IP 40
Safety class: II
Conformity: CE
DUOMATIC
(with jumper)
LUMINA
(without jumper)

Settings Lumina Mode Display
Setting the time
Hold Set button longer than 2 seconds Automatic symbol blinks
Use the arrow buttons to select time symbol Time symbol blinks
Press the Set button to confirm W or So symbol blinks
Select summertime (So)/wintertime (W) with the arrow buttons W or So symbol blinks
Press the Set button to confirm Weekday blinks
Set the day with the arrow buttons Weekday blinks
Press the Set button to confirm Time blinks
Set the time with the arrow buttons New time blinks
Press the Set button to confirm Time symbol blinks
Select the exit (door symbol) with the arrow buttons Door symbol blinks
Press the Set button to confirm exit from programming Time/day displayed
Switchover wintertime/summertime
Hold Set button longer than 2 seconds Automatic symbol blinks
Use the arrow buttons to select time symbol Time symbol blinks
Press the Set button to confirm W or So symbol blinks
Select summertime (So)/wintertime (W) with the arrow buttons W or So symbol blinks
Press the Set button to confirm Weekday blinks
Press the Set button to confirm Time blinks
Press the Set button to confirm Time symbol blinks
Select the exit (door symbol) with the arrow buttons Door symbol blinks
Press the Set button to confirm exit from programming Time/day displayed
Setting weekly programme 1
Hold Set button longer than 2 seconds Automatic symbol blinks
Press the Set button to confirm All weekdays blink *
Use the arrow buttons to select the desired weekday Weekday blinks
Press the Set button to confirm Move up time blinks
Use the arrow buttons to set the move up time Set move up time blinks
Press the Set button to confirm Move down time blinks
Use the arrow buttons to set the move down time Set move down time blinks
Press the Set button to confirm Weekday blinks
Use the arrow buttons to set the next weekday Weekday blinks
...set additional days as described (from *)...
...then Weekday blinks
Use the arrow buttons to select the END symbol END symbol blinks
Press the Set button to confirm Automatic symbol blinks
Use the arrow buttons to select the exit (door symbol) Door symbol blinks
Press the Set button to confirm exit from programming Time/day displayed
* TIP: Instead of a defined weekday, use the ALL option to select all weekdays
and where required program them with the same switching times.
Setting weekly programme 2
Hold Set button longer than 2 seconds Automatic symbol blinks
Use the arrow buttons to select symbol 2 (Automatic 2) Symbol Automatic 2 blinks
Press the Set button to confirm All weekdays blink
...Continue as with weekly programme 1...
Switch sunlight function on/off (where sensor fitted)
Hold Set button longer than 2 seconds Automatic symbol blinks
Use the arrow buttons to select the sun symbol Sun symbol blinks
Press the Set button to confirm ON or OFF blinks
Use the arrow buttons to select ON or OFF ON or OFF blinks
Press the Set button to confirm Sun symbol blinks
Use the arrow buttons to select the exit (door symbol) Door symbol blinks
Press the Set button to confirm exit from programming Time/day displayed
Calibrate brightness value (where sensor fitted)
Hold Set button longer than 2 seconds Automatic symbol blinks
Use the arrow buttons to select the sun symbol Sun symbol blinks
Press the Set button to confirm ON or OFF blinks
Use the arrow buttons to select EICH (CALIBRATE) EICH blinks
Press the Set button to confirm Sun symbol blinks
Use the arrow buttons to select the exit (door symbol) Door symbol blinks
Press the Set button to confirm exit from programming Display: Time/day/sun
Switch twilight function on/off (where sensor fitted)
Hold Set button longer than 2 seconds Automatic symbol blinks
Use the arrow buttons to select the moon symbol Moon symbol blinks
Press the Set button to confirm ON or OFF blinks
Use the arrow buttons to select ON or OFF ON or OFF blinks
Press the Set button to confirm Moon symbol blinks
Use the arrow buttons to select the exit (door symbol) Door symbol blinks
Press the Set button to confirm exit from programming Time/day displayed
Calibrate twilight value (where sensor fitted)
Hold Set button longer than 2 seconds Automatic symbol blinks
Use the arrow buttons to select the moon symbol Moon symbol blinks
Press the Set button to confirm ON or OFF blinks
Use the arrow buttons to select EICH (CALIBRATE) EICH blinks
Press the Set button to confirm Moon symbol blinks
Select the exit (door symbol) with the arrow buttons Door symbol blinks
Press the Set button to confirm exit from programming Display: Time/day/moon
Select mode
Hold Mode button for longer than 2 seconds
All 7 modes are scrolled
through automatically one after
the other,
release the Mode button at the
desired mode.
Settings Duomatic Mode Display
Setting the time
Hold Set button longer than 2 seconds
A
utomatic symbol blinks
Use the arrow buttons to select time symbol Time symbol blinks
Press the Set button to confirm W or So symbol blinks
Select summertime (So)/wintertime (W) with the arrow buttons W or So symbol blinks
Press the Set button to confirm Time blinks
Set the time with the arrow buttons New time blinks
Press the Set button to confirm Time symbol blinks
Select the exit (door symbol) with the arrow buttons Door symbol blinks
Press the Set button to confirm exit from programming Time blinks
Switchover wintertime/summertime
Hold Set button longer than 2 seconds
A
utomatic symbol blinks
Use the arrow buttons to select time symbol Time symbol blinks
Press the Set button to confirm W or So symbol blinks
Select summertime (So)/wintertime (W) with the arrow buttons W or So symbol blinks
Press the Set button to confirm Time blinks
Press the Set button to confirm Time symbol blinks
Select the exit (door symbol) with the arrow buttons Door symbol blinks
Press the Set button to confirm exit from programming Time blinks
Setting the switching times
Hold Set button longer than 2 seconds
A
utomatic symbol blinks
Press the Set button to confirm Move up time blinks
Use the arrow buttons to set the move up time Set move up time blinks
Press the Set button to confirm Move down time blinks
Use the arrow buttons to set the move down time Set move down time blinks
Press the Set button to confirm
A
utomatic symbol blinks
Use the arrow buttons to select the exit (door symbol) Door symbol blinks
Press the Set button to confirm exit from programming Time blinks
Switch sunlight function on/off (where sensor fitted)
Hold Set button longer than 2 seconds
A
utomatic symbol blinks
Use the arrow buttons to select the sun symbol Sun symbol blinks
Press the Set button to confirm ON or OFF blinks
Use the arrow buttons to select ON or OFF ON or OFF blinks
Press the Set button to confirm Sun symbol blinks
Use the arrow buttons to select the exit (door symbol) Door symbol blinks
Press the Set button to confirm exit from programming Time blinks
Calibrate brightness value (where sensor fitted)
Hold Set button longer than 2 seconds
A
utomatic symbol blinks
Use the arrow buttons to select the sun symbol Sun symbol blinks
Press the Set button to confirm ON or OFF blinks
Use the arrow buttons to select EICH (CALIBRATE) EICH blinks
Press the Set button to confirm Sun symbol blinks
Use the arrow buttons to select the exit (door symbol) Door symbol blinks
Press the Set button to confirm exit from programming Time blinks
Switch twilight function on/off (where sensor fitted)
Hold Set button longer than 2 seconds
A
utomatic symbol blinks
Use the arrow buttons to select the moon symbol Moon symbol blinks
Press the Set button to confirm ON or OFF blinks
Use the arrow buttons to select ON or OFF ON or OFF blinks
Press the Set button to confirm Moon symbol blinks
Use the arrow buttons to select the exit (door symbol) Door symbol blinks
Press the Set button to confirm exit from programming Time blinks
Calibrate twilight value (where sensor fitted)
Hold Set button longer than 2 seconds
A
utomatic symbol blinks
Use the arrow buttons to select the moon symbol Moon symbol blinks
Press the Set button to confirm ON or OFF blinks
Use the arrow buttons to select EICH (CALIBRATE) EICH blinks
Press the Set button to confirm Moon symbol blinks
Use the arrow buttons to select the exit (door symbol) Door symbol blinks
Press the Set button to confirm exit from programming Time blinks
Select mode
Hold Mode button for longer than 2 seconds
A
ll 3 modes are scrolled
through automatically one after
the other,
release the Mode button at the
desired mode.
ATTENTION: Installation work on the 230 V supply may only be carried out by authorised electricians!
RESET / Delivery status
Press the RESET button to reset the input values to the factory setting:
Duomatic mode:
Daily programme UP 07.00, DOWN 21.00
Sun function ON (if sensor fitted,
calibrated to an average value)
Twilight function ON (if sensor fitted,
calibrated to an average value)
Time Wintertime, 20.00
Lumina mode:
Weekly programme 1 UP 07.00, DOWN 21.00
Weekly programme 2 UP OFF, DOWN OFF
Sun function ON (if sensor fitted;
calibrated to an average value)
Twilight function ON (if sensor fitted;
calibrated to an average value)
Time Wintertime, Monday, 20.00