LUMINELL SL1 Instruction Manual

Version 1.0 20200316
BY LUSEARCHLIGHT SYSTEM
BY LUMINELL
INSTALLATION & USER'S MANUAL
V1.1_18-09-2020

LUMINELL SWEDEN AB 2
Dear Customer.
Thank you for choosing a searchlight from Luminell.
Our products are assembled in Sweden by a dedicated team of technicians and the
components we use are chosen with highest focus on both performance and quality.
We hope that you will be totally satisfied with your searchlight.
If you have a question or if there is a problem with the product, please don't hesitate to
contact our support team in Sweden.
Luminell Sweden AB
Service & Technical Support
[e-mail]
Phone: [phone]
All information in this manual was correct at time of publication. However, as our engineers
are always updating and improving our products, your system's software might provide a
slightly different appearance or modified functionality than presented in this manual.
If your system lacks any function presented in this manual, there is possibly a software
update available to resolve this, please contact Luminell for more information.
All rights reserved. No part of this publication may be reproduced, distributed, or transmitted
in any form or by any means, including photocopying, recording, or other electronic or
mechanical methods without the prior permission from Luminell Sweden AB.
For permission requests, contact us at the address: [e-mail]
COPYRIGHT LUMINELL © 2020. All rights reserved

LUMINELL SWEDEN AB 3
DISCLAIMER
This manual contains important information for both installer and end user.
Read the manual carefully before installing or using your new searchlight and keep the
manual close to the user as a future reference document.
With new firmware updates come new features that are not currently described in this
manual, for the latest firmware and manual update information see Luminell's website
https://luminell.com/products/searchlights/clite1-searchlight/

LUMINELL SWEDEN AB 4
Document versions
Approvals
This document requires following approvals:
Date
Version
Document Changes
Required
firmware
pack
19-11-2019
0.1
Initial draft
Beta 1
16-03-2020
1.0
Release 1
1.0
18-09-2020
1.1
Firmware update added, other minor changes
1.0
Name
Title
Anders Holst
Technical manager - Luminell Sweden AB
Joel Ekbom
Project Manager & Product Developer - Luminell Sweden AB
Mattias Svensson
Managing Director –Luminell Sweden AB
Aprovals
Title
Written by:
Reviewed and approved by:
Reviewed and approved by:
Anders Holst
Joel Ekbom
Mattias Svensson

LUMINELL SWEDEN AB 5
Table of Contents
Connection example 1 (default) –24Vdc 24

LUMINELL SWEDEN AB 6
Connection example 2 –24Vdc 25
Connection example AC using an external PSU (optional) 26
1xSL1 and 2xOperator panels 27
2xSL1 and 1xOperator panels 28
Light dim level 35
Light beam angel 36
Change the function shortcuts on the homescreen 38
Set fixed position 39
Modify sweep 40
Modify surveillance 42
Switch system 42
Park all 42

LUMINELL SWEDEN AB 7
APPENDIX 1 EMC
APPENDIX 2 Orgalime S2012; General conditions for the supply of mechanical,
electrical and electronic products.

1 WARRANTY CONDITIONS SL1
Version 1.0 20200316
WARRANTY CONDITIONS SL1
Luminell General Terms and Conditions can be found on our website www.luminell.com.
These terms govern the contractual relationships between Luminell and the Purchaser.
In the event of any conflict between this document and our General Terms and Conditions,
the General Terms and Conditions shall take precedence.
Warranty period
LUMINELL offer a warranty for the following products:
- LED-based lamps: warranty period: 60 months
- HMI-based lamps: warranty period: 24 months
- Spare parts: warranty period: 12 months
Warranty period starts from the date the goods is shipped from LUMINELL factory.
Product specific conditions
A correctly installed searchlight system from Luminell requires no planned regular
maintenance or service other than regular cleaning and care during the first 10 years of
operation.
The “Preventive maintenance”plan describes how to keep the product in good condition.
The warranty is conditioned by below mentioned key points.
Before powering up the unit, make sure that:
The mechanical fundament where the searchlight is placed is robust.
Outgoing cable radius from the searchlight is smooth and not stressed.
Ethernet cable not placed together with high power cables.
Electrical connections are made according to electrical scheme and wiring diagram.
Length of cables are not exceeding the recommended maximum lengths as stated
below:
•Power cables between searchlight and E-box for 24 VDC-system: Max 7 meter
•Remote cable / Ethernet cable between E-box and remote control: Max 100 meter
(longer distance requires an amplifier or fibre optic version).
The remote panel (OP) is bridge mounted in an IP56 environment. If placed outside, it
must be under a protection hood when not in use.
After above checkpoints are verified the system should be started up as per this
manual to verify the functionalities.
In case of any questions related to the warranty, please contact us at
[e-mail] for additional support.

2 System identification
LUMINELL SWEDEN AB 9
SYSTEM IDENTIFICATION
FINDING AND RECORDING THE SERIAL NUMBERS
For all support and service requests you will be asked for the product serial number.
Please locate the model plates on the equipment and write down the serial numbers to the
fields on the right for future use. You can locate the plate by the pictures below.
SL1
SL1 Operator panel
Sn SL1: _______________
Date: _______________
HW ver: _______________
Sn SL1-OP: _______________
Date: _______________
HW ver: _______________

3 PREFACE
LUMINELL SWEDEN AB 10
PREFACE
SHORT PRESENTATION OF SL1
Luminell sweden AB manufactures professional marine searchlights and has done so since
the early 90's.
The SL1 is a compact and extremely powerful LED searchlight with wave-compensated
movement, hold light direction and digital controlled spot / flood light beam.
Developed for and targeting Civil/Naval High Speed and Light Craft as well as Yachts. Built
to last with same quality standards as the bigger sisters but in a more compact format.
Performance, ease of use, quality and design are combined into an extremely robust unit
with innovative technology that sets a new standard for LED-searchlight of this size.
DESCRIPTION OF THE USER
This manual contains application and functionality descriptions and lists function blocks,
electrical diagrams, input and output signals, setting parameters and technical data.
The manual can be used as a technical reference during the engineering phase, installation
and commissioning phase, and during normal use.

3 PREFACE
LUMINELL SWEDEN AB 11
EXPLANATION OF SAFETY WARNINGS AND OTHER
SYMBOLS
Throughout this manual the following symbols are used to indicate where special
operator/installer attention is required, the symbols and their meanings are explained below.
Danger indicates a hazard with a high level of risk which, if not avoided, will
result in death or serious injury.
Warning indicates a hazard with a medium level of risk which, if not avoided,
could result in death or serious injury.
Caution indicates a hazard with a low level of risk which, if not avoided, could
result in minor or moderate injury.
Notice indicates installation, operation, or maintenance information that is NOT HAZARD
RELATED.

3 PREFACE
LUMINELL SWEDEN AB 12
OBTAINING DOCUMENTATION AND INFORMATION
Internet
This manual is also available as a digital PDF file.
The latest version of the documentation is available at the following address:
https://luminell.com/downloads
Ordering Documentation
Documentation, user instructions and other technical information can be ordered by mailing
[e-mail] or call [phone]
Documentation Feedback
If you want to give us documentation feedback, please follow the link below and fill in the
form.
https://www.luminell.com/product-service-request
We appreciate your comments.

4 Technical Data
LUMINELL SWEDEN AB 13
TECHNICAL DATA
SL1
Technical Data SL1
Input
Nominal voltage
24VDC (20...28VDC)
Power consumption in operation
Max 500W
Power consumption in standby
mode (light off)
5W
Current at 24V
Max 20,8A
Installation
Mounting position
- Standing (default factory setting)
- Hanging (see manuals “Installation Menu Settings”)
Electrical interface to vessel
- DC power 3 wires (+/-/earth) (see drawing on page XX for
details)
- Ethernet to operator control panel or switch (if any)
Mechanical interface to vessel
- 4 x threaded rod M8 in the searchlight base
- Sealing between vessel and searchlight mechanical hub for
galvanic insulation (and to avoid water ingress in wheelhouse)
Light performance
Spot beam
3.5°/ 1 800 kCd / 1340 m
Wide beam
15 °/ 420 kCd / 12 000 lm
Initial luminous flux
Over 30 000 lm
CRI
Min. 70
Color temp
6000 K
Start-up
System boot time
(from power off)
≈30 sec (searchlight homing procedure)
Environmental
Operating ambient temperature
-40ºC to +55ºC
Storage temperature
-25°C to +70°C
IP class
IP66/67
Vibration
Designed for IEC 60945
Shock
Designed for IEC 60945
Dimensions & weight
Static size
19 x 40 x 42 cm (see drawing on page XX for details)
Weight
18 kg
Materials & Colors
Body / casing
Seawater resistant; casted, anodized, and powder coated aluminum
Base, bolts
Stainless steel AISI 316L (1.4404), A4
Glass
Tempered glass
Available Colors
- White RAL 9016 gloss level 70
- Matt Jet Black RAL 9005 gloss level 20
Pan/ tilt performance
Horizontal (Pan)
- Unlimited movement with slipring technology
- Horizontal movement max speed 33°/second
Vertical (Tilt)
- + 90°/ - 30 movement
- Vertical movement max speed 68°/second
- Wave compensation function (firmware update, scheduled Q2
2021)

4 Technical Data
LUMINELL SWEDEN AB 14
OPERATOR PANEL
Technical Data Operator Panel
Input
Nominal voltage
24VDC (20...28VDC)
Power consumption in operation
Max 10W
Power consumption in standby
mode (parked, light off)
2,2W
Current at 24V
Max 0,4A
Installation
Electrical interface to vessel
- DC power 3 wires (+/-/earth) (see drawing on page XX for details)
- Ethernet to operator control panel or switch (if any)
Mechanical interface to vessel
- 3 x threaded rod M4 in panel base
- Sealing between vessel and panel
Start-up
System boot time
(from power off)
≈30 sec (searchlight homing procedure)
Environmental
Operating ambient temperature
-20ºC to +55ºC
Storage temperature
-25°C to +70°C
IP class
IP56
Vibration
Designed for IEC 60945
Shock
Designed for IEC 60945
Dimensions & weight
Static size
19 x 40 x 42 cm (see drawing on page XX for details)
Weight
0,5kg
Materials & Colors
Body / casing
Operator panel made in PC-ABS
Base, bolts
Stainless steel AISI 316L (1.4404), A4
Electrical interface to vessel
- DC power 3 wires (+/-/earth) (see drawing on page XX for details)
- Ethernet to operator control panel or switch (if any)
Functions
Direct button functions
- Horizontal and vertical movement
- Light on/off
- Wave compensation on/off (firmware update, scheduled Q2 2021)
- Hold light direction on/off (firmware update, scheduled Q2 2021)
- Beam angle spot/flood
- Dimming step by step
Standard menu functions
- Custom home screen –set your 4 most used functions
- Up to 4 programmable fixed positions
- Sweep in horizontal direction
- Surveillance in horizontal and vertical direction
- Switch –to another potential SL1 in the network
- Sync (firmware update, scheduled Q4 2020)

4 Technical Data
LUMINELL SWEDEN AB 15
PRODUCT COMPLIANCE DATA
To be continued, check homepage for new manual version.

5 PREPARATION OF THE PRODUCT FOR USE
LUMINELL SWEDEN AB 16
1. Lift away the accessory box and put
aside.
3. With both hands grab under the LED
housing and lift the complete package
up and out of the box.
4. The foam around the base protects the
searchlight and the cables from damage
during transport and handling and can
also be used as a temporary stand.
2. Remove the protective foam from the
support arms.
PREPARATION OF THE PRODUCT FOR USE
UNPACKING THE PRODUCT AND CHECKING THE CONTENTS
The system is delivered in a cardboard box containing 1 x SL1 searchlight with 3m
powercable and 0,9m circular LAN cable mounted to the searchlight base.
Make sure the box is placed with the correct side up, see the symbols on the box.
To unpack follow the steps below:
Accessory box contains:
•1 x SL1 operator panel.
•1 x Operator powercable 3m.
•2 x Lan cables 2m circular to RJ45.
•2 x keystone adapters RJ45 to RJ45.
•1 x User and installation manual.
•1 x Quick start guide.
•1 x Warranty registration card.

5 PREPARATION OF THE PRODUCT FOR USE
LUMINELL SWEDEN AB 17
LIFTING, HANDING AND TRANSPORTING THE PRODUCT
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Etiam at porta est, et lobortis sem.
Duis imperdiet in nisl sed luctus.
To lift the product safely:
1. To be continued, check homepage for new manual version.
2. To be continued, check homepage for new manual version.
3. To be continued, check homepage for new manual version.
Storing the product
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Etiam at porta est, et lobortis sem.
Duis imperdiet in nisl sed luctus.
To store the product safely:
1. To be continued, check homepage for new manual version.
2. To be continued, check homepage for new manual version.
3. To be continued, check homepage for new manual version.
Securing the product against shocks
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Etiam at porta est, et lobortis sem.
Duis imperdiet in nisl sed luctus.
To secure the product against shocks:
1. To be continued, check homepage for new manual version.
2. To be continued, check homepage for new manual version.
3. To be continued, check homepage for new manual version.

6 Install the Product
LUMINELL SWEDEN AB 18
INSTALL THE PRODUCT
MECHANICAL
The searchlight is mounted standing or hanging in a foundation using four hex socket
threaded rods (M8x60) in its base, the threaded rods comes with the delivery along with
washers and lock nuts.
Apply Loctite 243 or equivalent on the rods and tighten firmly.

6 Install the Product
LUMINELL SWEDEN AB 19
Mechanical drawing SL1

6 Install the Product
LUMINELL SWEDEN AB 20
Mechanical drawing SL1, base measurements