Luvele Vibe LVBS1500USA User manual

LUVELE VIBE BLENDER SYSTEM
com
Instruction
Booklet
&
User Guide

Section One - Safety Instructions
Section Two - Introduction
Section Three - Features
Section Four - Key Technology
Section Five - Setup
Section Six - Controls
Section Seven - Tips
Section Eight - Cleaning
Section Nine - Troubleshooting
Section Ten - Warranty
P3
Table of Contents
Congratulations
on the purchase of your new Luvele Vibe Blender System
Page 4 to 6
Page 7
Page 8 to 11
Page 12 to 15
Page 16 to 17
Page 18 to 22
Page 23 to 24
Page 24
Page 26
Page 27
Luvele Vibe Blender System
Voltage: 220-240 V
Frequency: 50 - 60 Hz
Watts: 1500 W
Height (with 2-litre PE Jug on base): 50 cm
Width: 20 cm
Depth: 27 cm
LVBS1500AUS / LVBS1500UK / LVBS1500EU
Voltage: 110 V
Frequency: 50 - 60 Hz
Watts: 1500 W
Height (with 2-litre PE Jug on base): 50 cm
Width: 20 cm
Depth: 27 cm
LVBS1500USA (USA model)
For the best experience we recommend that you read the instruction booklet from start to
finished before using your new Luvele Vibe Blender

Please read all instructions before using the Luvele Vibe Blender System.
Keep these instructions for future reference.
• Remove all packaging before using your Luvele Blender for the first time.
• Do not place Blender near the edge of a bench or table during operation.
• Ensure the surface is level, free of liquids or other substances.
• Do not place your Blender on or near a hot stove or oven.
• Do not immerse the blender base in water or other liquids.
• Do not place any parts of the blender in a dishwasher or microwave oven.
• Do not put your hands or utensils into the jug while blending to avoid personal injury or damage
to the machine.
• Never leave an operating blender unattended. Switch the blender off when you are away from it.
• WARNING: The blades on the Luvele blender are very sharp, please be careful during operation.
• Never touch or move the blade when the jug is on the blender base.
• Do not use the machine if the blade has come loose or is damaged in any way. Contact Luvele for
spare parts.
• WARNING: Do not remove the jug lid to use the tamper. To use tamper open the centre lid plug in
the middle of the main jug lid. Insert tamper to use.
• Do not overload the machine. Ingredients should not exceed the ‘MAX’ line near the top of the
jug. When producing a thick mixture, reduce volume accordingly.
• Always operate the machine with the lid plug firmly in place. Only remove the lid plug to add
ingredients or to use the tamper.
• When blending dry ingredients or producing nut butters & oil based foods, very high
temperatures can be generated due to the rotation speed of the blades.
Therefore, dry & oil based foods should not be processed for more than 1 minute after ingredients
have been fully blended to avoid dangerous overheating.
• The machine needs no special maintenance other than cleaning after each use. If any repairs are
needed, please contact Luvele. Never try to repair the machine without permission.
• Use a fire blanket only to extinguish fires on appliance.
ATTENTION: When operating the machine for the first time, the blender may emit an
unpleasant smell. This is normal and the smell will disappear as the motor is run-in.
SECTION ONE | P5
Safety
SECTION ONE | P4
Safety
This appliance is intended to be used in household and similar applications such as:
- Staff kitchen areas in shops, offices and other working environments;
- Farm houses;
- By clients in hotels, motels and other residential type environments;
- Bed and breakfast type environments
This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for
their safety.
Children 8 years and above can use this appliance, however, they should be supervised to
ensure that they do not play with the appliance. Children should not play with the appliance.
Cleaning and user maintenance shall not be made by children unless they are older than 8 years
old and supervised.
Keep the appliance and its cord out of reach of children less than 8 years.
Check the power supply cord for damage from time to time. If the power supply cord is dam-
aged, it must be replaced by the manufacturer or its service agent or a similarly qualified person
in order to avoid a hazard. Operate appliance only through a professionally installed socket.
Never remove main cable with wet hands, or lay cable on hot surface, or let cable come into
contact with oil.
Do not operate outdoors.
Use only designated accessories enclosed and supplied by Luvele.
This appliance is not intended to be operated by means of external timer or separate
remote-control system. Supply the correct voltage and do not use extension cables.

SECTION TWO | P7
SECTION ONE | P6
WARNING: Do not attempt to remove the blender jug from the rubber centring pad while the
motor is in operation.
WARNING: Do not operate the blender base without the blender jug properly in position.
WARNING: If the ingredients stop circulating, DO NOT rock, shake or move the blender jug
while the motor is running.
WARNING: Spinning blades can cause injury. Wait until the blades have completely stopped
rotating before removing the blender jug. NEVER reach into the blender jug
while it is placed on the centring pad.
WARNING: The core plate, blades and drive socket may become very hot after
extended use. DO NOT touch. Allow to cool down before handling or cleaning.
WARNING: Do not fill the 2L PE jug or the 1.75L stainless steel jug with more than 1L (1qt) of
hot liquid.
Safety
!ATTENTION:
When operating the machine for the first time, the blender may emit an
unpleasant smell. This is normal and the smell will disappear as the
motor is run-in.
Introduction
The Luvele Vibe Blender System uniquely comes with both a 2L BPA free PE
plastic jug, as well as a 1.75L stainless steel jug, providing control and flexibility
for any blending and food processing project in the kitchen. The Luvele Vibe
Blender System has been designed with superior components and technology,
creating a world class blending system for home use.
THE LUVELE VIBE BLENDER SYSTEM IS THE ONLY BLENDER & FOOD PROCESSOR
YOU WILL NEED IN YOUR LUVELE KITCHEN.
THE GROUND BREAKING
FEATURES INCLUDE;
Smart-Touch Control Panel
Sound Elimination Technology
Medical Grade Japanese Stainless Steel Blades
German Designed Heavy Duty 1500W Motor
Temperature Sensor Control Technology
360 Quad Vortex technology
♥ ♥

SECTION THREE | P9
SECTION THREE | P8
Features Features
FILLER CAP
JUG LID
SEALING RING
JUG BODY
TEMPERATURE SENSOR PRONGS
JAPANESE STAINLESS STEEL BLADE SET
STAINLESS STEEL CORE PLATE
SOUND ELIMINATION COMPOSITE DRIVE SOCKET
TEMPERATURE SENSOR SOCKET
ALUMINIUM MOTOR SEAT
INCLUDING NON-SLIP RUBBER CENTRING PAD
INTELLIGENT ‘ONE TOUCH’ CONTROL PANEL
& LCD SCREEN
SOUND ELIMINATION BLENDER BASE
NON-SLIP RUBBER FEET & SUCTION PADS
The 1.75 litre stainless steel jug can be used
for many recipes. It is perfect for making
hot soups & drinks. The stainless steel jug
is also ideal to be used as a grain and dry
jug for grinding ingredients. The high
quality SS does not absorb odours, and will
not stain from nuts, grains and herds. The
sturdy 304 stainless steel construction is also
perfect for blending ice.
The 2 litre Jug is made from almost
unbreakable BPA free, PE plastic.
It’s great to use when you want to see
the ingresdients inside the jug and
the blending process.
MAX level for hot liquids = 1L (1qt)
MAX level for cold liquids = 1.75L (1.85qt)
MAX level for hot liquids = 1L (1qt)
MAX level for cold liquids = 2L (2.1qt)

SECTION THREE | P11
SECTION THREE | P10
Features Features
TAMPER:
!WARNING
Only use the tamper when the lid is firmly in
position and the ingredients
have stopped circulating.
The tamper allows you to accelerate the process of blending
very thick or frozen ingredients that cannot be processed
in a regular blender. Use it to help safely loosen blocked
ingredients so circulation is maintained during blending. Its
also helpful when blending nuts to help move and push the
nuts into the blade.
Remove the filler cap and insert the tamper with the lid still
firmly in place. Hold the blender jug handle with one hand
and with the other move the tamper in a circular motion, and
up and down to unblock the content of the jug.
The blender jug should not be more than two-thirds full
when the tamper is used during blending. To avoid
overheating during blending, DO NOT use the tamper for
more than 30 consecutive seconds.
ACCESSORIES ARE AVAILABLE FOR SEPARATE PURCHASE AT WWW.LUVELE.COM
OVEN MITT:
The oven mitt can be used when making
hot soups or drinks. For example, when
making a hot soup in the stainless steel
jug, the outside of the jug will get hot.
Use the oven mitt to handle & remove
the jug from the blender base.
CLEANING BRUSH:
Simply insert the bottom of the cleaning brush under the blades and rotate around the jug to
clean.
SPATULA:
Use the spatula after blending is finished
to help scoop out ingredients from jug.
ACCESSORIES ARE AVAILABLE FOR SEPARATE PURCHASE AT WWW.LUVELE.COM

SECTION FOUR | P13
SECTION FOUR | P12
Key Technology
KEY
1
KEY
2
KEY
3
KEY
4
SOUND ELIMINATION TECHNOLOGY
While there is no such thing as a silent blender, the Luvele design and engineering
team worked hard to reduce the amount of noise the Luvele Vibe Blender generates
during use. After 2 years of development, Luvele created the following key features to
eliminate as much noise as possible.
Patented air-duct technology, provides fast heat dissipation and
uniformed air extraction during operation.
High concentricity bearings, central shaft and blade set.
An efficient, high speed motor that functions with low friction levels, allows
for a highly stable motor during operation . The motor’s fixing bracket,
which holds the motor in place, has also been engineered with noise
reduction qualities.
The Luvele drive socket is made from a composite of metal and PA46.
PA46 (polyadipic succinimide) is a new type of polyamide resin with a high
melting point and high crystallinity. It provides unmatched performance for
demanding applications in which superior heat resistance, design stiffness,
wear & friction are required. It’s used in automobiles, aerospace and
military equipment. These qualities help to reduce the noise level of the
spinning blades during operation and make the drive stock on the Luvele
Vibe Blender extremely strong and long lasting.
They are constructed from highly refined
420 stainless steel, which is mold quality
stainless steel, engineered to exhibit superior
strength, strong corrosion resistance and high
wear resistance.
The blade set has been designed with a 45
degree elevation angle, which has proven to be
the most efficient way to create a strong vortex
system when blending, leading to superior
blending results.
MEDICAL GRADE JAPANESE
STAINLESS STEEL BLADES
The Luvele designed 4-leaf
stainless steel blades are made with
medical grade stainless steel
imported from Japan.
CONSTRUCTED FROM HIGHLY REFINED
420 STAINLESS STEEL
Key Technology

SECTION FOUR | P15
SECTION FOUR | P14
It produces strong torque, robust torsion
and is efficient and stable at high speeds.
This stability during operation assists to reduce the overall noise level of the blender,
allowing for a much more comfortable blending experience.
TEMPERATURE SENSOR CONTROL TECHNOLOGY
The Luvele Vibe Blender System has been designed with an accurate temperature
control system, to provide full control of blending outcomes. The temperature sensor
allows you to know what the temperature of the ingredients are in the jug at all times.
This is important when making raw food recipes, as well as making hot soups and
drinks.
The Luvele Vibe Blender will automatically turn off when 100 °C (212 °F) is reached
to protect the motor and components
Key Technology
GERMAN DESIGNED HEAVY DUTY
1500W
The German designed Luvele motor has
been constructed with a unique balance
between high speed and stability when
in use.
Key Technology
360 QUAD VORTEX TECHNOLOGY
The Luvele round jug design has four perfectly
positioned ribs inside the jar. These create an
omni-directional mixing flow, allowing for a
complete 360 degree mixing effect on the
ingredients in the jug.
Four vortexes are generated between the ribs
and rotate upward along the jug walls. They
then fall from the top to the centre of the blade,
and then form the vortexes again, in a continuous
loop. This continuous blending loop creates the
omni-directional mixing flow to comprehensively
blend ingredients.
SINGLE VORTEX DESIGN
Square jugs generally have minimal or
no ribs to create multiple vortexes. A
single vortex in therefore created by the
four right angles in the jug wall. When the
blade rotates at high speed, it forms one
huge vortex, pushing and mixing ingredients
into the four corners of the jug. This does not
create a sufficient height for the vortex.
It can cause food ingredients inside
the jug to accumulate in the four corners,
which does not allow the ingredients to
flow and blend evenly. SINGLE VORTEX DESIGN

Remove all packaging material before using your Luvele Vibe Blender for the first
time. Wash the blender jug, blades, lid cover, tamper & spatula before first use in
warm soapy water. Wipe the blender base with a damp cloth.
SECTION FIVE | P16
Setup
Now you are ready to set the controls & begin your blending cycle.
SEE FOLLOWING PAGES.
TIP:
Due to the Vibe Blender’s power & speed, processing times are much
quicker than standard blenders. Until you are accustomed to the machine, watch
the processing time carefully to avoid over processing.
When blending has been completed, press the power switch to turn OFF,
before removing the blender jug.
SECTION FIVE | P17
!ATTENTION:
When operating the machine for the first time, the blender may emit an
unpleasant smell. This is normal and the smell will disappear as the motor is run-in.
GENERAL SETUP:
STEP
1
STEP
2
STEP
5
Place the blender base on a level surface, indoors.
NOTE:
The Luvele Vibe Blender is equipped with a magnetic induction safety switch. The
jug needs to be securely placed onto the blender base so it is sitting level. The
blender will not operate unless the jug is fitted correctly.
Plug the blender into a power source.
!WARNING:
Do not operate the blender when the blender jug is
empty.
BEFORE USING YOUR VIBE BLENDER:
Setup
STEP
6
!WARNING:
Do not operate the blender
without the lid securely in position.
TIP:
Place liquids and soft foods in the
blender jug first, followed by solid
items & ice last.
Add the ingredients to the blender jug and ensure that the ingredients do
not exceed the ‘MAX’ line on the jug. Push the lid, including the middle
filler cap securely into position before commencing with operation.
To commence blending place the blender jug on the rubber Centring Pad,
ensuring that it is sitting level.
STEP
4
STEP
3

SECTION SIX | P18
Controls
SECTION SIX | P19
12
34 5 6 7 8 910
11 12 13 14 15
1. Power switch
Turns blender on or off.
2. Start / Pause
Press once to start blending cycle, press
again to pause blending cycle.
3. Setting
To setup blending cycle
4. Preset soup button
See page 19 for instructions
5. Reduce time/speed/temperature
To setup blending cycle
6. Preset smoothie button
See page 18 for instructions
7. Preset nut button
See page 19 for instructions
8. Add time/speed/temperature
To setup blending cycle
9. Pulse button
See page 21 for instructions
10. Programmable DIY button
See page 21 for instructions
11. Variable blade speed display
View blade speed 1-10
12. Time display
View cycle time
13. Jug safety display
Indicates if jug is in position
14. Blade activated display
Turns when blade is operational
15. Temperature display
Shows current temperature of
ingredients in blender.
TIP:
Use your finger tips to operate touch panel controls. Always use clean hands before operating
the touch panel control. Wipe off any water or liquid from the touch panel before operation.
Controls
Setting The Controls:
The Luvele Vibe Blender System comes with an innovative ‘one touch’ control panel. With the
simple touch of a button you can fine-tune the texture for any recipe. There are four options to
create and setup a blending cycle.
NOTE: Please be sure to read all four options for setting a blending cycle to gain a clear under-
standing of how to set & use your Luvele Vibe Blender System.
The Luvele Vibe Blender comes with 3 preprogrammed custom cycles, including smoothies,
soup and nuts. To select one of these preprogrammed cycles, simply press the ‘power switch’,
then press the preprogrammed cycle of your choice, then press the ’start’ button and the
blending cycle will commence.
Smoothie = Perfect for making smoothies of all kinds. We have preprogrammed the smoothie
button to blend for 60 seconds, to make sure smoothies are smooth, creamy and delicious
and that the nutrients have been released from their cells. We have set the temperature
to reach a maximum of 38 °C (100 °F) before the cycle stops, this is to protect the
Power Switch Start
Smoothie
1. PRE-PROGRAMMED

SECTION SIX | P20
Controls
SECTION SIX | P21
Controls
Soup = The preprogrammed soup button will run for as long as it takes for the temperature
to reach 90 °C (194 °F). Once the temperature sensor hits 90 °C (194 °F) the cycle
will stop.
The length of the soup cycle, combined with the speed of the motor, heats the ingredients
to 90 °C (194 °F). When preparing a soup recipe, remember that the speed of the blade
generates enough heat to warm the ingredients, therefore, do not add liquids or ingredients
over 45° C (115° F) to the jug when preparing soups or other hot recipes.
Nuts = The nut cycle will run for 120 seconds or will stop if the temperature reaches
100° C (212° F). When blending nuts always make sure the ingredients fully cover the blade.
The tamper is an important accessory when blending nuts. Use the tamper to move
and push nuts into the blade.
Power Switch Start
Soup Nuts
!WARNING:
When making hot soup or drinks, do not fill either jug with more
than 1L (1qt) of liquid and ingredients.
TIP:
The pulse function can come in handy when processing nuts. Use the pulse button to
get the mixture stared, then switch to the nut function to finish.
2. MANUAL SETTING
The manual setting allows you to set a one-time blending cycle manually,
controlling the blade speed, the temperature and the time. To set, press the power
button, then use the ‘reduce speed’ & ‘add speed’ arrow buttons to first set the blade
rotation speed.
Once blade speed is set, press the setting button again to set the time using the
‘reduce time’ & ‘add time’ arrow buttons once more.
When the time is set, press the setting button one more time to set the temperature.
When you are happy with all three settings, simply press the play button to begin the
blending cycle.
NOTE:
When setting the temperature, you are setting the highest temperature you
would like to achieve before the blender cycle stops. If the temperature that is set
is reached before the time is finished, then the blender cycle will stop.
NOTE:
Manual setting needs to be set every time you run a blending cycle.
The settings are not saved.
Power Switch Start
Setting Reduce time/speed/temperature
Add time/speed/temperature

SECTION SIX | P22
Controls
SECTION SEVEN | P23
Tips
The DIY memory button is a highly innovative feature on the Luvele Vibe Blender. It allows
you to program and save a blending cycle of your choice. Once you have programmed
a cycle, it will be saved until you program in a new blending cycle.
To set, use the following instructions;
Press the power switch to turn on the blender. Then press and hold down the DIY memory
button for 3 seconds until it beeps once. Use the ‘reduce speed’ & ‘add speed’ arrow
buttons to first set the blade rotation speed (1 to 10). Once blade speed is set, press the
setting button again to set the time using the ‘reduce time’ & ‘add time’ arrow buttons.
Press the setting button once more and use the ‘reduce temperature’ & ‘add temperature’
arrow buttons to set temperature. Once all three settings have been set, press and hold
the DIY memory button for three seconds, it will beep three times. This means the settings
have been saved. You can now use this blending cycle by simply pressing the start button.
3. DIY MEMORY
Power Switch Start
Setting Reduce time/speed/temperature
Add time/speed/temperature
Pulse
DIY memory
4. PULSE CONTROL:
The pulse button is used for chopping, mincing, whipping, or other blending tasks that
do not require a long blend cycle. It allows short controlled bursts of operation.
Press down and hold to operate. To stop operation, release the button.
NOTE: The DIY button will save the cycle until it is reprogrammed again. Meaning, if you
turn the blender off and turn it back on again, press the DIY button, then press the start
button it will run through the same blending cycle as saved.
The Luvele Vibe Blender has a 10-speed blade system. The blade speed
can be set to between 1 and 10. 1 being the slowest and 10 the fastest speed.
BLENDER SPEED:
Blending on high speed (10) can be used for most ingredients like fruit and vegetable
juices, soups, shakes, smoothies, frozen mixtures, purées, nut butters and for grinding
grains. Processing times will generally be less than one minute and some recipes will
take less than 30 seconds. Blending at the high speed (10) provides the best results
when breaking down ice, frozen fruits, whole fruits and vegetables, and grains to a
smooth lump-free consistency.
TIP:
Use the high speed setting as often as possible to achieve the most uniform
consistency.
If the ingredients do not circulate on the high speed, the machine may be overloaded
or may have trapped an air bubble. Carefully remove the filler cap, while making sure
the lid stays firmly in place. Release the air bubble by inserting the tamper through
the filler cap opening. If circulation problems continue, reduce the machine speed.
A lower speed may allow food to circulate when a higher speed does not. The pulse
button can also be used to help circulate ingredients that have become stuck.
TIPS FOR BLENDING ICE:
We recommend using the stainless steel jug when blending ice. To blend ice, place the ice
cubes into the blender jug. Attach the lid and filler cap and place on the centring pad.
Press and release the pulse button, repeat until the desired consistency is reached. Add a
little water and flavouring through the filler cap opening for a slushier consistency.

SECTION SEVEN | P24 SECTION EIGHT | P25
Tips
BLENDER JUG CLEANING:
TAMPER, LID AND FILLER CAP:
Separate each of these parts, and then wash them in warm soapy water. Rinse
under running water, and dry.
MOTOR BASE:
Before cleaning the base be sure to unplug the blender. Wash the outside surface with a
damp soft cloth or sponge, which has been rinsed in a mild solution of liquid detergent and
warm water. Do not place the motor base in water.
Cleaning
!WARNING:
Be careful while cleaning around
the blades, as the blades are very
sharp.
IMPORTANT:
To ensure continued and effective performance, do not put the
blender jug, lid, filler cap or tamper in the dishwasher.
!WARNING:
Never wash the blender by
putting hands into the jug.
Fill the blender jug half full with warm water and add a couple drops of
liquid dish washing detergent to the jug. Then place the lid and filler cap
into position. Turn the blender on using the pulse button for approximately
30 seconds. Turn off the blender and rinse the jug under running water. The cleaning
brush accessory provided can be used before or after the above steps to clean
thoroughly under and around the blade set. Simply insert the bottom of the cleaning
brush under the blade and rotate around the jug. Always dry jug upside down for
best cleanning results.
Minerals from fruits and leafy greens can cause a film to build up on the
blender jug overtime. To assist in removal of film, pour one cup of white
distilled vinegar into the jug, then fill half-full with warm water. Let soak for
several hours, or overnight, then pour the contents out and use the cleaning brush to
clean the inside of the container.
For a deeper clean, place four cups of water and four cups of white dis-
tilled vinegar into the jug and let it soak for about four hours. Pour contents
out and rinse thoroughly.
STEP
1
STEP
2
STEP
3
TIPS FOR BLENDING DRY INGREDIENTS:
We recommend using the stainless steel jug when grinding dry ingredients. The
preprogrammed nut button is useful when grinding dry ingredients.
Do not operate the blender for more than 120 seconds when processing dry ingredients.
Grinding dry ingredients for more than two minutes could damage your blender.
The pulse function can come in handy when processing dry ingredients. Nuts and seeds
can contain a lot of oil and will turn into nut and seed butter if blended enough. Use the
pulse button for more accurate control and consistency.
When blending dry items always be sure to add enough to cover the blades completely.
Conversely, adding too much to the blender jug can overload it.
The tamper is an important accessory when blending dry ingredients. Use the tamper
to move and push ingredients into the blade. See page 10 for more information on
using the tamper.
Regular blending of dry ingredients may result in cosmetic marring of the 2L plastic blender
jug and cause the blades to become dull over time.
Grinding some herbs may release oils, causing the plastic jug to discolour permanently.
Others have strong odours that may linger in the plastic container, affecting the flavour of
other foods. To overcome this issue we recommend using the stainless steel jug when
processing these ingredients. The grinding of some herbs and spices may also cause the
blade to dull over time.
TIPS FOR BLENDING HOT LIQUIDS:
Escaping steam, splashes or contents may scald. To secure the hot contents, place the
lid and filler cap securely in place prior to operating the blender. Always allow hot liquids
to stand for a few moments to permit steam to escape before processing.
!WARNING:
Never remove the lid or filler cap
or add ingredients while the hot
contents are being processed.
When the processing of the hot
ingredients has been completed,
removed the filler cap carefully to allow
excess steam to escape.

END RESULTS ARE UNEVEN:
Reduce the amount of ingredients in the blender jug. Ensure all ingredients are cut
approximately the same size.
INGREDIENTS ARE TOO FINE:
Use the pulse function to prevent over processing.
LIQUID IS SPILLING OUT THE BLENDER JUG:
Reduce the amount of ingredients in the jug and make sure the lid and filling cap are
securely in place.
MY JUG IS SCRATCHED OR FOGGY:
Depending on the food items being blended and the amount of use the blender
receives, the Luvele Vibe Blender jug may require replacing from time to time.
Luvele offers replacement jug and blade sets on our website www.luvele.com.
AUTOMATIC OVERLOAD PROTECTION:
The automatic overload protection feature is designed to protect the motor and
prevent the blender from overheating. If the automatic overload protection is
activated it will cause the motor to shut off and possibly emit a light odour. If your
automatic overload protection should ever be activated, then unplug blender and
rest for up to 45 minutes in a cool place.
LOCKING NUT & BEARINGS:
In the event that the stainless steel core plate or bearings at the bottom of your
blender jug loosen and no longer securely hold the blade set in place,
DO NOT CONTINUE TO USE THE BLENDER.
You can order a new jug or contact Luvele at [email protected] for assistance.
SECTION NINE | P26
Troubleshooting
The Luvele Vibe Blender System is backed by our 2 Year Total Cover Warranty.
Our warranty will covers any manufacturing fault with the product and will also cover
damage caused during transit. Your warranty starts from the purchase date of your
Luvele product.
To register your warranty please visit;
www.luvele.eu/warranty for EU registrations
www.luvele.co.uk/warranty for UK registrations
www.luvele.com/warranty for USA registrations
www.luvele.com.au/warranty for Australian registrations
If your product was ordered through a separate retailer then please keep store
invoice for warranty claims.
Warranty Process
We want to make any warranty claim as simple as possible for you. All you need to
do is contact us at [email protected] and provide us information about the
problem you are having with your item.
Firstly, we will suggest some troubleshooting ideas to establish whether or not the
issue can be fixed without a return. Photos of the fault may be requested if and where
appropriate, and if it will ensure a faster resolution.
We are here to help, so please email us and the best solution to meet your needs will
be offered. [email protected].
SECTION TEN | P27
Warranty

SECTION ELEVEN | P28
Notes
LUVELE VIBE BLENDER SYSTEM
INSTRUCTION BOOKLET & USER GUIDE
BEDIENUNGSANLEITUNG
& BENUTZERHANDBUCH
com
LUVELE VIBE
MIXERSYSTEM