LuXout Shades LSPP-12V-29A-18S User manual

INSTRUCTIONS
Dry Contact Closure Interface
Overview
SPECIFICATION SUBMITTAL
Job Name: Model Numbers:
Job Number:
I-108
1221 Admiral Street Richmond VA 23220 800-817-1204 LuXoutShades.com
LuXout Shades Dry Contact Closure
Contact closure interfaces allows integration of the Automation© systems throughout the house.
The contact closure interface communicates to LuXout Shades via ARC™ RF communication.
Each interface can control one group or one shade using two conductor - one pair #18 AWG
(1.0mm²), class 2 cable.
Many electronic systems and devices have the capability to provide status or control in the form
of dry contact closure (relay/switch) outputs. Each individual device output can be connected to a
contact closure inputs. The contact closure input is programmed from a channel on a LuXout
keypad.
Model Number LS-CCI: Wired Contact Closure Input Interface
Input Voltage 12V (from Automation System). 240z12V
Environment Ambient operating temperature: 0°C to 40°C, 32°F to 104°F. Ambient
operating humidity: 0-90% humidity, non-condensing. Indoor use only.
LuXout Shades

INSTRUCTIONS
LuXout Low Voltage Plug-In
Overview
SPECIFICATION SUBMITTAL
Job Name: Model Numbers:
Job Number:
1). When Do I Charge The Motor?
• Our motors are charged when you get them. The charge should last about 500 cycles. (Up-down)
• When the motor battery gets low on charge, it will beep at you when operating. The beeping will happen until the
motor stops. Be sure to charge the motor once it beeps at you during operation.
• Suggestion - Set a renewing calendar event on a set date each year then recharge the motor to avoid beeping.
2). Charging The Motor
• Plug in the charger into a nearby electrical outlet.
•
Connect the cable from charger to cable that is attached to the motor. The cable is 6’’ long and runs from the motor
to the plug.
• Charge 3 - 5 hours or until the LED on the charger turns green.
3). What If I Forget And Leave The Charger Hooked Up For An Extended Time?
• The batteries cannot be over-charged. LuXout motors feature a charge-management circuit that adjusts the amount
of electrical current feeding the battery. As a battery reaches its maximum charge, the circuit will limit the current
eventually shutting off power once the battery is fully charged.
Red
Light
Green
Light
Battery is
charged Battery needs
charging
1221 Admiral Street Richmond VA 23220 800-817-1204 LuXoutShades.com
LuXout Shades
I-109

INSTRUCTIONS
Power Panel
Installation Instructions
SPECIFICATION SUBMITTAL
Job Name: Model Numbers:
Job Number:
I-110
1221 Admiral Street Richmond VA 23220 800-817-1204 LuXoutShades.com
LuXout Shades
Overview
LuXout Shade 18 Output Power Panel - For use with LuXout Shades
SHOCK HAZARD
Risk of serious injury or death. Lock
circuit breaker in the off position
before servicing.
NOTICE:
This power supply is built-in fan on/off
control circuit.
Fan automatically works according to
working temperature.

INSTRUCTIONS
Power Panel
Installation Instructions
SPECIFICATION SUBMITTAL
Job Name: Model Numbers:
Job Number:
I-111
1221 Admiral Street Richmond VA 23220 800-817-1204 LuXoutShades.com
LSPP-12V-29A-18S
For use with LuXout Shades
100 - 120VAC/6.8A
200 - 240VAC/3.4A 12VDC 29A
Installation Instructions (Save these instructions)
Read and Follow all instructions
Tools Required:
• Wire Cutter/Stripper
• #2 Flat Head Screwdriver
• Power Drill
• #2 Phillips Screwdriver
NOTE: Mounting hardware is not included due to the wide variety of wall materials. Customer
should determine the appropriate mounting hardware for ther specific needs.
Box Contents: LSPP-12V-29A-18S
The Output Power Supply Panel is a surface mount plug in power supply for use with 12 volt
powered shades. LSPP-12V-29A-18S simplifies the wiring and organizes installations that require
multiple power supplies.
1). Important Notes
1. All wiring must be in accordance with national and local codes
2. Note: Secondary wiring must be of type CL2, CL2P, CL2R, CL2X or other cable with
equivalent or better electrical, mechanical, and flammability ratings in accordance with all
local and national electric codes.
3. LSPP-12V-29A-18S does not need to be installed by a qualified electrician.
4. Ambient operating temperature: 32 to 104F (0 to 40C), 0-90% humidity, non-condensing.
5. This product is intended for indoor use only.
6. This panel may not be compatible with any other shade devices.

INSTRUCTIONS
Power Panel
Installation Instructions
SPECIFICATION SUBMITTAL
Job Name: Model Numbers:
Job Number:
I-112
1221 Admiral Street Richmond VA 23220 800-817-1204 LuXoutShades.com
LSPP-12V-29A-18S
2). Installation
A. Open metal outer panel cover.
B. Choose panel mounting location so line voltage wiring is at least 6 ft (1.8 m) from audio or
electronic equipment and associated wiring (prevents radio frequency interference).
C. Use fasteners rated for a 25 lb (11.3 kg) load.
Notes:
• Mount the Power Panel in a position where it can be easily located and accessed if service or
troubleshooting is necessary.
• Mount the LSPP-12V-29A-18S in the orientation shown (Mounting Hardware is not provided). Do
not mount in any other orientation.
• For indoor use only.
• NEMA, Type 1 enclosure, IP30.
• Install in accordance with all
national and local electrical codes. +3/4”
Bottom View
Knockout Pattern
(from outside of box)
+ + 3/4”
3/4”
Top View
Knockout Pattern
(from outside of box)
C+3/4”
Left Side View
Knockout Pattern
(from outside of box)
A = 11’’
B = 9’’
C = 3 1/2’’

INSTRUCTIONS
Power Panel
Installation Instructions
SPECIFICATION SUBMITTAL
Job Name: Model Numbers:
Job Number:
I-113
1221 Admiral Street Richmond VA 23220 800-817-1204 LuXoutShades.com
LSPP-12V-29A-18S
3). Line Voltage Wiring
A. SHOCK HAZARD. Risk of serious injury or death. Locate and lock the supply
breaker in the OFF position before wiring to the screw blocks.
Note: Maximum of 2 LSPP-12V-29A-18S power supplies per 20 A breaker, or 1 per 15 A breaker.
1. Turn power off at circuit breaker.
2. Plug provided power cord into wall socket.
NOTICE:
This power supply is built-in fan on/off
control circuit.
Fan automatically works according to
working temperature.

INSTRUCTIONS
Power Panel
Installation Instructions
SPECIFICATION SUBMITTAL
Job Name: Model Numbers:
Job Number:
I-114
1221 Admiral Street Richmond VA 23220 800-817-1204 LuXoutShades.com
LSPP-12V-29A-18S
4). Low Voltage Wiring
A. SHOCK HAZARD. Risk of serious injury or death. Locate and lock the supply
breaker in the OFF position before wiring to the terminal blocks.
Note: Note: All secondary wiring must be of type CL2, CL2P, CL2R, CL2X or other cable with
equivalent or better electrical, mechanical, and flammability ratings in accordance with local and
national electric code.
1. Unplug panel.
2. Remove as many knockout tabs as necessary from the top of the enclosure and insert
0.50 in strain reliefs (not included) into the open knockout holes.
3. Route the wire through the strain reliefs and to the output terminal blocks.
4. Strip the wire insulation so that 0.25 in of bare wire is exposed. Insert the Common leads
into the (-) Terminal screw and the +12 V leads into the (+) Terminal screw. Tighten the
terminal blocks to 3.5 - 5 in•lb (0,4, -0,6 N•m). Make sure the wire insulation is not
pinched.
5. Close metal cover securely back onto the enclosure and tighten the screws.
6. Restore power to the panel by plugging into outlet.
7. IMPORTANT NOTE: No more than 5, 35mm or 45mm motors can be wired to each of the
sections. Do not overload section. For 25mm & 28mm motors the maximum number is 9
per section.
B. Wire Length Chart
Use this chart to determine the maximum wire length, from panel to shade, based on the gauge
of the wire that is used.
Distance to
shade
16 AWG
(1.5 mm²)
18 AWG
(1 mm²)
125 ft (35 m)
200 ft (60 m)

INSTRUCTIONS
Power Panel
Installation Instructions
SPECIFICATION SUBMITTAL
Job Name: Model Numbers:
Job Number:
I-115
1221 Admiral Street Richmond VA 23220 800-817-1204 LuXoutShades.com
LSPP-12V-29A-18S
5). Low Voltage Wiring
A. SHOCK HAZARD. Risk of serious injury or death. Locate and lock the supply
breaker in the OFF position before wiring to the terminal blocks.
1. Turn off power at the circuit breaker.
2. Route the secondary wiring to the shade so the connection to the shade wiring can be
concealed in the shade headbox. Secondary wiring may be routed into the headbox either
by dropping the wire in through the top of the headbox, or drilling a hole in the shade
endcap.
3. Identify the shade wiring cable.
4. Remove 0.25 in (6.3 mm) of the insulation from both the white and white/black wires.
5. Connect the wires to the shade cable using the provided WAGO wire connectors.
Connect the white shade wire to the +12V lead of the wiring. Connect the white/black
shade wire to the common of the wiring.
6. Restore power to the Power Panel and confirm that the shade is energized. Refer to the
LuXout Shade Installation and Programming guide for programming and operating
instructions.
Connect the
secondary wiring
to the shade
wiring cable via
wire connectors
provided.
- Connection should
be concealed
within headbox