LUZ NEGRA 41.018 User manual

www.luznegra.net
3V
voltage IP20
SEQUENCERS FOR LEDS
CCT DIMMER CONTROLLER FOR 6 ZONES
Ref: 41.018 Controller
Features
• Compact size with simple and easy-to-use interface.
• Accurate and smooth colour temperature and brightness adjustment for
warm white and cold white.
• 256 level brightness adjustments for each white to archive millions of colour
temperatures.
• Smooth dimming without any flickering from 0.1% to 100% enables the
dimmer controller to archive millions colours.
• Control 6 different zones separately or synchronously with endless receivers
in each zone.
• Save kelvins / scenes for each zone.
• Control distance around 20-30m.
• To work with power repeater to expand output unlimitedly.
Compatible with controller:
• 41.019
Voltage (V) 3V (1 units of CR2025
not included)
Frequency 868/915/434MHz
Control 6 zones
Signal distance 20 - 30m
Waterproofing IP20
Working temperature 0°C / 40°C
Measurements 136.3x38.9x10.7mm
Packaging 1 unit
Guarantee 2 years
136.3
38.9 10.7
Approved by:
BARCELONA
C/ Carles Buhigues, 13
08420 Canovelles
[e-mail]
Tel: [phone]
MADRID
C/ Adaptación, 27
28906 Getafe
[e-mail]
Tel: [phone]
PARIS
113 Avenue Jore
77450 Esbly
[e-mail]
Tel: [phone]

www.luznegra.net
Remote button diagram:
Back
Front
SEQUENCERS FOR LEDS
CCT DIMMER CONTROLLER FOR 6 ZONES
BARCELONA
C/ Carles Buhigues, 13
08420 Canovelles
[e-mail]
Tel: [phone]
MADRID
C/ Adaptación, 27
28906 Getafe
[e-mail]
Tel: [phone]
PARIS
113 Avenue Jore
77450 Esbly
[e-mail]
Tel: [phone]
Control the receiver’s cw channel,
ress and hold down to increase /
decrease light intensity.
Press and hold down to increase light
intensity smoothly.
Control the receiver’s ww channel, press
and hold down to increase / decrease
light intensity.
Press and hold down to decrease light
intensity smoothly.
6 zones, click to choose a zone,
press and hold down to turn ON/OFF
corresponding zone
On/Off
Safety & warnings
• This device contains a button lithium battery that should be stored and disposed of properly.
• DO NOT expose the device to moisture.
Note: before the first use, please remove the protective film on the battery.

www.luznegra.net
Pair with RF receiver
SEQUENCERS FOR LEDS
CCT DIMMER CONTROLLER FOR 6 ZONES
BARCELONA
C/ Carles Buhigues, 13
08420 Canovelles
[e-mail]
Tel: [phone]
MADRID
C/ Adaptación, 27
28906 Getafe
[e-mail]
Tel: [phone]
PARIS
113 Avenue Jore
77450 Esbly
[e-mail]
Tel: [phone]
Step 1: do wiring of the RF receiver according to wiring diagram(please refer to the instruction of RF receiver that you would like
to pair with.
Step 3: choose and click a zone number (e.g. zone 4).
Step 4: click any of the four buttons , led lights connected with the RF receiver flicker once means the receiver is
paired with zone 4 successfully.
After pairing, choose and click one or multiple zone numbers, then press and hold any of the four buttons to operate.
Note: one receiver can be paired with max 8 remote controls.
Step 2: click the “Learning Key” button on RF receiver to set it into pairing status
If you use multiple receivers, you have two options:
Option 1: have all the receivers in the same zone, like zone 1.
Option 2: have each receiver in a different zone, like zone 1, 2, 3 or 4.
Zone 1
Zone 1 Zone 2 Zone 3
Remote control
Remote control
RF led receiver
Learning Key
RF led receiver
Learning Key
RF led receiver
Learning Key
RF led receiver
Learning Key
RF led receiver
Learning Key
RF led receiver
Learning Key