LY International HS6813 User manual

LY International Electronics Co., Ltd
Home Music System HS6813
Welcome use our Home Music System. For better use of the system, please read the manual carefully
before use.
User’s Manual
Infrared Remote Controller HS21
Home Music System HS6813
Remote Control Pad HS30R
Speaker Unit
Speaker Unit

Contents
※Overview...................................................................................................................................................1
1. Introduction to Home Music System..................................................................................................1
2. System Features..................................................................................................................................1
※Descriptions of Console............................................................................................................................2
1. Descriptions of Front Panel................................................................................................................2
2. Description of Rear Panel................................................................................................................... 3
※System Wiring Diagram............................................................................................................................5
1. Console Wiring Example....................................................................................................................5
2. Typical Zone Wiring Example............................................................................................................ 5
※Operation Instructions for Console ........................................................................................................... 6
1. Description of Start-up State ..............................................................................................................6
2. Operation Instruction for Manual Zone Control................................................................................. 6
3. Manual Operation Instructions for MP3 Player..................................................................................6
3.1 Mode Selection................................................................................................................6
3.2 Time Display...................................................................................................................7
3.3 Song Selection.................................................................................................................7
4. Manual Operation Instructions for Tuner...........................................................................................7
4.1 Band Selection.................................................................................................................7
4.2 Radio Station Search.......................................................................................................7
4.3 Storing a Radio Station.................................................................................................... 8
4.4 Mute Mode......................................................................................................................8
4.5 Calling a Radio Station Channel .....................................................................................8
5. Timer Programming ...........................................................................................................................8
5.1 Timer Setting...................................................................................................................8
5.2 Time Adjustment ........................................................................................................... 10
5.3 Copying a Timing Point ................................................................................................ 11
5.4 System Setting............................................................................................................... 11
※Function Description for Infrared Remote Controller............................................................................. 11
※Wiring Method for Remote Control Pad.................................................................................................13
※Description for File Format Applications of USB Flash Disk................................................................. 13
※Precautions............................................................................................................................................15
1 Safety Operation...............................................................................................................................15
2 After-sales Service............................................................................................................................15
※Packing List.............................................................................................................................................16
※Specifications.......................................................................................................................................... 16
1. MP3 Player.......................................................................................................................................16
2. AM/FM Tuner ..................................................................................................................................16
3. Timer ................................................................................................................................................17
4. Comprehensive Specifications .........................................................................................................17

* LY * Home Music System
1
※
※※
※Overview
1. Introduction to Home Music System
HS6813 Home Music System is a set of ideal modern Home Music System combining not only all
functions of traditional home hi-fi, but also: 1. Timing point. i.e. Enables the presetting of a
special timing point and specific task executed at the timing point. For example, the alarm clock
can be set to wake you up on time; the bell can be set to remind your kids of going to school; Fresh
and melodious background music can be heard the moment you enter your house after your busy work;
when you listen to background music in your room and the news starts on TV, you can enjoy the news
on time without walking out of your room. You can preset all these items on the system within only
several minutes, and the system can execute what you set automatically. 2. Different music programs
for different rooms simultaneously. For example, while the aged and the young have different music
tastes, the aged can enjoy traditional opera program in their room while the young can enjoy pop
music in their room, and TV program can be watched in sitting room while the TV program can be
listened to in kitchen or bathroom. All that can be executed synchronously.
In addition, the system features an important function which allows the console to be controlled in a
room. For example, by operating the remote control pad in the room, you can select the program
content played by console and adjust the volume and tone level of the room.
The console of this set of system is integrated with MP3 player, tuner, zone selector, timer, pre- and
rear amplifiers, and equipped with input interfaces for four peripheral sound source equipment (DVD,
PC, TV, and AUX), MP3 OUT and TUNER OUT auxiliary output interfaces, 6 stereo output channels
for connecting to 6 zones, 6 remote control data interfaces for connecting to the remote control pads of
6 zones. So, interactive bi-direction control is formed across the console and remote control pads to
offer you great ease of use.
2. Console Features
●
●●
●Features modern multi-function Home Music System.
●
●●
●Built-in MP3 player and tuner.
●
●●
●With USB interface equipped, the console supports music files in MP3 format from flash
disk, MP3 player, portable hard disk, card reader, etc..
●
●●
●FM andAM bands for tuner.
●
●●
●External DVD audio input interface, PC audio input interface, TV audio input interface,
auxiliary audio input interface, MP3 audio output interface, and tuner audio output
interface which are all connected through RCA plugs.
●
●●
●With 6 independent stereo output channels connecting to 6 zones, the volume and tone of
the zones can be adjusted respectively.
●
●●
●Different sound sources can be distributed in 6 zones simultaneously.
●
●●
●Console control and remote control available.
●
●●
●Timing control is available for the 2 built-in sound sources and 4 external sound sources, up
to 100 timing points can be edited and the timing points are repeated weekly.
●
●●
●The start time of the timing point can be set to second.
●
●●
●1 channel of 220V timing control output power for peripheral sound source available.

* LY * Home Music System
2
※
※※
※Descriptions of Console
1. Descriptions of Front Panel
1: Power indicator
On when the power is on, off when the power is off. The indicator is yellow when the console is under
standby state; otherwise, it is green.
2: Power button
The power is on when the button is pressed down, and the power is off on the contrary.
3 and 6: key switches for 6 zones.
4: Timer setting switch
Access to the timer setting interface by pressing the key slightly.
5: Zone setting switch
Access to zone management interface by pressing the key slightly.
7: AM/FM key for tuner
8: Operation key for radio station storage of tuner
9: Mono/Stereo key for tuner; Stop key for MP3 program.
10: Mute key for tuner; Pause/Play key for MP3 program.
11: Operation key for tuning to the next stored tuner radio station; operation key for playing the next
desired MP3 program.
12: Operation key for tuning to the previous stored tuner radio station; operation key for playing the
previous desired MP3 program.
13: USB interface
You can insert USB flash disk, portable hard disk or card reader into here.
14: MP3 setting switch
Access to the MP3 setting interface by pressing the key slightly.
15: Tuner setting switch
Access to the tuner setting interface by pressing the key slightly.
16: LCD display screen
Displays all operation states and setting operation interfaces of the console.
17: Jog dial
The jog dial can be used to search a radio station frequency while tuner mode; can be used to search a
program, select and confirm the circulation mode while MP3 mode; can be used to point to, and select
the desired item and confirm the present operation result while timer setting mode; and can be used to
point to the item, access to the zone control interface, operate each item and confirm the present
operation result while zone control mode.
Key Function Forced switching:

* LY * Home Music System
3
Forced switching can be carried out by function keys on the console while in primary menu (interface).
For example, to switch to MP3 mode, you can press “MP3” key while in TUNER state; in case of
pressing “TIMER” key, you can access to timer setting interface; by pressing “ZONE” key or one of
the 6 zone keys, you can access to the zone state display interface (equipment system main interface).
The interfaces which can be switched to are as shown in the figure below:
2. Description of Rear Panel
1) DVD audio input interface
Audio output interface for connecting to a DVD player.
2) PC audio input interface
Audio output interface for connecting to a PC.
3) TV audio input interface
Audio output interface for connecting to a TV.
4) Auxiliary audio input interface
Interface for connecting to a random sound source equipment, such as player, tuner, etc..
5) MP3 audio signal output interface
Interface for connecting to an amplifier or an audio monitor.
6) Tuner audio signal output interface
Interface for connecting to an amplifier or an audio monitor.
7) Audio output interface for zone Lchannel
Interface for connecting to a zone enclosure. Pay attention to the polarity while connecting.
8) Audio output interface for zone R channel
Interface for connecting to a zone enclosure. Pay attention to the polarity while connecting.
Operation Selection
Timer Setting Adjust Time
Copy Timing System Setting Exit
DVD
TUNER
PC
TV MP3
PC
Mode
MP3 Player
03
\
01
Overriding directory,
please wait…
Play All
00
：
00
00
：
00
BAND FM
100.45
100.45100.45
100.45 MHz
Signal
MONO
AM/FM tuner
MEMO 40

* LY * Home Music System
4
9) Power input interfaceAC220V
Please connect the power cord to the console securely before connecting it to the power grid.
10) FM antenna interface
Input impedance is 75Ω. Interface for connecting to the provided FM antenna or the wired TV
network.
11) AM antenna interface
For connecting to the provided AM antenna.
12) Data exchange interface
Data exchange between 6 zone remote control pads and console, one interface corresponds to one
zone.
13) Power output socket for timer.

* LY * Home Music System
5
1.Console Wiring Example
2. Typical Zone Wiring Example
Amplifier
Tape player
TV
DVD player
FM antenna
AM antenna
1
st
zone 6
th
zone
Zone 1 to Zone 6
L channel
R channel
L channel
R channel

* LY * Home Music System
6
※
※※
※Operation Instructions for Console
1. Description of Start-up State
Connect wires securely according to the system wiring diagram, connect to the power and press down
the power button to switch on the console. If no zone is on, the system gets into standby state
automatically, and the display screen displays the standby interface (as shown in Fig. 1-1), and the
power indicator is yellow. A zone can be opened by pressing one zone key (such as ZONE2 key) on
the panel in standby state, and the system accesses to the main interface (as shown in Fig. 1-2), namely
displays the On/Off state, sound source, and volume state of the present zone while the power
indicator is green.
-
2. Operation Instruction for Manual Zone Control
Operations to a zone include selecting the sound source for each zone, and adjusting the volume and
tone of the zone. Procedures are as follows:
Access to the zone operation interface Turn the jog dial to select one zone while main interface (as
shown in Fig. 2-1), and then press down the jog dial once to access to the zone control operation
interface (as shown in Fig. 2-2). Set the items of the opened zone in this interface.
Selecting a sound source Turn the jog dial to move the cursor (Note: the cursor refers to the
dark-grey icon displayed by the item.) to the box following the “Program”, and then press the jog dial
once when a icon appears. Turn the jog dial again, and 6 kings of program sound sources are
displayed in turn. When displaying the desired sound source, press the jog dial again and the selected
sound source is assigned to the zone.
Volume adjustment Turn the jog dial to move the cursor to the adjusting slider behind the “VOL”
and press the jog dial once. When a icon appears, turn the jog dial clockwise or counterclockwise to
move the slider to the left or right while the zone volume is increased or reduced. The treble and bass
volume can be adjusted by the same way.
After the operations above, turn the jog dial to move the cursor to the “Yes” box, press the jog dial
once to confirm and exit.
The other zones can be controlled according to the method above.
3. Manual Operation Instructions for MP3 Player
Press “MP3” key on the panel to access to MP3 player setting interface (as shown in Fig. 3-1).
3.1 Mode Selection
This operation can be used for selecting the MP3 playing mode including “All Play”, “Single Play”
and “Single Repeat”. “Play All” mode is to play all music file stored in the memory in order; “Single
2006.10.01
SUN 8：35：16
Next timing point: MON. 8: 00: 00
Off
Off
Off Off Off
DVD
(Fig. 1-1)
(Fig. 1-2)
Off Off
Off Off Off
DVD
(Fig. 2-1)
Zone 01 control
DVD
Pro.
VOL
Bass
Trebl
Yes
(Fig. 2-2)

* LY * Home Music System
7
Play” mode is to play the presently selected song only; “Single Repeat” mode is to play the presently
selected song repeatedly.
The setting method is: turn the jog dial to move the cursor to the box behind the “Mode”, press the jog
dial. When a icon appears, turn the jog dial to select, confirm and exit after selection.
3.2 Time Display
As shown in Fig. 4-1, the first “00:00” represents the time progress of the presently played song, the
following “00:00” represents the total time of the presently played song.
3.3 Song Selection
As shown in Fig. 3-1, move the cursor to “ / ” box, press the jog dial and turn it to select. The
digits of the first box represents the directory, (for example, if “03” is selected, the 3
rd
directory in the
USB flash disk is selected), and the digits of the following box represents the song No. in the directory,
and the name of the song is displayed behind the box. While selecting a song, please pay attention to
the indication at the bottom of the screen, where “No USB flash disk, please insert a USB flash disk.”
represents that no USB flash disk is inserted into the USB interface or the inserted USB flash disk
can’t be identified, and where “USB flash disk has been inserted, please wait…” represents that a USB
flash disk has been inserted and can be accessed to; When there is no song in the USB flash disk, “No
song in the directory, please select another directory.” is indicated when the directory is selected, and
then it will to another directory and display the name of song in the directory automatically.
Exit the MP3 setting interface by pressing other function key after setting.
You can select a song by “ ” and “ ” keys on panel while manual MP3 control, use “ ”
key to play or pause, and use remote control pad and infrared remote controller to operate. For details,
please refer to the User’s Manual and key function description.
4. Manual Operation Instructions for Tuner
Press “TUNER” key on the panel to access tot eh tuner setting interface (as shown in Fig. 4-1), where
the wave band, radio station channel, sound channel, etc. of the tuner can be set.
4.1 Band Selection
Selection between AM and FM can be switched by pressing the “BAND” below the display screen on
the panel. And can be switched by pressing AM/FM key on remote control pad and infrared remote
controller. The frequency scope of AM band is 522KHz-1620KHz; and the one of FM band is
87.00MHz-108.00MHz.
4.2 Radio Station Search
Press the “ ” and “ ” keys below the display screen on the panel to search the next or the
previous radio station No. as to call the stored radio station. You can also use the jog dial to search
radio station. Turn the jog dial clockwise and the frequency is increased, namely, the system searches
towards the high frequency band continuously. In case a radio station is found, a black indication bar
as shown in Fig. 4-1 is displayed behind the “Signal”. The indication bar will be widened when the
signal gets stronger; and be narrowed when the signal gets weaker. Turn the jog dial for a circle
quickly, the system will access to automatic search state. In case a radio station channel or the highest
Mode
MP3 player
03
\
01
One thousand and one nights
(Fig. 3-1)
Play All
00
：
00
00
：
00
(Fig. 4-1)
BAND FM
100.45
100.45100.45
100.45 MHz
Signal
MONO
AM/FM tuner
MEMO 40
03
01

* LY * Home Music System
8
frequency band is reached, the system will stop; Turn the jog dial clockwise, the system searches
towards the low frequency band, and the signal display and automatic search operation are the same.
4.3 Storing a Radio Station
You can press “MEMO” key together with the “ ” or “ ” key to store up to 40 radio station
successively or at random regardless of manual or automatic radio station search. While storing a radio
station, the memory No. behind the “MEMO” on the screen will flash by pressing “MEMO” key once.
Press “ ” or “ ” key to select the memory No. and press “MEMO” key again to store the found
radio station channel to the present memory No..
4.4 Mute Mode
Press the “ ” key on the panel, the “ ” icon turns into “ ” icon (as shown in Fig. 4-2) which
indicates that the tuner is in mute mode. When the timing point is reached, the system executes the
preset content of the timing point. Press the “ ” key again to cancel mute mode.
4.5 Calling a Radio Station Channel
A stored radio station channel can be called at timing point. The operation method can be referred to
the description of timing point setting.
A stored radio station channel can be called directly by remote control pad and infrared remote
controller. The operation method can be referred to the description of keys of each remote controller.
5. Timer Programming
Pressing the “TIMER” key on the panel, the system will access to the timer programming state, and
the screen will display the main interface for timer programming (as shown in Fig. 5-1), of which
timer setting, time adjusting, copying timing, and system setting can be programmed.
5.1 Timer Setting
Turn the jog dial to move the cursor to the “Timer Setting”, press the jog dial once to access to the
timer setting interface (as shown in Fig. 5-1-1), and turn the jog dial set each item in timer setting.
5.1.1 Weekday Setting:
Turn the jog dial to move the cursor to “Weekday” and press down the jog dial. When a icon
appears, turn the jog dial to call the desired weekday (such as Wednesday) and press the jog dial to
confirm and exit.
5.1.2 Adding a New Timing Point:
Adjust the date of “Weekday” to a weekday (such as Monday), all information of the 1
st
timing point
will be displayed at the other items of the interface. If there is no display at the other items (as shown
in Fig. 5-1-2), the day has no timing point. For programming a timing point, click “Add” first and set
each item. In case a timing point exists and an additional timing point is necessary, please click “Add”
first, and then program the other information of the timing point. The number of the newly added
timing point is always behind all the previously set timing points of the same day. However, the timing
point will be executed according to the time priorities of the timing points automatically.
5.1.3 Number Item Setting:
Turn the jog dial to move the cursor to the digit box behind the “Number”, and press the jog dial once.
When a icon appears behind the box, turn the jog dial again to call the desired digit, and press the
(Fig. 4-2)
BAND FM
100.45
100.45100.45
100.45 MHz
Signal
MONO
AM/FM tuner
MEMO 40
Mute
mode
of the
tuner