Lyngdorf Audio MP-60 User manual

[Skriv tekst]
PRELIMINARY MANUAL
Lyngdorf MP-60
Version: 0.2/fsm
Based on SW 3.5.3

Lyngdorf Audio MP-60 –Owner’s manual 2
Table of Contents
Compliance.........................................................................................................4
Introduction.........................................................................................................5
Pre-Installation....................................................................................................6
Unpacking the Product....................................................................................6
Home Automation System Integration ................................................................7
Preparing for Mounting in a Rack .......................................................................7
Rear Panel..........................................................................................................8
Remote Control...................................................................................................9
How to Pair Remote Control in RF Mode......................................................10
Switching Remote Between RF and IR Mode...............................................10
Getting Started (details in following chapters)...................................................10
Installation Via Installer Menu .......................................................................11
Installation Via Web Interface........................................................................11
Home Screen....................................................................................................11
Setup ................................................................................................................13
Source Setup ................................................................................................13
Speakers and Room......................................................................................15
Verify Speakers.............................................................................................20
Adjust Sub.....................................................................................................20
Channel Gain................................................................................................20
RoomPerfect™ .................................................................................................21
How to Set Up RoomPerfect™ .........................................................................21
RoomPerfect™ Preparations ........................................................................22
Measuring the Focus Position.......................................................................23
Measuring Random Room Positions.............................................................23
System Configuration........................................................................................26
General Setup...............................................................................................26
Trigger Setup ................................................................................................27
Network Setup..................................................................................................28
Streaming Setup...............................................................................................30

Lyngdorf Audio MP-60 –Owner’s manual 3
Streaming Playback ......................................................................................30
Video Setup......................................................................................................33
Video Output.................................................................................................33
Video Input....................................................................................................34
Zone B Setup....................................................................................................35
Audio Setup......................................................................................................35
Audio Processing ..........................................................................................35
Voicing Setup................................................................................................35
Manage Software..............................................................................................36
Download system log....................................................................................36
Backup..........................................................................................................36
Restore..........................................................................................................36
Factory Reset................................................................................................36
Update Software ...........................................................................................37
Troubleshooting................................................................................................38
RoomPerfect™..............................................................................................38
Error Messages.............................................................................................38
Trademarks.......................................................................................................41
Service Information...........................................................................................41

Lyngdorf Audio MP-60 –Owner’s manual 4
Compliance
WEEE
The European Parliament and the Council of the European Union have issued the Waste Electrical and
Electronic Equipment Directive. The purpose of the Directive is to prevent waste of electrical and electronic
equipment and to promote reuse, recycling, and other forms of waste recovery. Lyngdorf products and the
accessories packed with them are subject to the WEEE Directive. Please dispose of any waste materials in
accordance with your local recycling regulations. Products and equipment which must be collected for reuse,
recycling, and other forms of recovery are marked with the icon of the crossed-out waste receptacle.
FCC
Lyngdorf products and accessories comply with parts 15 and 68 of the FCC rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference; and (2) this device must accept
any interference received, including any interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment. Equipment marketed to a consumer must be capable of complying
with the necessary regulations in the configuration in which the equipment is marketed.

Lyngdorf Audio MP-60 –Owner’s manual 5
Introduction
The MP-60 is an advanced Surround Sound, Preamplifier / Processor with full support of the latest Dolby®
Atmos, DTS:X PRO (available spring 202) and Auro-3D® surround sound formats. The processor can
decode 16 discrete channels from the source and features 16 balanced XLR outputs for the discrete
channels or additional subwoofer outputs. Whatever your setup is, the MP-60 will provide the optimal
performance due to its bass-management and room correction system, RoomPerfect™.
Both Dolby, DTS and Auro provides modes for processing legacy surround formats or for upmixing the
sound into all your speakers. This is referred to as POST PROCESSING, and it can be set on a Source or
controlled from your remote control.
The MP-60 will support any setup from the simplest STEREO setup to the most advanced 3D surround
setup, and we have made great efforts for having a simple user interface, where all settings are displayed
and arranged for easy installation.
Optional modules will allow for digital integration with the most advanced media sources and/or digital
distribution of the output signals (Ref.: AES3 or AES67 formats).
Please read through this manual for understanding the functions available –or as later reference.
- The latest version of this manual is available for download from www.lyngdorf.com
Enjoy !

Lyngdorf Audio MP-60 –Owner’s manual 6
Pre-Installation
Please read all material carefully prior to installation. If you need additional assistance, contact your Lyngdorf
Audio representative or visit Lyngdorf.com.
Unpacking the Product
Carefully remove the unit and accessory kit from the carton and check for shipping damage. Contact the
shipper and your Lyngdorf Audio representative immediately if the unit bears any sign of damage.
Note: Keep the shipping carton and all packing material for future use. If this unit is
shipped for service without the original packing, damage could occur and void the
warranty.
Inventory
Check the list below to ensure that all necessary product components have been delivered. Report all
discrepancies to your Lyngdorf Audio representative immediately.
•Owner’s manual
•Power cord
•Remote
•Microphone
•Microphone stand
•Microphone cable
•Rack ears
Operating Voltage
Lyngdorf Audio products must be connected to the mains power system only. The MP-60 will automatically
detect voltages between 100-240V.
Ventilation Requirements
The MP-60 does not have a built-in fan, nor does it require special measures to ensure proper heat
dissipation. It should be placed according to these guidelines:
•It should always have at least one inch / 25mm of free space on all sides.
•It should be placed in an environment free of excessive heat.
•In a rack system, the MP-60 should be placed at the bottom of the rack, still with at least one inch /
25mm free space on top and sides.

Lyngdorf Audio MP-60 –Owner’s manual 7
Home Automation System Integration
The MP-60 is compatible with home automation systems via the RS232 and network connector on the rear
socket panel. The MP-60’s IR and trigger connections can also be programmed for use in a home
automation system.
IP Control
Connect the MP-60 to your local network and access the MP-60 by going to http://mp60.local in your
browser.
Pressing the OK button on the remote and toggling through the information, you will see the IP address
allocated to the MP-60.
Open a TCP connection on port 84 and use the same protocol as on the serial interface. Use Telnet, Putty,
or a similar program to open the TCP connection.
If you do not know the IP address of the MP-60 on your local network, the MP-60 supports Apple´s Bonjour
Discovery service, which must be on the computer with which you wish to set up the MP-60. The software is
built-in as part of the Apple OS X operating system (not iOS devices). For Windows operating systems, the
software can be found at http://www.apple.com/support/bonjour/
Preparing for Mounting in a Rack
The MP-60 processor is equipped from the factory with feet for free-standing placement.
To install the MP-60 in a rack:
1. Turn the MP-60 upside-down and place it on a stable, even surface.
2. The screws used to fasten the rack brackets to the bottom of the MP-60 are in the holes designated
for the brackets when the product leaves the factory.
3. Fasten the brackets for rack mounting to the MP-60.
4. If so required, the feet can be removed
5. Mount the MP-60 in a rack.
Note: A rack mount kit is available for achieving a cleaner 4U
rack-size (item # 900008201)

Lyngdorf Audio MP-60 –Owner’s manual 8
Rear Panel
On the back of the MP-60, you will find a range of inputs and outputs:
•16 x XLR, Differential balanced audio outputs (configured for 7.1.4 plus 4 auxiliary)
•8 x HDMI inputs and 2 x HDMI outputs, all 4K / 18 Gbps compatible. eARC on HDMI OUT 1
•1 x HDBaseT™ output
•2 x USB A connectors, for music file playback, backup, software updating, etc.
•1 x Streaming USB B audio input
•1 x RJ45 Network connector (LAN/Ethernet)
•1 x Microphone input for the RoomPerfect™ room correction microphone
•1 x SD card slot for storing backup data
•3 x Inputs from external IR receivers (IR remote control)
•1 x Trigger input and 4 x trigger outputs
•1 x RS-232 connector for serial control of the unit
•1 x DB-25 16 channel DCI-compliant AES3 digital input (optional upgrade)
•1 x DB-25 16 channel DCI-compliant AES3 digital output (optional upgrade)
•1 x RJ45 16 channel AES67-complient digital input/output (optional upgrade)
•4 x Optical, 1 x AES/EBU and 3 coaxial digital audio inputs
•1 x Coaxial digital audio output –stereo for Zone B (ref.: Zone 3)
Notes: HDBaseT™ is a standard for having up to 100 meter / 300 feet cable to your
television or projector. Using optical HDMI cables will require using an USB connection
for power supply, as the HDMI connector provides max. 5V/50mA.
Differential balanced output connection means that PIN 1 is Shield/Ground, PIN2 holds
audio signal and PIN 3 holds an inverted audio signal. If your power amplifier requires a
single ended (RCA) connection, you must ensure that the PIN 3 is disconnected (lifted).
PIN 3 in the MP-60 connector may not be connected to ground.

Lyngdorf Audio MP-60 –Owner’s manual 9
Remote Control
The MP-60 comes with a dedicated remote control, which can operate both with radio frequencies (RF) and
infrared control (IR)
Setup Access the installation menu.
Standby Turn the MP-60 on and into standby.
Audio Access the post-processing menu.
Trim Access to miscellaneous audio adjustments.
Up/Down Move up and down in menus.
Browse available settings in a menu.
Toggles between the available RoomPerfect™ filters.
Left/Right Move left and right in menus.
Toggle between neutral and the available voicings.
OK Activate the info screen, indicating the status of
the unit.
Select a menu and store a selected setting.
Back Return to the previous menu.
Menu Access the user menu.
SRC Access the source menu list.
Source -/+ Toggle between active sources.
Volume +/- Turn volume up and down.
Mute Mute and restore the sound.
Play/Pause Play/pause the currently playing track in the media player.
Skip Forward/ Skip in the current playlist in the media player.
Backwards

Lyngdorf Audio MP-60 –Owner’s manual 10
How to Pair Remote Control in RF Mode
The MP-60 remote has both an IR and RF mode, and is by default set to IR.
To pair the RF remote control to the MP-60:
1. Turn on the MP-60.
2. Hold down Play/Pause and OK until the remote control´s green LED flashes.
3. Release the buttons.
4. Point the remote control at the MP-60 and hold it within 30cm / 1 foot of the front panel; when the
green LED stops blinking, the remote is connected.
5. The remote is now RF paired to the MP-60.
To reset the pairing of the remote control, press Back and OK until the red LED flashes twice.
Switching Remote Between RF and IR Mode
To switch the remote from IR to RF mode, hold down OK and 2. The LED will flash green twice.
To switch the remote from RF to IR mode, hold down OK and 1. The LED will flash red twice.
If you press a button on the remote and the red LED at the top turns on, then you are in
IR mode. If it turns green you are in RF mode.
Getting Started (details in following chapters)
Setting up the MP-60 surround sound processor requires either a network connection or a HDMI connection
to a screen by following these steps:
1. Connect the speakers to the power amplifiers.
2. Connect all external equipment, audio & video, home automation system, mains power, etc. to the
MP-60.
3. Switch on the MP-60 mains connector on the back and all connected equipment.
4. Turn on the MP-60
5. Access the setup menu via the web interface or press Setup on the remote for having the Menu on
the connected screen.
6. Go to “Speaker and Room” and set the parameters for your speakers.
7. Connect the amplifiers to the correct outputs now specified in the menu
8. Select and press “Verify speakers”to check that speakers and amplifiers are correctly connected.
9. Adjust level(s) on your subwoofer(s) through the feature in the menu, ‘Adjust Sub’.
10. Measure and enter the distances to all speakers
11. Run the RoomPerfect™ Guided Setup.
12. Set up sources, audio preferences, stand-by state, zone b, etc.
13. Save and make a backup of the calibration and settings.

Lyngdorf Audio MP-60 –Owner’s manual 11
Installation Via Installer Menu
Connect a screen to the MP-60 using any of the video output sockets on the back. Access the menu system
by pressing the Setup button on the remote control.
There are some differences between how the web interface and the Installer Menu. This
manual describes how to set up via the installer Menu interface.
Installation Via Web Interface
You will need a computer, and the MP-60 must be connected to a router of an existing network.
If you do not know the IP address of the MP-60 on your local network, the MP-60 supports Apple´s Bonjour
Discovery service, which must be on the computer with which you wish to set up the MP-60. The software is
included in the Apple MAC OS operating system (not iOS devices). For Windows operating systems, the
software can be found at http://www.apple.com/support/bonjour/
•Access the web menu by typing http://mp60.local/ in your browser.
•Or, press the OK button on the remote. Toggling through will display the IP address.
•Or, download the Lyngdorf Remote application. Under settings find the MP-60 connected to the
same network as the mobile device and select ‘Open Device in browser’.
Home Screen
The HOME screen refers to the daily operation as performed with the remote control and displays selected
input and formats. This page shows information as to audio and video inputs and formats, and you can
control the volume level or Mute the sound. These settings will be reset to default values, when the MP-60 is
turned into stand-by mode.
You can switch between Sources, change Voicings, RoomPerfect™ focus point Post Processing as well at
activating Loudness function and adjusting Lip-sync.
Post Processing allows you to choose between following tools:
•Dolby Upmixer / Up-mixes all type of signals to use all existing speakers using Dolby’s techniques.
•Neural:X / Up-mixes all type of signals to use all existing speakers using DTS’ techniques.
•Auro-3D Auromatic / Decodes Auro 3D signals and up-mix all type of signals to use all existing
speakers using Auro’s techniques.
•Auro-2D / Up-mixes stereo signals to use surround sound speakers using Auro’s techniques.
•Auro-Stereo / Downmix of multi-channel signals to stereo using Auro’s techniques.

Lyngdorf Audio MP-60 –Owner’s manual 12
•Auro-Native / Decoding of 2D Auro formats –other signals are passed through
•Virtual:X / Creates a virtual surround sound effect from a stereo setup
•Stereo / Downmix of multi-channel signals to stereo.
•Party / Distributes a full-range signal to all channels
Loudness management turns on ‘Late Night’ functions dedicated to the specific formats being decoded.
These functions are managed individually in the setup menu: Audio Setup / Audio Processing.
Lip-sync settings will delay the sound processing in order to have correct synchronization with the screen
images. With a general audio offset, you should adjust the lip-sync on the specific Source settings in the
Setup menu.
The interface for controlling the built-in media streamer is found in the bottom section of this page. For
information as to the use of the interface see section for Streaming Setup.

Lyngdorf Audio MP-60 –Owner’s manual 13
Setup
The SETUP screen refers to all basic settings and option in the installation of the processor.
Source Setup
In the Source menu, you will find a list related to the input connectors. This register is though very flexible as
a Source can be specified to use individual inputs for audio and video. This means that several sources can
relate to the same input connectors –and vary in relation to the content, like ‘Action Movie’ and ‘Music Video’
being identical in connections, but differ in Post Processing setting, Voicing filter and trigger action.
Add / Edit Source
Source name
Input your personal reference for the source.
Lipsync offset (ms)
Set delay time in milliseconds to ensure that the video and audio signals are played back simultaneously.
Volume offset (dB)
Enables you to match input levels from different sources.
Audio input
Select the audio input connector. If you want the audio input to match the video input from an HDMI source,
select HDMI Audio. If you want to create a Source using the built-in radio player, you should choose Internal
Player, which will activate the selection of Preset vTuner stations.

Lyngdorf Audio MP-60 –Owner’s manual 14
Default postprocessing
Select the postprocessing mode, which is found most suitable for content on this Source
Default voicing
Select the voicing for this source, which is found most suitable for content on this Source
Video input
Select the input connection for this Source
Trigger out
Choose which trigger output to activate when using this Source. (The interface for controlling the triggers is
found in the Trigger Setup under System Configuration)
Preset vTuner station
Selects stored presets of the vTuner Internet radio station. (The interface for controlling the built-in media
streamer with vTuner is found in the bottom section of the HOME page)
To save changes, you must press “SAVE”after making changes to each source. Do not
go to the next input before saving changes.
Arrange Sources
Change the order through Screen Setup menu by:
•Highlighting it
•Moving it out of the stack by pressing right on the remote
•Moving the source by pressing up/down
•Reinserting it by pressing left.
Change the order through website menu by:
- Grab the symbols with the mouse and move this source to the desired position
Delete Source
Delete an enabled source through Screen Setup by highlighting it and pressing right on the remote.
In the web menu press Delete button.

Lyngdorf Audio MP-60 –Owner’s manual 15
Speakers and Room
You need to configure the MP-60 according to your speaker setup, setting the sizes of the speakers, so that
the Bass Management function can optimize the overall performance. In the setup page the connectors will
be highlighted with information as to signal type.
The purpose of the speaker setup is to tell the system which speakers and subwoofers are available and
how big the speakers are, which in turn reveals how much bass the speakers are capable of reproducing
(Bass cut-off frequency). The bass for each speaker channel is directed to the optimal output.
References to “speakers” in this document are specific to satellite or full-range speakers and do not include
subwoofers.
Speaker setup
As factory default the MP-60 is displaying a 7.1 speaker configuration as shown below:
The setup page is an overview of the available speaker outputs.
In order to correct the setup, you press EDIT CONFIGURATION, and by selecting each speaker or
subwoofer, you can specify size/bass cut-off and level.
Always SAVE the corrected setup before choosing another menu

Lyngdorf Audio MP-60 –Owner’s manual 16
Channel Designation
You should activate the speaker channels, which are in accordance with the DECODING FORMAT that you
want to optimize –you should NOT focus on the actual position of the speaker. (ex.: the first surround
speakers for a Dolby format are always LS and RS –also if they are positioned on the back wall). The
available speaker positions are:
Designations Channel Description
Subwoofers:
LFE Low Frequency Effects (Mono)
SUB L Left Channel Subwoofer (Stereo / does not handle LFE, if LFE Subwoofer is activated)
SUB R Right Channel Subwoofer (Stereo / does not handle LFE, if LFE Subwoofer is activated)
SUB RR Right Rear Channel Subwoofer
SUB LR Left Rear Channel Subwoofer
Low level speakers:
L Left (Bi-amping available, if AUX outputs are available)
R Right (Bi-amping available, if AUX outputs are available)
C Center
LS Left surround
RS Right surround
LRS Left rear surround (only available, if LS and RS are activated)
RRS Right rear surround (only available, if LS and RS are activated)
CB Center back
Speakers designated according to Dolby ATMOS and DTS:X specifications:
LW Left wide
RW Right wide
LTF Left top front
RTF Right top front
LTM Left top middle (only available, if RTF and RTM are activated)
RTM Right top middle
LTR Left top rear
RTR Right top rear
Speakers designated according to AURO 3D specifications:
HL Height left
HR Height right
HLS Height left surround
HRS Height right surround
HLR Height left rear surround
HRR Height right rear surround
HC Height center
TOP Top ceiling (aka: Voice of God)

Lyngdorf Audio MP-60 –Owner’s manual 17
Note:
A single (mono) subwoofer must be set as LFE subwoofer –no matter where you position it in the room
Sub Right and Sub Left is used in combination only, as it is used for a stereo setup –but you can activate
both the LFE subwoofer and the Sub Right/Sub Left, which will direct the LFE signal to the dedicated
subwoofer and direct the bass from the speaker channels to the Right and Left subwoofers.
LFE Channel cut-off
LFE (Low Frequencies Effects) is an individual audio channel for bass effects. The LFE channel cut-off will
add a low-pass filter for the signal to this subwoofer. Apart from the standard settings you can create your
custom cut-off setting.
The MP-60 can decode up to 16 channels (including the LFE, Low Frequencies Effects), and the system will
inform you, if you try to activate more speakers than the MP-60 can process –or is trying to make a setup,
which cannot be handled due to the limitations set by Dolby, DTS or Auro. An error message will appear!
The errors could be:
Error trying to activate one or two rear surround speakers without any side surrounds. The initial surround
sound speakers must be a pair of side surround speakers (LS & RS) –no matter where you position them.

Lyngdorf Audio MP-60 –Owner’s manual 18
Error trying to activate top or height speakers without the lower level speakers. If you only can position
surround speakers in the ceiling, these must be designated as lower level surround speakers, as you are not
creating a 3-dimensional sound field.
As a rule of thumb, don´t make changes if you are not familiar with the consequences, and always make a
backup before trying out other speaker setup options. When you change a size of speaker, LFE cut-off or
any distance or delay settings, you need to do a new RoomPerfect calibration, as the interaction between
room and speakers are changed.
Dialog boxes for speaker option
Speaker Size
When selecting a speaker size, you set the bass-cut-off frequency, and the signal information below this
frequency will be sent to the subwoofer(s). By selecting CUSTOM, you can specify the cut-off frequency
directly.
Gain
If a specific speaker channel is significantly lower in level compared to the other channels, you should
decrease the gain on the highest channel to match the overall level of speaker output. (increasing gain on a
speaker channel might cause a speaker or subwoofer to distort at levels below 0 dB). Even levels ensures,
that the subsequent RoomPerfect™ calibration will run perfectly. (highest and lowest speaker levels are then
within the microphones optimal calibration levels)
Amplifier Delay

Lyngdorf Audio MP-60 –Owner’s manual 19
In case you pass this speaker through an amplifier or subwoofer with internal processing, you need to
compensate for this by entering the relevant delay in milli-seconds.
Note:
A simple D/A conversion will normally take around 0.5 ms, whereas a subwoofer with internal DSP
processing (room correction) could delay the signal by 2 ms or more. The delay is the same, if the DSP filters
are activated or not. We recommend that you do not activate room correction software in the subwoofer, as
this will stress the amplifier and driver of subwoofer.
Use Natural Roll-Off
By activating the Natural Roll-Off the speaker signal will not be affected by the Bass Cut-Off settings –but a
copy of the bass signal will be directed to the subwoofer(s). This is particularly relevant, if the frequency
limitation of the speaker is close to the Bass Cut-Off frequency.
Use Bi-Amping
This setting is available for the Left and Right front speakers only (LF and RF). This will copy the signal to
these speakers to a pair free outputs (if available), why you can use two amplifier channels to power each of
these speakers.
Dolby Enabled Speakers
This function refers to a setup, where the front, side or side speakers are with an up-firing speaker to imitate
a ceiling mounted speaker. Delay and gain can be set for these specific speaker channels. Dedicated
speakers for this purpose will feature a cue filter to improve the sensation that this sound is coming from the
ceiling.

Lyngdorf Audio MP-60 –Owner’s manual 20
Subwoofer options:
Enable or disable this subwoofer by using your mouse.
Gain
In a later process you will be guided through the level settings on your subwoofer. If the settings on the
subwoofer does not allow for full correction, you can increase the level here to match the input sensitivity of
your subwoofer.
Amplifier Delay
If your subwoofer features internal processing, you need to compensate for this by entering the relevant
delay in milli-seconds (ms).
Verify Speakers
This function will allow you to test if the amplifiers and speakers are connected correctly to the outputs of the
MP-60. Follow the directions on the screen.
Adjust Sub
As the subwoofers are handling the bass information from multiple speaker channels, it is essential that the
subwoofer(s) are aligned with each other and with the relevant speaker channels. Without alignment you risk
having an inferior performance due to stress on the subwoofer’s internal amplifier.
With one or more active subwoofer(s) connected to the MP-60, this menu will guide you into setting the
volume level on each subwoofer’s controls. Follow the instructions on the display to go through two phases:
1. Find the correct system volume to do the Subwoofer adjustment (tones through speakers)
2. Adjust the volume setting on each subwoofer for the RoomPerfect™ calibration.
Channel Gain
This menu will allow you as per your personal preferences to change the level of each speaker, in its
relations to the decoded signal. This means that if you prefer that some surround speakers are higher in
level with DOLBY decoded material only, you can adjust this without affecting the level of the speaker, when