Lynx SEDONA User manual

SEDONA READY TO FINISH FIRE PIT ASSEMBLY
INSTRUCTIONS
Fire Pit shown with oponal nishes

SEDONA by LYNX™ READY TO FINISH FIRE PIT ASSEMBLY INSTRUCTIONS
2 SEDONA by LYNX™ Ready to Finish Fire pit Assembly Instrucons
IMPORTANT SAFEGUARDS
CAUTION
Never aempt to li the re pit by the counter top as serious damage may occur.
Plan your re pit locaon prior to beginning any set up. The re pit must be installed and leveled in its nal locaon.
Moving the re pit once complete is not advised as damage may occur.
WARNING
Two to three people are needed to set up the re pit. Failure to do so may result in injury.
WARNING
Do not store or use gasoline or other ammable liquids in the vicinity of this or any other appliance.
Do not store an extra LP bole near the re pit.
Ready to Finish Fire pit Orientaon Conguraons
Le Hand Control Side Right Hand Control Side
With LDR418 Access Door installed

3 SEDONA by LYNX™ Ready to Finish Fire pit Assembly Instrucons
SEDONA by LYNX™ READY TO FINISH FIRE PIT ASSEMBLY INSTRUCTIONS
Congratulaons on your purchase of the SEDONA by LYNX™ Ready to Finish Fire pit. The
prefabricated unnished re pit can be assembled in no me at all. Minimal tools are
necessary for assembly. The re pit comes ready for you to add your own personal touch
in components, nishes and countertops.
Before you begin the re pit installaon you will need to plan ahead. Some things to consider:
Power Supply and Venng:
The Ready to Finish Fire pit is not pre drilled or cut for venng access. You will have to cut through the rear panel.
When creang a vent, we recommend 4” x 14” at the rear of tre pit. The vent should be near the top for natural
gas: closer to the boom if using LP gas. Cover vents with louvered stainless steel covers if desired.
Fire pit Orientaon:
While you have the opon of a le hand or right hand orientaon, consider posioning the re pit to take advantage
of natural wind breaks.
Leveling the Fire pit:
If the base is not level, adjust the legs before the top panels and tray are installed. If the re pit is not leveled
correctly the panels could be misaligned and cannot be adjusted once assembly is complete.
Assembling the Fire pit:
You will need a Philips head screwdriver to install the screws which hold the top panel in place.
If you have any quesons or comments please
contact Lynx Customer Care:
Lynx Professional Grills
7300 Flores Street.
Downey CA 90242
Lynx Customer Care 888.289.5969

SEDONA by LYNX™ READY TO FINISH FIRE PIT ASSEMBLY INSTRUCTIONS
4 SEDONA by LYNX™ Ready to Finish Fire pit Assembly Instrucons
Fire Pit Body Components
Each Ready to Finish Fire Pit includes a 15 lbs. bag of lava rock
approximately 1/2” -1/4” in size. Black/Grey in color.

5 SEDONA by LYNX™ Ready to Finish Fire pit Assembly Instrucons
SEDONA by LYNX™ READY TO FINISH FIRE PIT ASSEMBLY INSTRUCTIONS
Exploded Parts Diagram

SEDONA by LYNX™ READY TO FINISH FIRE PIT ASSEMBLY INSTRUCTIONS
6 SEDONA by LYNX™ Ready to Finish Fire pit Assembly Instrucons
NO. P/N DESCRIPTION QTY.
170478 PAN, ASSEMBLY, WLDMT 1
235919 COVER, IGNITER, FIREPIT 1
335788 COVER, CONTROL 1
470482 FACEPLATE, CONTROL, WLDMT 1
570479 MANIFOLD WLDMT 1
634106 LOGO, SEDONA SMALL 1
731773 KNOB, BURNER 1
810001 BEZEL, KNOB 1
931162 IGNITOR, 2 SPARK 1
10 35925 BATTERY HOLDER, MOD 1
11 35867 BURNER, RTF FIREPIT 1
12 35918 BRKT, FASTENER, BURNER TUBE 2
13 34103 VALVE, MAIN BURNER W/SPRING, RED 1
14 13013 ORIFICE, #41 S 1
15 31795 FTNG, ELBOW 90 DEG. 1/4" TUBE, BRASS 1
16 34038 FTNG, ELB 90, ADP, 3/8-27 F X 7/16-20 M 1
17 13054 ELBOW, 3/8" FLARE TO 1/2" FIP 1
18 32836 FLEX TUBE, S/S, 3/8" X 9" 1
19 35923 ELECTRODE, PRE BURNER, 30" MOD 1
20 31227 WIRE, GROUND, 11" 1
21 35924 WIRE, VALVE TO MODULE, IGNITER 1
22 32816 SCREW, #6-32 X 3/16, PHP, SS 2
23 34035 SCREW, #6-32 X 1/4, THP, SS 1
24 30751 SCREW, #6-32 X 1/2, FHP, SS 2
25 32389 SCREW, #8-32 X 1/4, THP, SS 9
26 33507 SCREW, #8-32 X 3/4, PHP, SS 2
27 33706 SCREW, #10-32 X 3/8, PHP, SS 2
28 14023 NUT, #10-40, SPEED, STEEL 2
29 32768 NUT, #10-32, INSERT, STEEL, ZINC 2
30 31059 WASHER, #10, ESL 1
31 35149 CABLE TIE, HI-TEMP, 4" AR
32 13026 LP REGULATOR W/36" HOSE 1
Fire Pit Parts List

7 SEDONA by LYNX™ Ready to Finish Fire pit Assembly Instrucons
SEDONA by LYNX™ READY TO FINISH FIRE PIT ASSEMBLY INSTRUCTIONS
Wiring Diagram
Dimensions

SEDONA by LYNX™ READY TO FINISH FIRE PIT ASSEMBLY INSTRUCTIONS
8 SEDONA by LYNX™ Ready to Finish Fire pit Assembly Instrucons
Step 1
Unpacking the Box
Remove the staples and binding straps from the outside of the box. From inside the box, remove the foam and
packing materials. Separate the re pit components from the box.
Step 2
Posion and Level the Base
Place the re pit base on a level surface in its nal locaon and proceed to verify
the re pit base is level it in all direcons. The boom panel has adjustable feet for
this purpose. DO NOT OMIT THIS STEP. If the base is not leveled correctly the re
pit will be misaligned.
Fire pit Base
(Level is not included)
Leveling Foot
Installaon

9 SEDONA by LYNX™ Ready to Finish Fire pit Assembly Instrucons
SEDONA by LYNX™ READY TO FINISH FIRE PIT ASSEMBLY INSTRUCTIONS
Step 3
Assembling the Top Panel
The top panel comes in two parts. Secure the right hand top panel to the base using two of the supplied four Philips
head screws (#32595) and two of the eight supplied washers (#14044) on the two far right posions of the panel.
Secure the panel to the center of the base with two of the supplied four Philips head screws (#14030) and two of
the eight supplied washers (#14044).
Installaon...connued
Repeat the same steps for the le hand top panel

SEDONA by LYNX™ READY TO FINISH FIRE PIT ASSEMBLY INSTRUCTIONS
10 SEDONA by LYNX™ Ready to Finish Fire pit Assembly Instrucons
Step 4
Installing the Control Panel
The re pit control panel drops right into the opening of the base once the two
top panels have been secured. You will need to connect the gas regulator to
portable gas tank.
Installaon...connued
Liquid Propane portable
tank regulator
Lighng Instrucons
Step 1: Make sure the gas valve on the tank is open.
Step 2: Start the spark igniter by pressing the knob, and turn the knob to light, while holding it down.
Step 3: Once ignion occurs, release the knob and adjust the temperature to your preference. If the burner does not light
In 4 seconds, wait 5 minutes for gas to dissipate and repeat step 2.

11 SEDONA by LYNX™ Ready to Finish Fire pit Assembly Instrucons
SEDONA by LYNX™ READY TO FINISH FIRE PIT ASSEMBLY INSTRUCTIONS
I. Limited Lifeme Warranty – Fire pit Frame Panels
The base, sides and counter-top of the re pit are warranted to be free from
defects in material and workmanship, when subjected to normal domesc
use and service, for a Lifeme. This warranty is limited to the repair or
replacement of the defecve parts.
II. Limitaons & Exclusions
1.This Warranty shall apply to products purchased and located in the United
States and Canada. Products must be purchased in the country where
service is requested.
2. Warranty applies only to the original purchaser and may not be
transferred.
3. Warranty is in lieu of all other warranes expressed or implied and all
other obligaons or liabilies related to the sale or use of its grill products.
4. Warranty shall not apply and Lynx is not responsible for damage resulng
from misuse, abuse, alteraon of or tampering with the appliance, accident,
hosle environment, are-up res, improper installaon, or installaon not
in accordance with the instrucons contained in this manual, or the local
codes.
5. Lynx shall not be liable for incidental, consequenal, special or conngent
damages resulng from its breach of this wrien warranty or any implied
warranty.
6. Some states do not allow limitaons on how long an implied warranty
lasts, or the exclusions of or limitaons on consequenal damages. This
warranty gives you specic legal rights and you may have other rights which
vary from state to state.
7. No one has the authority to add to or vary Lynx’s warranty, or to create
for Lynx any other obligaon or liability in connecon with the sale or use of
its products.
8. Limited to the replacement of defecve parts with the owner paying all
other costs including labor.
III. What is not covered: Lynx shall not be responsible
for and shall not pay for the following:
1. Installaon or start-up, damages or problems caused by
improper installaon or use;
2. Service by an unauthorized service provider;
3. Damage or repair due to service by an unauthorized service
provider or use of unauthorized parts;
4. Warranty does not apply to products installed in any
commercial or non-residenal applicaon. Examples of excluded
applicaons include, but are not limited to day care centers,
schools, bed and breakfast centers, churches, private clubs, re
staons, club houses, common areas in mul-family dwellings,
restaurants, hotels, nursing homes, food service locaons and
instuonal food service locaons.
5. To correct normal adjustments or sengs, due to improper
installaon, commissioning or local gas supply properes;
6. Shipping and handling costs, export dues, installaon, removal,
or re-installaon cost.
7. Display models are generally sold “as is.” If you have purchased
a display model, please be advised that it is sold “as is” and that it
is subject to the following warranty exclusions: any exterior or
cosmec damage is non-warrantable; any missing components will
be replaced at consumers expense; major handling damage to
manifold, valve and ignion system will be serviced at consumer’s
expense; all other warranty’s (standard warranty) will remain in
eect.
8. The cost of a service call to diagnose trouble.
TM
SEDONA by LYNX Ready to Finish Fire pit Limited Warranty

P/N: 35931
The best outdoor kitchen products come from:
Lynx Grills, Inc.
7300 Flores Street
Downey, CA 90242
For more informaon please call,
1-888-289-5969 or visit www.lynxgrills.com