Lynx yellobrik ORR 1402 User manual
yellobrik Quick
Reference
yellobrik ®
®
We are constantly adding additional yellobrik modules.
Please visit our website for the latest product updates.
www.lynx-technik.com
LYNXTechnik AG Broadcast Television Equipment
®
RX2 Data
Present
RX1 Data
Present
Power
ORR 1402
Dual Channel 12G Fiber to SDI Receiver
Technical Specifications
Optical Inputs 2 x ber optic Inputs
Duplex (Singlemode) using LC/PC Connectors
SMPTE 2082-1, SMPTE 2081-1, SMPTE 424M,
SMPTE 292M; SMPTE 259M
Input range (wavelength) 1260nm to 1620nm
RX sensitivity: -9dBm @ 12Gbit/s
-10dBm below Gbit/s
2x RX data present LEDs on side of module
SDI Outputs 2 x SDI video on 75 Ohm BNC connector
SMPTE 2082-1, SMPTE 2081-1, SMPTE 424M,
SMPTE 292M; SMPTE 259M
Multi-standard operation from 270Mbit/s to 12Gbit/s
Return Loss: >15dB up to 1.5GHz ; >10dB up to 3GHz ;
>7dB up to 6GHz ; >12dB up to 12GHz
Power
LC Fiber Optic
Inputs (2)
SDI Video
Outputs (2)
DC Power Input
+12V DC @ 1.9W nominal - (power supply included)
(supports 7 - 24V DC input range)
Power LED on side of module
RX1 RX2
Dual Fiber to SDI
Receiver
12V 0V
О
Power
12G
6G/3G/1.5G
LYNXTechnik AG
OUT
1
OUT
2
Power
The module requires a clean 12V DC (7-24V DC) power source. An LED is
provided to conrm power is connected. A 12V DC power supply is
included with the module. If you are applying your own power source,
please provide a clean, 7-24V DC power source. Power consumption
information can be found in the technical specications table.
Note: ORR 1402 is identical in terms of mounting and securing
Connections
The SDI Video outputs are connected to the corresponding 75 Ohm
BNC connections provided.
The ber connection is made with a duplex
LC connector as indicated on the module. An example of a duplex LC
connector shown below.
Use the included dust plug to protect the optical connection from dust.
Operation
The ORR 1402 supports any SDI video signal from 270Mbit/s to
12Gbit/s. The ber input wavelength range is 1270nm - 1610nm and is
suitable for both basic ber (1310nm) and CWDM applications. Data
reception activity is indicated by the RX LEDs on the side of the module.
The module has two identical (and fully independent) channels.
Operation is fully automatic. The ber input video rates are
automatically detected, reclocked and provided on the BNC output
connectors. No user settings are provided for this module. The module
supports hot swapping and hot plugging of connections.
Note: I
f RX LED is OFF this indicates no signal is present, signal to weak or is a
non-valid input.
Note: The module is designed for use with SMF
(Singlemode) ber cable. While it is possible to
use Multimode cable, performance (distance) is
greatly degraded and not guaranteed.
Optional Mounting Brackets
The optional RFR 1001 mounting brackets can be
used to permanently mount the modules on any
at surface or on 19‘‘ rack rails.
Power Lead Strain Relief
The modules have a small hole in the case located above the power
connection to prevent the power lead being accidentally pulled out.
Use the supplied tie-wrap and secure the lead as shown below.
The optional RFR 1000-1 rack mount can be used to permanently
mount up to 14 yellobrik modules. In addition, the RFR 1000-1 can
provide full power redundancy for all mounted yellobriks.
Other Lynx Receiver manuals
