Lynx yellobrik ORX 1702-1 LC User manual

ORX 1702-1 (LC,ST,SC,MM)
Sync / Analog Video Fiber Receiver
Technical Specifications
Fiber Input
Singlemode
1 x ber optic Input
LC, ST or SC connection
SMPTE 297M - 2006
Input range (wavelength): 1260nm to 1620nm
RX sensitivity: -3dBm to -19dBm
RX active LED on side of module
Fiber Input
Multimode
1 x ber optic input
LC connection
SMPTE 297M - 2006
Input range (wavelength) 780nm to 880nm
RX sensitivity: 0dBm to -15dBm
RX active LED on side of module
Analog
Output
Sync = analog black burst / SDTV bi-level / HDTV tri-level
Video = NTSC / PAL composite video
2 identical outputs provided. 75 Ohm BNC connectors
NTSC SMPTE 170M, PAL CCIR624
Analog tri-level sync SMPTE ST 274, ST 296
720p, 1080i 50/59.94/60
1080p 23.97/24/25
1080psF 23.97/24
Return loss: 46.5dB to 10MHz
Power +12VDC @ 3.5W nominal - (supports 8 - 24VDC input range)
Analog (SD) Video
or Sync Outputs
SDTV Mode
(Video/Sync)
DC Power Input
LC
Singlemode
ST
Singlemode
SC
Singlemode
LC
Multimode
Fiber Output - Four options are available
HDTV Mode
(Sync)
Fiber
RX Active
Status LED
Factory Reset
(through hole)
USB Port
(F/W updates + control)
LYNXTechnik AG
LYNXTechnik AG Broadcast Television Equipment
®
yellobrik
®yellobrik Quick
Reference
®
We are constantly adding additional yellobrik modules.
Please visit our website for the latest product updates.
www.lynx-technik.com

Power Lead Strain Relief
The module has a small hole in the case located above the power
connection to prevent the power lead being accidentally pulled out.
Use the supplied tie-wrap and secure the lead as shown below.
Connections
The analog video / sync outputs use standard BNC video connectors.
Two identical outputs are provided.
Four versions of the module are available, the only dierence is the SFP
sub module installed into the basic module. (LC, ST or SC connections
for singlemode versions and a mutlimode version with LC connection)
The module ber connection is supplied with a rubber plug installed,
this is to prevent dust contamination. Please retain the plug and use if
the cable is ever disconnected from the module.
Operation
Operation of the ORX 1702-1 is fully automatic. The ber input is
automatically detected and converted to an analog sync signal. The
modules current operating standard (SDTV or HDTV) can be seen using
the LED’s on the side of the module.
Note: The default mode of operation is to output a sync signal. If SDTV (525 or
625) video is received, then only the analog sync will be converted. To convert
the entire SDTV video signal requires an internal setting is changed using the
yelloGUI software tool.
When using a OTX 1712-2, or OTX 1742-2 as the ber transmitter the
timing latency (from analog input to output) is EXACTLY 1 frame for
sync.
For video signals is it less than one frame, but not frame aligned.
Status LED
The status LED on the top of the module is multifunction:
= Power OK and no internal programmed settings are present
= Power OK and some internal programmed settings are active*
= (out) Power not present
* Some additional internal settings have been made using the yelloGUI. The LED indicates this by
turning yellow. The module can be reset to factory defaults by using the reset switch (recessed
under a hole on the side of the module). When reset the LED will change back to green.
USB Port / Firmware Updates / yelloGUI
The USB interface on the module is used for rmware updates and for
control of the module using the yelloGUI software application.
To update a yellobrik, power it and connect it to the PC or Mac running
the yelloGUI software with the provided USB cable. The yelloGUI
software will indicate if a new rmware is available for the connected
module and will guide you through the update process.
Firmware updates are always free of charge.
For more information and to download the yelloGUI application please
goto: http://yellogui.lynx-technik.com
Optional Mounting Bracket
The optional RFR 1001 mounting bracket can be
used to permanently mount the module on any
at surface or on 19” rack rails.
Note: ORX 1702-1 is identical in terms of mounting and securing.