M-Elec Nox Series User manual

V4
Floodlight Range
10-50W with Plug
Product information
The NOX range 10-50W floodlight is our latest development of the iconic
LED Floodlight range. Featuring a plug option & ultra efficient offset bracket
that installers demand. Super slim body and illumination specifications that lead
in the floodlight category. NOX V4 is the brighter choice by far. Supported by a
M-Elec 7 year warranty.
NOX1, 15W NOX2, 20W
NOX MINI, 10W NOX5, 50W
NOX3, 30W
OUR FULL RANGE Available in Warm White and White Models with plugs
TECHNICAL INFORMATION










Total Power: 10W* 15W* 20W* 30W* 50W*
Lumen Output: WW 1203lm
W1206lm
WW 1823lm
W1910lm
WW 2572lm
W2645lm
WW 4102lm
W4110lm
WW 6400lm
W6484lm
Colour Temp: WW 3000K
W5700K
WW 3000K
W5700K
WW 3000K
W5700K
WW 3000K
W5700K
WW 3000K
W5300K
IP Rating: IP65 IP65 IP65 IP65 IP65
Impact Rating: IK IK IK IK IK
 WW 120lm/W
W120lm/W
WW 122lm/W
W127lm/W
WW 121lm/W
W125lm/W
WW 135lm/W
W136lm/W
WW 131lm/W
W133lm/W
CRI: 70+ 70+ 70+ 70+ 70+
Beam Angle: 120° × 90 120° × 90 120° × 90 120° × 90 120° × 90
Temp Range: ° to 4° ° to 4° ° to 4° ° to 4° ° to 4°
Dimmable: No No Yes (0-10V min 30%) Yes (0-10V min 30%) Yes (0-10V min 30%)
 V AC Towin
Driver
V AC Towin
Driver
100-277V AC Towin
Dimmable Driver
V AC Towin
Dimmable Driver
V AC Towin
Dimmable Driver
Average Life: 50,000 hrs** 50,000 hrs** 50,000 hrs** 50,000 hrs** 50,000 hrs**
Max Current

A A A A A
Power Factor > > > > >
Dimensions:
W× H× D:
148x128x45mm 148x128x45mm 216x190x50mm 216x190x50mm 247x238x52mm
Weight: 0.56kg 0.58kg 1.15kg 1.16kg 1.63kg
Construction: ADC12 Aluminium heat sink
with Akzo Nobel powder
coating & PC lens
ADC12 Aluminium heat sink
with Akzo Nobel powder
coating & PC lens
ADC12 Aluminium heat sink
with Akzo Nobel powder
coating & PC lens
ADC12 Aluminium heat sink
with Akzo Nobel powder
coating & PC lens
ADC12 Aluminium heat sink
with Akzo Nobel powder
coating & PC lens
Kit Includes:  × LED Floodlight
 ×m flex  AU plug
 × User Manual
 × LED Floodlight
 ×m flex  AU plug
 × User Manual
 × LED Floodlight
 ×m flex  AU plug
 × User Manual
 × LED Floodlight
 ×m flex  AU plug
 × User Manual
 × LED Floodlight
m flex  AU plug
 × User Manual
*Total power consumed including driver
** Average life is calculated on expected average lifespan

Floodlight
PLEASE NOTE
 For further information about our Warranties please go to: melec.com.au/legal/warranties
MUST BE INSTALLED BY A LICENSED ELECTRICIAN
• Read instructions carefully before attempting to install the fitting. Retain this guide for future reference
• Disconnect power before installing or servicing
• This fitting is for outdoor use and should not be used in areas with limited ventilation or high ambient temperatures
• Do not extend low voltage cables from the output of power supply
• All components must not be mechanically stressed
• Be careful not to damage or destroy conductive paths on the circuit board
• Follow all relevant electrical and safety standards (including AS000)
• Correct electrical polarity must be observed as the wrong polarity may destroy the product and is not covered
under warranty
• Damage by corrosion will not be honoured as a material defect claim. It is the user’s responsibility to provide suitable protection against
corrosive agents such as moisture, condensation and other harmful elements
ACCESSORIES
Product Compatible Models
ML-NOXBOX-130 Quick install, IP65 rated junction box. All Models
ML-NOX3BKT Pole bracket NOX3
ML-NOX5BKT Pole bracket NOX5
 Spigot adaptor MLNOX3BKT, MLNOX5BKT
INSTALLATION GUIDE
1. Do not remove any part of the fitting.
2.Install fitting using correct equipment and components (eg.
Expansion bolts for masonry)
3. Connect with plug or using M-Elec's newest junction box
Noxbox™ (to be purchased separately) or other suitable
enclosure.
Min 90°
200mm
Max 155°
50mm
DIMMING CONNECTIONS
Please note: Do not connect anything other than
a 0-10V dimmer or control system or the warranty
will be void.
1.Open the light fitting.
2. Safely locate the purple (+) and grey (-)
0-10V dimming cables. Connect to your
0-10V dimming system (watch polarity).
3. Ensure you use suitable sealant/glands to
keep the IP rating.
4. Reassemble and ensure all seals are secure.
Water penetration from a failure to seal the
fitting properly will not be covered under
warranty.
Microwave Sensor or Other