M-Elec Nox Series Manual

TECHNICAL INFORMATION STANDARD MODELS
 
Total Power: MAX 150W*(POWER SELECTABLE 50W / 80W / 100W / 150W)
 20,403lm 20,421lm
 3000K 5700K
IP Rating: IP65
 145lm/W 143lm/W
CRI: 70+
Beam Angle: 120°x90
 ° to °
Dimmable: Yes 0-10V
 V AC Towin dimmable driver
Average Life: 50,000 hrs**
Max Current
 1.8 A
 >
IK Rating IK
Dimensions
 407x347x85mm
 4.53kg
 7 Years
 ADC12 Aluminum heat sink with Akzonobel power coating & PC lens
 1 x LED floodlight,
1 x 1m pre-stripped flex, 1x User Manual
50-150W LED FLOODLIGHT
Product information
The 

V4
 7
*Total power consumed including driver
** Average life is calculated on expected average lifespan
Perfect for use with NOXBOX™
Fast and Easy Wiring
INSTALLATION GUIDE
1. Do not remove any part of the fitting.
2. Install fitting using correct equipment and components (eg.
Expansion bolts for masonry)
3. Connect wires using M-Elec's newest junction box Noxbox™
(to be purchased separately) or other suitable enclosure.
Min 90°
200mm
Max 155°
50mm
L  Brown
N  Blue
E  Green/Yellow
V4

DIMMING CONNECTIONS
PLEASE NOTE
T. 1300 222 445 | www.melec.com.au For further information about our Warranties please go to: melec.com.au/legal/warranties
Please note: Do not connect anything other than
a 0-10V dimmer or control system or the warranty
will be void.
1. Open the back of the light fitting.
2. Safely locate the purple (+) and grey (-) 0-10V
dimming cables. Connect to your 0-10V
dimming system (polarity is important).
3. Ensure you use suitable sealant/glands to
keep the IP rating.
4. Refit the back plate and ensure all seals are
secure. Water penetration from a failure to
seal the fitting properly will not be covered
under warranty.
• Read instructions carefully before attempting to install the fitting. Retain this guide for future reference
• Disconnect power before installing or servicing
• This fitting is for outdoor use and should not be used in areas with limited ventilation or high ambient temperatures
• Do not extend low voltage cables from the output of power supply
• All components must not be mechanically stressed
• Be careful not to damage or destroy conductive paths on the circuit board
• Follow all relevant electrical and safety standards (including AS000)
• Correct electrical polarity must be observed as the wrong polarity may destroy the product and is not covered
under warranty
• Damage by corrosion will not be honoured as a material defect claim. It is the user’s responsibility to provide suitable protection against
corrosive agents such as moisture, condensation and other harmful elements
POWER SELECTABLE
Default set to max 150W. To select the power wattage:
1. Unscrew the cap before using the selectable power function.
2. Select the wattage by toggling the DIP switch 1, 2, 3 to select the corresponding power.
3. Screw the cap on after selection.
Microwave Sensor or Other
ACCESSORIES
 
 Quick install, IP65 rated junction box. All Models
 Lens NOX 8, NOX515, NOX1530
 Adjustable Spigot Bracket NOX8, NOX515, NOX1530 NOX3060
 Flat Surface Mounting Bracket NOX8, NOX515, NOX1530 NOX3060
 Microwave Sensor and Remote NOX8, NOX515, NOX1530 NOX3060
 PE Cell NOX8, NOX515, NOX1530 NOX3060