M-system R8-YVT4N User manual

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-9672 P. 1 / 6
INSTRUCTION MANUAL
BEFORE USE ....
Thank you for choosing M-System. Before use, please check
contents of the package you received as outlined below.
If you have any problems or questions with the product,
please contact M-System’s Sales Office or representatives.
■PACKAGE INCLUDES:
DC voltage output module..................................................(1)
■MODEL NO.
Confirm Model No. marking on the product to be exactly
what you ordered.
■INSTRUCTION MANUAL
This manual describes necessary points of caution when
you use this product, including installation, connection and
basic maintenance procedures.
POINTS OF CAUTION
■CONFORMITY WITH EU DIRECTIVES
• The equipment must be mounted inside a panel.
• The actual installation environments such as panel con-
figurations, connected devices, connected wires, may af-
fect the protection level of this unit when it is integrated
in a panel system. The user may have to review the CE
requirements in regard to the whole system and employ
additional protective measures to ensure the CE conform-
ity.
■GENERAL PRECAUTIONS
• Before you remove or mount the unit, turn off the power
supply and output signal for safety.
• Switches on the side of the module can be set for mainte-
nance only while the power supply is off. Do not access
them while the power is supplied.
■ENVIRONMENT
• Indoor use.
• When heavy dust or metal particles are present in the
air, install the unit inside proper housing with sufficient
ventilation.
• Do not install the unit where it is subjected to continuous
vibration. Do not subject the unit to physical impact.
• Environmental temperature must be within -10 to +55°C
(14 to 131°F) with relative humidity within 30 to 90% RH
in order to ensure adequate life span and operation.
■WIRING
• Do not install cables close to noise sources (relay drive
cable, high frequency line, etc.).
• Do not bind these cables together with those in which
noises are present. Do not install them in the same duct.
■AND ....
• The unit is designed to function as soon as power is sup-
plied, however, a warm up for 10 minutes is required for
satisfying complete performance described in the data
sheet.
INSTALLATION
■HOW TO MOUNT THE MODULE ON DIN RAIL
• I/O Module
A
B
Confirm that the locking clamps of the I/O module are set.
Insert the module in parallel to the next one while aligning
the grooves of both modules (A & B in the above figure).
Maintain it perpendicularly to the rail.
More I/O modules can be added in the same manner.
DC VOLTAGE OUTPUT MODULE
(4 points, non-isolated) MODEL
R8-YVT4N

R8-YVM4N
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-9672 P. 2 / 6
• Protective Cover
Groove
Hook
The protective cover is to be attached over the connected I/O
module at the right end.
Align the hooks on the cover with the grooves of the module
and slide it straight until the hooks are latched.
When removing the cover, pull it out while squeezing the
hooks inward.
■HOW TO UNMOUNT THE MODULE ON DIN RAIL
Release the locking clamps and pull out straight the mod-
ule.
• Removing an intermediate module
Caution !
1) Be careful not to hurt your hand by pointed edges of the
internal bus connector.
2) I/O modules cannot hold tightly on the DIN rail by them-
selves without power/network module.
Secure them to the position if necessary by using DIN
rail end plates.

R8-YVM4N
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-9672 P. 3 / 6
COMPONENT IDENTIFICATION
RUN
Function Setting
DIP SW
Terminator
DIP SW
12345678
SW4
SW3Term
■FRONT VIEW ■RIGHT VIEW
On
On
Status
Indicator LED
Output Status
Indicator LEDs
Internal Bus
Connector
Output
Connectors
Module Address Setting
Rotary SW
5
4
3
2
1
0
9
8
7
6
5
4
3
2
1
0
9
8
7
6
SW1
×10 CARD ADD. ×1
SW2
5
4
3
2
1
0
9
8
7
6
5
4
3
2
1
0
9
8
7
6
■INDICATOR LED
ID OPERATION FUNCTION
Status OFF Stopping
Green ON Valid host communication
Green Blinking Reading/writing configuration
Red ON Setting error
Red Blinking Parameter error
Output
Status
OFF Output data in the range
Red Blinking Output data out of range
■OUTPUT CONNECTOR ASSIGNMENT
Ao 1
1
AG
2
NC
3
NC
4
Ao 2
5
AG
6
NC
7
NC
8
Ao 3
9
AG
10
NC
11
NC
12
Ao 4
13
AG
14
NC
15
NC
16
PIN
NO. ID FUNCTION
1 Ao 1 Output 1 (+)
2 AG Output 1 (-)
3 NC Unused
4 NC Unused
5 Ao 2 Output 2 (+)
6 AG Output 2 (-)
7 NC Unused
8 NC Unused
9 Ao 3 Output 3 (+)
10 AG Output 3 (-)
11 NC Unused
12 NC Unused
13 Ao 4 Output 4 (+)
14 AG Output 4 (-)
15 NC Unused
16 NC Unused
■MODULE ADDRESS: SW1, 2
The left switch determines the tenth place digit, while the
right one does the ones place digit of the module address.
Address is selected between 0 to 30.
(Factory setting: 0)
Module Address Setting (x10)
Module Address Setting (x1)
5
4
3
2
1
0
9
8
7
6
5
4
3
2
1
0
9
8
7
6
■OPERATING MODE
(*) Factory setting
• Range: SW4-1, 4-2
Same setting for all channels. Use PC Configurator to set
independent ranges per channel.
OUTPUT RANGE SW4-1 SW4-2
-10 − +10V DC (*) OFF OFF
0 − 10V DC ON OFF
0 − 5V DC OFF ON
1 − 5V DC ON ON
• Output at the Loss of Communication: SW4-7
Same output for all channels.
OUTPUT AT THE LOSS OF COMMUNICATION SW4-7
Output Hold (*)
(last data correctly received is hold)
OFF
Stop output ON
Note 1: For Stop output, output fixed at -5% when configura-
tion mode is DIP switch setting.
Output fixed at scaling value at the loss of communica-
tion when configuration mode is PC.

R8-YVM4N
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-9672 P. 4 / 6
• Conguration Mode: SW4-8
CONFIGURATION MODE SW4-8
DIP switch setting (*) OFF
PC Configurator and communication ON
Note 2: Be sure to set unused SW4-3 through 4-6 to OFF.
■TERMINATOR DIP SW: SW3
TERMINATOR SW SW3
Without (*) OFF
With ON
PC CONFIGURATOR
The following parameter items can be configured with PC Configurator Software (model: R8CFG).
Refer to the users manual of the software for detailed operations.
■CHANNEL INDIVIDUAL SETTING
PARAMETER SETTING RAGNE DEFAULT SETTING
Output range -10 - 10 V DC -10 - +10 V DC
Lower range value -10.00 - +10 00 (V) -10.00 (V)
Upper range value -10.00 - +10 00 (V) 10.00 (V)
Fine zero adjustment -320.00 - +320.00 (%) 0.00 (%)
Fine gain adjustment -3.2000 - +3.2000 1.0000
Scaled range Zero -32000 - +32000 0
Scaled range Span -32000 - [phone]
Initial output at the startup (scaled range) -32000 - +32000 0
Fixed output at the loss of comunication (scaled range) -32000 - [phone]
■CHANNEL BATCH SETTING
PARAMETER SETTING RAGNE DEFAULT SETTING
Loss of internal bus communication detection time 0.0 – 99.9 (sec.) 1.0 (sec.)
Output function at the loss of communication Hold the last normally received data
Fixed output as specified
Hold the last normally
received data
Configuration mode DIP SW (OFF)
PC (ON)
DIP SW (OFF)
Note. Be sure to set SW4-8 to ON to configure output range and output at the loss of communication by the PC configurator.
Settings are programmed by the PC Configurator via the Power/Network Module.

R8-YVM4N
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-9672 P. 5 / 6
TERMINAL CONNECTIONS
Connect the unit as in the diagram below.
■EXTERNAL DIMENSIONS unit: mm [inch]
115 (4.53)
6 (.24)7 (.28) 6 (.24) 7 (.28)
DIN RAIL
(35mm wide)
(3 (.12)) (4 (.16))
12 (.47) 73 (2.87)
55 (2.17)
■CONNECTION DIAGRAM
INTERNAL POWER
INTERNAL BUS
EXC. SUPPLY *1
*1. Not used
OUTPUT CONNECTOR 1
1
2
4
3
5
6
8
7
9
10
12
11
13
14
16
15
Ao1
AG
Ao2
AG
NC
Ao3
AG
NC
NC
NC
NC
NC
AG
Ao4
NC
NC
OUTPUT 1
OUTPUT CONNECTOR 3
OUTPUT CONNECTOR 4
OUTPUT CONNECTOR 2
BUS CONNECTOR
OUTPUT 2
OUTPUT 3
OUTPUT 4

R8-YVM4N
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-9672 P. 6 / 6
WIRING INSTRUCTIONS
■TENSION CLAMP
Unit side connector: M-System’s product
Cable side connector: DFMC1,5/2-ST-3,5 (Phoenix Contact)
(included in the package)
Applicable wire size: 0.2 - 1.5 mm2
Stripped length: 10 mm
Recommended solderless terminal
• AI0,25-10YE 0.25 mm2(Phoenix Contact)
• AI0,34-10TQ 0.34 mm2(Phoenix Contact)
• AI0,5-10WH 0.5 mm2(Phoenix Contact)
• AI0,75-10GY 0.75 mm2(Phoenix Contact)
• A1-10 1.0 mm2(Phoenix Contact)
• A1,5-10 1.5 mm2(Phoenix Contact)