M-TI FREEDOM MICRO II HS User manual

FREEDOM MICRO®II MECHANICAL HIGH SECURITY
1
M0555 rev A ©2022 MTI All Rights Reservedwww.MTIGS.com | T:800.897.1350
Instructions & Videos:
AR: attar.store.mobiletechinc.com
COR: att.store.mobiletechinc.com
Product Ordering:
AR: attar.store.mobiletechinc.com
COR: att.store.mobiletechinc.com
Questions & Troubleshooting:
800.897.1350
Order Inquiries:
[email protected]
Product Manual for
FREEDOM MICRO®II HS
APPLE SHELF INSTALL
DO NOT REMOVE FROM STORE
Contents
1. Components And Accessories 2
2. Baseplate Options 3
3. Mounting Riser to Fixture 4
4. Speedbracket™ Merchandising 4
5. Speedbracket™ Removal 7
For additional support, please reach out to our
Contact Center at 800-897-1350
CONTENTS
WARNING: MTI products contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Proposition 65, California Health & Safety Code Section 25249.6 et seq. Visit oehha.ca.gov for more information.

Instructions & Videos:
AR: attar.store.mobiletechinc.com
COR: att.store.mobiletechinc.com
Product Ordering:
AR: attar.store.mobiletechinc.com
COR: att.store.mobiletechinc.com
Questions & Troubleshooting:
800.897.1350
Order Inquiries:
[email protected]
2
M0555 rev A ©2022 MTI All Rights Reservedwww.MTIGS.com | T:800.897.1350
COMPONENTS AND ACCESSORIES
SpeedBracket™
Through Hole Mounting
Freedom Micro®II Tool
Baseplate - Pre-installed
Freedom Micro®II Mechanical High Security
Riser and Puck

Instructions & Videos:
AR: attar.store.mobiletechinc.com
COR: att.store.mobiletechinc.com
Product Ordering:
AR: attar.store.mobiletechinc.com
COR: att.store.mobiletechinc.com
Questions & Troubleshooting:
800.897.1350
Order Inquiries:
[email protected]
3
M0555 rev A ©2022 MTI All Rights Reservedwww.MTIGS.com | T:800.897.1350
1
MOUNTING RISER TO FIXTURE
4
Feed OEM power cable through hole in fixture
Insert Freedom Micro®II position into the fixture, with
the power cable coming out of the riser exiting forward/
down.
3Align bottom plate to slot adapter.
2Run OEM power cable through the channel in the
baseplate. The riser will be installed into the fixture
“backwards” from what may seem like the normal di-
rection. Power cable device connector (Lightning) will
exit out the back of the riser
65 Secure the Freedom Micro®II position with the knob. Completed Riser Installation.

Instructions & Videos:
AR: attar.store.mobiletechinc.com
COR: att.store.mobiletechinc.com
Product Ordering:
AR: attar.store.mobiletechinc.com
COR: att.store.mobiletechinc.com
Questions & Troubleshooting:
800.897.1350
Order Inquiries:
[email protected]
4
M0555 rev A ©2022 MTI All Rights Reservedwww.MTIGS.com | T:800.897.1350
1
3
2
4
SPEEDBRACKET™ MERCHANDISING
Loosen the center screw on the universal bracket to
loosen the bracket arms.
Place the phone into the universal bracket.
Extend the bracket arms as far as needed. The bracket
arms move simultaneously in pairs (top & bottom, and
left & right).
Adjust the universal bracket to fit the device snugly.
Open the top and bottom bracket arms,
then the side arms, in that order.
1.
2.
2.
1.

Instructions & Videos:
AR: attar.store.mobiletechinc.com
COR: att.store.mobiletechinc.com
Product Ordering:
AR: attar.store.mobiletechinc.com
COR: att.store.mobiletechinc.com
Questions & Troubleshooting:
800.897.1350
Order Inquiries:
[email protected]
5
M0555 rev A ©2022 MTI All Rights Reservedwww.MTIGS.com | T:800.897.1350
7 8
65
SPEEDBRACKET™ MERCHANDISING
Tighten the center screw on the SpeedBracket™ to
secure the bracket arms in place around the device.
After tightening screw, wiggle the arms to ensure they
have fully engaged the lock teeth, then re-check screw
for tightness.
Place device back onto puck.
Rotate the device and bracket clockwise on the puck
until it locks into place.
*click*
Once OEM cable has been routed (page 3) plug into
device.

Instructions & Videos:
AR: attar.store.mobiletechinc.com
COR: att.store.mobiletechinc.com
Product Ordering:
AR: attar.store.mobiletechinc.com
COR: att.store.mobiletechinc.com
Questions & Troubleshooting:
800.897.1350
Order Inquiries:
[email protected]
6
M0555 rev A ©2022 MTI All Rights Reservedwww.MTIGS.com | T:800.897.1350
1
3
2
4Remove the SpeedBracket™ from the Freedom Micro®
II Puck, then release and remove the Freedom Micro®II
tool.
With the Freedom Micro®II tool held in the twisted
position, rotate the SpeedBracket™ counterclockwise.
Twist the Freedom Micro®II tool clockwise 45 degrees
and hold it in place.
Insert the crescent end of the Freedom Micro®II tool
into the opening to the right of the LED.
REMOVING SPEEDBRACKET™ FROM PUCK