M4TEC SpacePro User manual

SPR_INSTRUC_TU_DR_05.2016www.spacepro.co.uk/instructions-2/Page 1 of 6
V1
CONTENTS:
A1x Top panel
B 1x Side panel (left)
C 1x Side panel (right)
D5x Shelves
(4x for 4 drawers)
E 1x Plinth panel
FSoft close drawer runners
3 Drawer Unit
•3x left, 3x right
4 Drawer Unit
•4x left, 4x right
GSoft close clips
3 Drawer Unit
•3x left, 3x right
4 Drawer Unit
•4x left, 4x right
HDrawer backs
3 Drawer Unit
•x3
4 Drawer Unit
•x4
12x 12mm
Wood Screw
(16x for
4 drawers)
12x
Euro Screws
(16x for
4 drawers)
12x 35mm
Wood Screws
(16x for
4 drawers)
6x 7mm
Wood Screws
(8x for 4 drawers)
6x Handle
Screws (8x for
4 drawers)
28x
Cams
12x Cams
(16x for
4 drawers)
28x
Dowels
2x
Wall mounting
brackets
12x Push Dowels
(16x for 4 drawers)
We recommend you use the Wall
Mounting Brackets provided to fix the
Tower Unit to a wall (where possible).
This will prevent the unit being pulled
over. Use suitable fixings.
IDrawer sides (left)
3 Drawer Unit
•3x left
4 Drawer Unit
•4x left
JDrawer sides (right)
3 Drawer Unit
•3x
4 Drawer Unit
•4x
KDrawer bases
3 Drawer Unit
•x3
4 Drawer Unit
•x4
LDrawer fronts
3 Drawer Unit
•x3
4 Drawer Unit
•x4
M Drawer handles
3 Drawer Unit
•x3
4 Drawer Unit
•x4
Tower unit pack
Drawer pack
tower unit 3 & 4 drawers
•Tools: Screwdriver & Hammer
•Two person build
Recommended:
Assembly Instructions
(400 & 600mm wide)
Tower Storage Unit DIY Assembly Guide M4TEC by Bedrooms Plus, 2 Murray Court, Hamilton ML3 9SL • Tel: [phone]
Email: [email protected] • Web: www.m4tec.com

SPR_INSTRUC_TU_DR_05.2016www.spacepro.co.uk/instructions-2/
1 2
34
Apply to all panels (x5 – 3 drawers, x4 – 4 drawers).
Lay panels (B &C) on a flat surface. Fit cams & dowels to both panels.
Note: B panel shown
PLEASE NOTE THE 3 AND 4 DRAWER TOWER UNIT ARE THE SAME IN CONSTRUCTION. WE HAVE USED THE 3 DRAWER TOWER UNIT AS AN EXAMPLE.
Page 2 of 6
x4
x4
x12
x4
x2
Screw through holes shown on both sides.
Note: 6x for 3 drawers, 8x for 4 drawers.
5
x6
Tower Storage Unit DIY Assembly Guide M4TEC by Bedrooms Plus, 2 Murray Court, Hamilton ML3 9SL • Tel: [phone]
Email: [email protected] • Web: www.m4tec.com

SPR_INSTRUC_TU_DR_05.2016www.spacepro.co.uk/instructions-2/
PLEASE NOTE THE 3 AND 4 DRAWER TOWER UNIT ARE THE SAME IN CONSTRUCTION. WE HAVE USED THE 3 DRAWER TOWER UNIT AS AN EXAMPLE.
6 7
Page 3 of 6
Ensure cams are facing inwards.
8 9
Tower Storage Unit DIY Assembly Guide M4TEC by Bedrooms Plus, 2 Murray Court, Hamilton ML3 9SL • Tel: [phone]
Email: [email protected] • Web: www.m4tec.com

SPR_INSTRUC_TU_DR_05.2016www.spacepro.co.uk/instructions-2/
(Repeat on all drawer sides). (Repeat on all drawer fronts).
PLEASE NOTE THE 3 AND 4 DRAWER TOWER UNIT ARE THE SAME IN CONSTRUCTION. WE HAVE USED THE 3 DRAWER TOWER UNIT AS AN EXAMPLE.
10 11
Page 4 of 6
x2
x4
1 2 3
1– Lay drawer side (J) on a flat surface, insert the base (K) into the groove then hold the back panel (H) in-place. 2– Place the other drawer side (I) over the base and screw into the back panel (H).
3– Turn the drawer around and screw in panel (J) . (Repeat on all drawers).
12
Drawer back Drawer
back
Drawer
base Drawer base
Drawer side
Drawer side
Drawer side
x2
x2
MAKING THE DRAWERS
Tower Storage Unit DIY Assembly Guide M4TEC by Bedrooms Plus, 2 Murray Court, Hamilton ML3 9SL • Tel: [phone]
Email: [email protected] • Web: www.m4tec.com

SPR_INSTRUC_TU_DR_05.2016www.spacepro.co.uk/instructions-2/
Screw soft close clip into place.
Drawer shown from underneath. (Repeat on all drawers).
(Repeat on all drawers). (Repeat on all drawers).
PLEASE NOTE THE 3 AND 4 DRAWER TOWER UNIT ARE THE SAME IN CONSTRUCTION. WE HAVE USED THE 3 DRAWER TOWER UNIT AS AN EXAMPLE.
13 14 15
Page 5 of 6
x1
x2
x2
1
2
1 – Slide the drawers so that the prong goes into the hole in the back of the drawer.
2 – Pull the sliders forward, until you hear a click, repeat on both sides. Use two people to stand up right.
16
Tower Storage Unit DIY Assembly Guide M4TEC by Bedrooms Plus, 2 Murray Court, Hamilton ML3 9SL • Tel: [phone]
Email: [email protected] • Web: www.m4tec.com

SPR_INSTRUC_TU_DR_05.2016www.spacepro.co.uk/instructions-2/
PLEASE NOTE THE 3 AND 4 DRAWER TOWER UNIT ARE THE SAME IN CONSTRUCTION. WE HAVE USED THE 3 DRAWER TOWER UNIT AS AN EXAMPLE.
Page 6 of 6
USE SUITABLE
WALL FIXINGS
We recommend you use
the Wall Mounting
Brackets provided to fix
the Tower Unit to a wall
(where possible).
This will prevent the
unit being pulled over.
Use suitable fixings.
WALL MOUNTING
BRACKETS
Fix the Wall Mounting Bracket to both sides of the Tower
Unit. (Use suitable fixings when attaching to the wall).
x2
Tower Storage Unit DIY Assembly Guide M4TEC by Bedrooms Plus, 2 Murray Court, Hamilton ML3 9SL • Tel: [phone]
Email: [email protected] • Web: www.m4tec.com