MachPower NW-SP4-001 User manual

INSTALLATION
GUIDE

2

3
Thanks
for choosing
Mach Power
products

4

5
POE Products Introduction 4
1.1 Product Features 4
1.2 Panel Layout 4
Installation Instruction 6
2.1 Operation Cautions 6
2.2 Desktop Mounting 7
2.3 Rack Mounting 7
2.4 Making power connection 7
Contents

6
POE Switch
One AC Power Cord
User’s guide
Installation components and other accessories
Model Number Total Ports POE
ports POE Standards Power/port Total power
NW-SP4-001 4x10/100M PoE
1x10/100M 4IEEE 802.3af/at 15.4W/30W 45/65W
SW-UF4L4P-014 4x10/100M PoE
4x10/100M 4IEEE 802.3af/at 15.4W/30W 65W
NW-SP8-002 8x10/100M PoE 8IEEE 802.3af/at 15.4W/30W 150W
SW-UG4L4P-001 4x10/100/1000M PoE
4x10/100/1000M 4IEEE 802.3af/at 15.4W/30W 65W
SW-UG8P-008 8x10/100/1000M PoE 8IEEE 802.3af/at 15.4W/30W 150W
Packing List
POE Products Introduction
1.1 POE Products Introduction
1 POE Switches
Please open the product packaging box with care and check the following items shipped with
product:
Thanks for purchasing POE products
We mainly provide three types of POE products: POE switches.
Please read this user’s guide carefully before operating.
If any of the above items are missing or damaged, please contact your customer service repre-
sentative for assistance

7
Led indicator Description Led Led States Function
Power PWR Red ON The switch is powered on.
OFF The switch is powered off.
POE power POE Red
ON POE power supply works.
OFF No POE power supply.
Blinking
The POE port is failed or PD connection
is overloaded, please remove PDs and
reconnect after checking.
Data 10/100M
LINK/ACT Green
ON Port is connected successfully.
OFF Port is failed to connect or work abnor-
mally.
Blinking The port is processing data transmitting .
1.2 Panel Layout
NW-SP4-001
4x10/100M PoE ports +1x10/100M ports, Total power:45W/65W

8
SW-UF4L4P-014
4x10/100M PoE ports + 4x10/100M ports
LED Indicator is the same with NW-SP4-001 (above)
NW-SP8-002
8x10/100M PoE ports
LED Indicator is the same with NW-SP4-001 (above)
SW-UG4L4P-001
4x10/100/1000M PoE ports + 4x10/100/1000M ports

9
SW-UG8P-008
8x10/100/1000M PoE ports
LED Indicator is the same with SW-UG4L4P-001 (above)
Led indicator Description Led State Function
Power PWR Green ON The switch is powered on.
OFF The switch is powered off.
System SYS Green ON The system is starting.
Blinking The system works normally.
POE power POE Red
ON POE power supply works.
OFF No POE power supply.
Blinking
The POE port is failed or PD connection is
overloaded, please remove PDs and recon-
nect after checking.
Data
10/100M Yel-
low
ON Port is connected successfully.
OFF No 10/100M port connection.
1000M Green ON Port is connected successfully.
OFF No 1000M port connection.
ACT Green Blinking The port is processing data transmitting .

10
Installation Instruction
Please open the product packaging box with care and check the following items shipped with
product:
2.1 Operation Cautions
1. Don’t stock the device in damp environment or near water, to avoid water or moisture pene-
trating into the inner device.
2. Don’t put the device on a unstable box or desk, the device will get damaged from falling.
3. Please check and make sure the operation voltage is meet the voltage standard marked on the
device surface before the next steps.
4. Please use a grounded three-hole power socket in the rack or desk mounting, to mitigate
damage caused by electro-static discharge or lightning stoke.
5. Keep the device far from heat sources, strong power radio transmitters and radar transmit-
ters.
6. Similar with other electrical products, the semiconductor chip in device will get damaged when
open and shut off the power frequently. Please restart the device 3~5 seconds(or longer) after the
power is shut off.
7. Please pull out the power plug before cleaning the device. Don’t wipe the device with wet cloth
or clean the device with liquid.
8. To guarantee a long operation life, the device can only be used in indoor and in ventilated & dry
environment. And to get a good heat dissipation, please reserve a space over 10CM around the
device.
2.2 Desktop Mounting
1. Set the device( top- for bottom) over a large, stable and grounded desktop.
2. Attach the four adhesive feet on the four bottom corners ( some switches don’t have these
adhesive feet, please move to next step).
3.Turn around the device and set it stably on the desktop.
Note: Switches with less than 5 ports suitable for desktop mounting
2.3 Rack Mounting
Note: Generally, switches with 8 ports or more ports can be mounted in a standard 19-inch
equipment rack defined by Electronic Industries Association(EIA).
1. Please first attach the two L-shaped brackets to the device sides, using the screws provided in
the bracket mounting kit.
2. Mount the device in the rack, using rack mounting screws( not provided).

11
2.2 Making power connection
POE switches and POE Injectors is designed for AC 90～264V/50～60Hz Power Supply. We advise to
adopt a one-phase 3-wire power socket with neutral point joint or multifunctional computer pow-
er socket. Please make sure there are no problems on power supply, connection and grounding
before you start operating the POE devices, or the devices will get damaged.
Connecting Instruction:
1. Connect one end of power cord into the AC power socket of POE device rear panel, and then
connect the other end to the external AC power supply socket.
2. Check the “Power” indicator on the POE device front panel, the LED will be on if successfully
connected.
Neutral Point
Live LineNull Line