MadgeTech RTDTemp2000 Reference guide

MadgeTech, Inc.
PO Box 50 lWarner, NH 03278
Phone [phone] lFax 603.456.2012
www.madgetech.com l[email protected]
Red 485
Dark Blue Pantone 289
Light Blue 58% of Pantone 289
REV F 2010.04.12
To view the full MadgeTech product line,
visit our website at www.madgetech.com.
Red 485
Dark Blue Pantone 289
Light Blue 58% of Pantone 289
Product Information Card
RTDTemp2000
Product Quick Reference Card
RTDTemp2000
Precision RTD Based Temperature Recorder with LCD Display
Part Number RTDTemp2000
Temperature Sensor 100Ω Platinum RTD
Temperature Range -200 to +850°C
Temperature Resolution 0.01°C
Calibrated Accuracy +0.05°C (-200 to +260°C)
+0.3°C (+260 to +850°C)
Memory 174,762
Sample Rate 2 seconds up to 24 hours
Required Interface Package IFC110 or IFC200
Typical Battery Life 1 year @ 1 minute reading rate with display off, 30 days
typical with continuous LCD display use
Optional AC adapter available
Baud Rate 115,200
Operating Environment -20 to +60°C 0 to 95%RH (Non-Condensing)
Materials Black anodized aluminum
Dimensions 4.8” x 3.3” x 1.25” (122mm x 84mm x 32mm)
Approvals -
Specifications subject to change.
See MadgeTech’s terms and conditions at www.madgetech.com
Device Maintenance
Battery Replacement
Materials:
3/32” HEX Driver (Allen Key)
Replacement Battery (U9VL-J)
- Remove the cover from the device by unscrewing the four
screws.
- Remove the battery from its compartment and unsnap it
from the connector.
- Snap the new battery into the terminals and verify it is secure.
- Replace the cover taking care not to pinch the wires. Screw
the enclosure back together securely.
Note: Be sure not to over tighten the screws or strip the threads.
Battery Warning
WARNING: FIRE, EXPLOSION, AND SEVERE BURN HAZARD. DO NOT
SHORT CIRCUIT, CHARGE, FORCE OVER DISCHARGE, DISASSEMBLE,
CRUSH, PENETRATE OR INCINERATE. BATTERY MAY LEAK OR
EXPLODE IF HEATED ABOVE 60°C (140°F).
Recalibration
The RTDTemp2000 standard calibration is two points, 50 Ωand
15 0 Ω.
Pricing:
Recalibration traceable to NIST $60.00
Recalibration $40.00
Additional:
As Found Data $15.00 per parameter/channel
Verification Point $15.00 per point
To send the devices back, visit www.madgetech.com, select
Services then RMA Process.

RTDTemp2000 Product Quick Reference Card
Installation Guide
Installing the Interface cable
- IFC200, IFC202 or IFC300
Refer to the “Quick Start Guide” included in the package.
- IFC110, IFC102 or IFC103
Plug the serial cable into the port and verify it is secure.
- USB-1 or USB-101
Install the USB drivers from the CD provided in the kit, than
plug the USB cable into the computer and the serial cable into
the serial port.
Installing the software
Insert the Software CD in the CD-ROM Drive. If the autorun
does not appear, locate the drive on the computer and double
click on Autorun.exe. Follow the instructions provided in the
Wizard.
Connecting the data logger
- Once the software is installed and running, plug the interface
cable into the data logger.
- Click the Communication Menu, then Auto Configure Port.
- After a moment, a box similar to the following will appear;
- Click OK. The Device Status box will appear. Click OK.
- At this point, communications have been configured for your
logger. These settings can be found under the Communication
Menu.
Note: For additional installation instructions refer to your “Data
Logger & Software Operating Manual”.
KEY
1- Ref +
2- Measurement(-) Input
3- Measurement (+) Input
4- Excitation Current Out (+)
Wiring the Data Logger
Wiring Options
For 4-wire RTD probes, connect the four
lead wires to your RTD logger as shown
in the figures below.
For 3-wire RTD probes, short inputs 3
and 4 together, then connect the lead
wires to inputs 1, 2 and 3.
For 2-wire RTD probes, short inputs
3 and 4 together and inputs 1 and 2
together, then connect the RTD lead
wires to inputs 2 and 3.
Warning: Note the polarity instructions. Do not attach wires to
the wrong terminals.
Product Notes
Backlight
The backlight uses a significant amount of battery life. Refer to
the manual to configure the auto shut-off when not in use.
Device Operation
Starting the data logger
- Click Device Menu then Start Device.
- Choose the desired start
method.
- Choose the desired stop
method.
- Choose the start parameters
by selecting a Reading Rate
suitable for the application.
- Enter in any other desired
parameters and click Start.
- A box will appear stating
the data logger has been
started. Click OK.
- Disconnect the data logger from the interface cable and
place it in the environment to measure.
Note: The device will stop recording data when the end of
memory is reached or the device is stopped. At this point the
device cannot be restarted until it has been re-armed by the
computer.
Downloading data from a data logger
- Connect the data logger to the interface cable.
- Click the Device Menu then Read Device Data. This will
offload all recorded data onto the PC.
Technical Support
Visit www.madgetech.com, or call [phone].
Technical support is also available by e-mailing
[email protected]
Additional product information is available by e-mailing
[email protected].