Madimack ECO User manual

1

INDEX

a. FOREWORD
Thank you for choosing the Madimack high efficiency inverter pool heat pump!
All our heat pumps are built and designed to the highest standard and are protected by our extended
warranty service for peace of mind.
Warranty registration is required to be submitted online in conjunction with the commissioning page
and warranty registration page in the Appendix section at the back of the booklet
www.madimack.com.au/warranty-registration.
Please read and fully understand all information provided before attempting to install the pool heat
pump.
For technical questions and further information please contact [e-mail].
We hope you enjoy using our heat pumps.
Thank you!

COVER THE BASICS:
1. Check that you have received the package in good condition
2. Every residential heat pump comes with two accessory boxes and the manual. The manual will mention
all the parts and where they belong to make sure that the unit is commissioned, as per the 'commissioning'
section, and that adequate water flow rate is provided
3. Keep the surroundings of the unit clear of any debris, tree branches, and anything that can affect the
ventilation of the unit
4. Keep the invoice/packing slip in a safe place.
5. Register the unit for warranty as per the warranty section in this manual
6. Ensure that the unit is installed in an outdoor area, if it has to be indoors the unit will need to be ducted to
the outside
7. The condensate drain will need regular check-ups for any blockages or debris build ups,
Keeping it clean allows the condensate drain to escape easily to drainage
8. For Wi-Fi control make sure that you have full Wi-Fi strength in the heat pump area, more than
-50 DB is recommended for strong connection
9. Make sure that the unit is installed as per the ventilation diagrams to ensure efficient heating
rates

5
Safety
Precautions
b.

6
We have provided important safety messages in this manual for the installation, maintenance and repair of
your heater.
Please read thoroughly and obey all safety messages.
Environmentally friendly R32 Refrigerant is used in this heat pump.
1.Warning
This WARNING sign denotes a hazard. It calls attention to a procedure, practice,
or the like, which, if not correctly performed or adhered to, could result in
personal injury or injury to a third party. These signs are rare, but are extremely
important.
a. Keep the heat pump away from fire source.
b. Unit must be placed in a well-ventilated area; indoor or enclosed areas are not
allowed.
c. Repair and disposal must be carried out by trained service personnel
d. Vacuum the system completely before welding. Welding should only be carried
out by professional trained personnel.

7
2.Attention
a. Please read the following instructions before installation, use and maintenance.
b. Installation, must be completed only by competent persons only, and in accordance with this manual.
c. Check all water connections are sealed and tested before operating the machine
d. Except for the methods recommended by the manufacturer, do not use any methods to accelerate the
defrosting process or clean the frosted parts.
e. If a repair is required, please contact the nearest after-sales service center. The repair process must be
strictly in accordance with this manual. Repairs made by unauthorized persons may void the warranty.
f. Correctly set temperature required for personal preference making sure to avoid overheating or
overcooling.
g. Please do use or stack substances or other materials which may block the air flows to the inlet or
outlet areas. This causes the efficiency of the heater to be reduced, and may damage the machine.
h. Do not use or stock combustible gas or liquids such as thinners, paint and fuel, to avoid fire!
i. In order to optimize the heating effect, please install heat preservation insulation on pipes between
swimming pool and the heater, and please use a recommended cover on the swimming pool.
j. Connecting pipes of the swimming pool and the heater should be less than 10m.
3.Safety
a. Please keep the main power supply switch out of reach from the children.
b. If power is suddenly disconnected during operation, and later the power is restored, the heater will
start up automatically.
c. Please switch off the main power supply in high storm weather to prevent the machine from damage
that could be caused by lightning strikes.
d. Any repairs should be carried out in a well-ventilated area. Any source of ignition is prohibited during
the inspection.
e. Safety inspection must be carried before the maintenance or repair for heat pumps with R32 gas in
order to minimize the risk.
f. If R32 gas leaks during the installation process, all operations must be stopped immediately and call
your local service center.

8
About
your heat
pump
c.

9
1.Transportation
a. Always keep upright
b. Do not lift the water union
(Otherwise, the titanium heat exchanger may be damaged)
2.Accessories
Connection of the condensate drainage kit:
4 x Rubber Feet

10
3.Features
a. Stable DC inverter compressor
b. EEV Technology
c. High-efficiency twisted titanium heat exchanger
d. High pressure and low pressure protection
e. Soft start & wide voltage application
f. Stable inverter control system
4.Operating range
To provide you comfort and pleasure, please set swimming pool water temperature efficiently and
economically.
a. The heat pump can work between air -5°C～43°C,
b. Temperature of heating 18℃～40℃
Ideal operation range is between air 15°C ~ 25°C.
5.Introduction of different modes
a. The heat pump has three modes: Power, Perfect and Silence.
b. They have different strengths under different conditions.
Mode
Modes
Strength
Boost mode
Heating capacity: 20% to 100% capacity
Intelligent optimization
Fast heating
Silent mode
Heating capacity: 20% to 80% capacity
Sound level: 3dB (A) lower than Boost mode

11
6.Technical parameter
Model
ECO90/
240MM
ECO130/
240MM
ECO160/240
MM
ECO200/
240MM
ECO240/
240MM
PERFORMANCE CONDITION: Air 27°C/ Water 27°C/ Humid. 80%
Heating capacity (kW)
9.0
13.0
16.1
20.4
24.4
COP Range
6.4~10.8
6.3~11.0
6.2~10.9
6.3~11.0
6.3~11.0
PERFORMANCE CONDITION: Air 15°C/ Water 26°C/ Humid. 70%
Heating capacity (kW)
6.5
9.0
11.0
14.0
16.0
COP Range
4.4~6.4
4.7~6.4
4.3~6.6
4.3~6.4
4.5~6.6
TECHNICAL SPECIFICATIONS
Operating air
temperature
(℃)
-5℃~43℃
Rated input power
(kW)
0.28 ~ 1.55
0.41 ~ 2.01
0.50 ~ 2.56
0.60 ~ 3.26
0.72 ~ 3.81
Rated input current (A)
8
12.0
17.0
19.0
20.0
Sound level at 10m
dB(A)
21.6~33.5
23.9~34
26.2~37.3
26.3~38.1
26.9~38.7
Advised water flow
(L/min) ± 20%
50
75
90
120
150
Water connection
(mm)
40
Remarks:
This heat pump is able to perform normal within air temp -5°C ～ 43°C, efficiency will not be guaranteed out
of this range. Please take into consideration that the pool heat pump performance and parameters are
different under various conditions.
Related parameters are subject to adjustment periodically for technical improvement without further notice.
For details, please refer to nameplate.

12
7.Dimension
※ Above data is subject to modification without notice.
Please note the picture above and specification diagram of the pool heater is for the technician’s
installation and layout reference only. The product is subject to adjustment periodically for improvement
without further notice.








ECO90/240MM








ECO130/240MM








ECO160/240MM








ECO200/240MM








ECO240/240MM









13
Installation
Guidance
d.

14
Ventilation requirements
1st case: Single unit – 3 obstacles
Model number
ECO90
ECO130
ECO160
ECO200
ECO240
Option A
Distance A
(mm)
300
300
300
300
300
Distance B
(mm)
500
500
500
500
500
Distance C
(mm)
300
300
300
300
300
Option B
Distance A
(mm)
450
450
450
450
450
Distance B
(mm)
700
700
700
700
700
Distance C
(mm)
150
150
150
150
150
Please note that these are absolute minimum distances and where possible should always have a greater
difference. Under no circumstances should any of the distances be reduced as performance will be
affected. More ventilation is better.

15
4th case: Multiple units – 3 obstacles
Model number
ECO90
ECO130
ECO160
ECO200
ECO240
Option A
Distance A
(mm)
300
300
300
300
300
Distance B
(mm)
500
500
500
500
500
Distance C
(mm)
300
300
300
300
300
Distance D
(mm)
600
600
600
600
600
Option B
Distance A
(mm)
450
450
450
450
450
Distance B
(mm)
700
700
700
700
700
Distance C
(mm)
150
150
150
150
150
Distance D
(mm)
700
700
700
700
700
Please note that these are absolute minimum distances and where possible should always have a greater
difference. Under no circumstances should any of the distances be reduced as performance will be
affected. More ventilation is better.

16
Plumbing Multiple units:
Multiple heat pumps acting as one system should be connected in Cascade (Parallel Connection). Adequate
flowrate should be provided to all the units in the system to ensure efficient heating (Please refer to the
commissioning section in the manual to learn about heat pumps commissioning). The diagram below
represents the cascade connection

17
1. Installation reminder
Only competent persons are authorized to install the heat pump and should be educated with the relevant
building codes and standards of their current state or local governing body for all electrical, mechanical and
water services to prevent danger or damage to the unit.
a. Location and clearances
The inverter pool heat pump should be installed in a good ventilation place.
Please consult with your local service centre for indoor installation requirements
b. Typical installation diagram
Installations can differ dependent on-site conditions below is only a representation of one possibility.
Note: the inlet and outlet positions for the pipework is a representation only and can be positioned
differently.
Please see section: Installation options for more information of accessories available and different
plumbing layouts















18
2. Placing the unit and water connections
1) The frame must be fixed by bolts (M10) to concrete foundation or brackets. The concrete
foundation must be solid and fastened; the bracket must be strong enough and antirust treated;
2) Please don’t stack substances that will block air flow near inlet or outlet area, and there is no barrier
within 50cm behind the machine, or it will affect the efficiency of the heat pump and even stop the
machine;
3) The machine needs an appended pump (Supplied by the user). The recommended pump
specification-flux: refer to Technical Parameter, Max lift ≥10m;
4) When the machine is running, there will be condensation water discharged from the bottom, please
pay attention to it. Please hold the drainage nozzle (accessory) into the hole and clip it well, and
then connect a pipe to drain the condensation water out.
5) Please consult with your local service centre for indoor installation requirements.
3.Water pipe connection
The inlet and outlet water unions can’t stand the weight of soft pipes. The heat pump must be connected
by hard pipes!

19
4.Wiring requirements
a. Connect the heat pump to an appropriate power supply, the voltage should comply with the
rated voltage of the product.
b. The machine must be earthed
c. Wiring must be handled by a professional technician according to the circuit diagram.
d. Install electrical protection device according to local code for wiring
e. The layout of power cable and signal cable should be orderly and not affecting each other.
5.Electric wiring diagram
a. For power supply: 240V 50Hz
Note:
1) Must be hard wired, plug is not allowed.
1) The swimming pool heat pump must be earthed well.






20
6.References for protecting devices and cable
specification
※ Above data is subject to modification without notice.
Note: Above data is adapted to power cord < 10m. If power cord is 10m ~ 40m, the wire diameter must be
increased. The signal cable can be extended to 50m maximum.
Please see appendix for further wiring information including pump control and auxiliary input
MODEL












10
16
20
20
25



30
30
30
30
30