Maestro MICROTRACKER MT-01 Installation instructions

MICROTRACKER MT-01
PRODUCT SPECIFICATIONS & SOFTWARE MANUAL FOR VERSION 1.1
REV 0.2
WWW.MAESTRO-WIRELESS.COM
EMAIL:[e-mail]
TEL: [phone]
FAX: [phone]
ADDRESS: ROOM 3603-3609, 36/F, 118 CONNAUGHT ROAD WEST, SHEUNG WAN, HONG KONG

2Confidential, the whole document is the sole property of Maestro Wireless Solutions ltd.
3603-9, 36/F., 118 Connaught Road West, Sheung Wan, Hong Kong
[email protected]

Revision history
Rev. Date Details Originated by
0.1 21 October
2010 First release Samuel Chereau
0.2 15 November
2010 Proof Reading Pierre-Emmanuel Surga
This manual is written without any warranty.
Maestro Wireless Solutions Ltd. reserves the right to modify or improve the product and its accessories
which can also be withdrawn without prior notice.
Besides, our company stresses the fact that the performance of the product as well as accessories depends
not only on the proper conditions of use, but also on the environment around the places of use.
Maestro Wireless Solutions Ltd. assumes no liability for damage incurred directly or indirectly from
errors, omissions or discrepancies between the modem and the manual.
This software, solution or application is provided on an "as is" basis. No warranty whether expressed or
implied is given by Maestro Wireless Solutions Ltd. in relation to this software, solution or application.
User shall assume the entire risk of using or relying on this software, solution, application.
In no event will Maestro Wireless Solutions Ltd. be liable for any loss or damage including without
limitation, indirect or consequential loss, damage, or any loss, damage whatsoever arising from loss of
data or profit arising out of, or in connection with, the use of this software, application or solution. Every
effort is made to keep the software, application or solution up and running smoothly. However, Maestro
Wireless Solutions Ltd. takes no responsibility for, and will not be liable for, the software, application or
solution being temporarily unavailable due to technical issues beyond our control.
The above terms and conditions are subject to change without prior notice. The present use of this soft-
ware, application or solution implies the user approves and understands all the above terms and conditions.
Confidential, the whole document is the sole property of Maestro Wireless Solutions ltd.
3603-9, 36/F., 118 Connaught Road West, Sheung Wan, Hong Kong
[email protected]
3

4Confidential, the whole document is the sole property of Maestro Wireless Solutions ltd.
3603-9, 36/F., 118 Connaught Road West, Sheung Wan, Hong Kong
[email protected]

Contents
1 Product Specifications 11
1.1 PhysicalandMechanical ...................................... 11
1.2 Environmental ............................................ 12
1.3 PowerSupply............................................. 12
1.4 GSM/GPRS............................................. 13
1.5 Communicationwithbackend.................................... 13
1.6 GPS.................................................. 13
1.7 StatusIndicator............................................ 14
1.8 ElectricalInterface .......................................... 14
1.9 ServicePort ............................................. 14
1.10Functions&Features ........................................ 14
1.11Compliance.............................................. 15
2 Optional Accessories 17
2.1 Wireharness ............................................. 17
2.1.1 Specifications......................................... 17
2.1.2 10-pin connector assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.1.3 Standardwiringdiagram................................... 18
2.2 Externalbackupbattery....................................... 18
2.2.1 Specifications......................................... 19
2.2.2 /!\Warning .......................................... 19
3 Do and Do not 21
3.1 DO................................................... 21
3.2 DONOT................................................ 21
4 Step by Step - Quick Start Guide 23
4.1 Firstinstallation............................................ 23
4.2 Runatestinyourcar ........................................ 23
5 Software Manual 25
Confidential, the whole document is the sole property of Maestro Wireless Solutions ltd.
3603-9, 36/F., 118 Connaught Road West, Sheung Wan, Hong Kong
[email protected]
5

5.1 Introduction.............................................. 25
5.1.1 Overview ........................................... 25
5.1.2 Whichbuild?......................................... 25
5.1.3 Acronym use in this document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
5.2 Serveroriginatedcommands .................................... 25
5.2.1 Configurationcommands .................................. 25
SG101:SetserverSMSnumber .............................. 25
SG102: Set username, password, APN . . . . . . . . . . . . . . . . . . . . . . . . . . 26
SG103: Set port, IP address and protocol . . . . . . . . . . . . . . . . . . . . . . . . . 26
SG104: Select wired ignition or virtual ignition types . . . . . . . . . . . . . . . . . . . 27
SG105: Set FTP directory & FTP server login for DOTA . . . . . . . . . . . . . . . . . 27
SG106: Set port, IP address, username, password, APN, SMS number, and protocol 27
SG131: Query device firmware revision . . . . . . . . . . . . . . . . . . . . . . . . . . 28
SG132: Query connetion settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
SG133:QueryFTPsettings................................. 29
5.2.2 Commands for setting interval/threshold of report/alert . . . . . . . . . . . . . . . . . 29
SG201: Set ignition ON periodic location reporting & alert . . . . . . . . . . . . . . . 29
SG202: Set ignition OFF periodic location reporting & alert . . . . . . . . . . . . . . . 30
SG203: Set direction change threshold . . . . . . . . . . . . . . . . . . . . . . . . . . 30
SG204:Setspeedthreshold ................................ 31
SG205:SetMileageThreshold............................... 31
SG206: Set low battery detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
SG207: Set battery disconnect detection . . . . . . . . . . . . . . . . . . . . . . . . . 32
SG208: Set Heartbeat reporting / Power up alert . . . . . . . . . . . . . . . . . . . . . 32
SG209:Setidlealertperiod................................. 33
SG210:Settowalert..................................... 33
SG211: Sets commands from SG201 to SG210 in one, with profile name . . . . . . . 34
SG231: Query current interval, alert and threshold settings . . . . . . . . . . . . . . . 35
5.2.3 Commands for setting up geofence . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
SG301: Add rectangular geofence to device memory . . . . . . . . . . . . . . . . . . 36
SG302:SetCircularregion ................................. 36
SG303:SetPolygonregion................................. 37
6Confidential, the whole document is the sole property of Maestro Wireless Solutions ltd.
3603-9, 36/F., 118 Connaught Road West, Sheung Wan, Hong Kong
[email protected]

SG331: Query geofence settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
SG351:Deleteallgeofences ................................ 38
5.2.4 SMSnumberscreening ................................... 38
SG401,1: Set SMS number and enable screening . . . . . . . . . . . . . . . . . . . . 38
SG401,2: Query SMS number screening list . . . . . . . . . . . . . . . . . . . . . . . 39
SG401,3: Remove the SMS number screening list . . . . . . . . . . . . . . . . . . . . 39
SG401,0:Disablescreening ................................ 39
5.2.5 Generalactionscommands................................. 39
SG501:Resetthemodem ................................. 39
SG502: Erase entire non-volatile memory . . . . . . . . . . . . . . . . . . . . . . . . 40
SG503:UpdateFirmware ................................. 40
SG531: Read and report vehicle position immediately . . . . . . . . . . . . . . . . . . 40
SG532: Query diagnostics values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
SG533: Check GPS and Communication status . . . . . . . . . . . . . . . . . . . . . 42
SG551: Sets output for external starter relay . . . . . . . . . . . . . . . . . . . . . . . 43
SG552:SetBuzzerpattern ................................. 44
SG553: Initialize / set Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
SG554: Activate A-GPS Position Aiding . . . . . . . . . . . . . . . . . . . . . . . . . . 44
SG555: Change the voltage detection level for the virtual ignition . . . . . . . . . . . . 45
6 Event-triggered Periodic Reporting & Alert Message 47
6.1 MeaningofSyntaxFields ...................................... 47
6.2 Syntax#1:TCP/UDP/SMS ..................................... 48
6.2.1 Syntax #2: TCP/UDP/SMS – Geofence reports . . . . . . . . . . . . . . . . . . . . . . 49
6.3 Syntax#3:UDPwACK........................................ 49
7 Annex 51
7.1 Firmwareupdate........................................... 51
7.1.1 Byserialport......................................... 51
Condition ........................................... 51
Procedure .......................................... 51
7.1.2 DOTAprocess ........................................ 51
Condition ........................................... 51
Confidential, the whole document is the sole property of Maestro Wireless Solutions ltd.
3603-9, 36/F., 118 Connaught Road West, Sheung Wan, Hong Kong
[email protected]
7

Procedure........................................... 52
CostingofDOTAoperation ................................. 52
Possible reason of unsuccessful DOTA . . . . . . . . . . . . . . . . . . . . . . . . . . 52
7.2 GPSgoodfixalgorithm ....................................... 53
7.3 Powersavingmodebehavior .................................... 54
7.3.1 FunctionalDescription ................................... 54
7.3.2 Howitworks? ........................................ 54
7.4 Reports example for parser development . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
8Confidential, the whole document is the sole property of Maestro Wireless Solutions ltd.
3603-9, 36/F., 118 Connaught Road West, Sheung Wan, Hong Kong
[email protected]

Safety precautions
General precautions
–The modem generates radio frequency (RF) power. When using the modem care must be taken on
safety issues related to RF interference as well as regulations of RF equipment.
–Do not use your phone in aircraft, hospitals, petrol stations or in places where using GSM products is
prohibited.
–Be sure that the modem will not be interfering with nearby equipment. For example: pacemakers or
medical equipment. The antenna of the modem should be away from computers, office equipment,
home appliance, etc.
–An external antenna must be connected to the modem for proper operation. Only used approved
antennas with the modem. Please contact authorized dealer on finding an approved antenna.
–Always keep the antenna with minimum safety distance of 26.6cm or more from human body. Do not
put the antenna inside metallic box, containers, etc.
Using the modem in vehicle
–Check for any regulation or law authorizing the use of GSM in vehicle in your country before installing
the modem
–Install the modem by qualified personnel. Consult your vehicle dealer for any possible interference of
electronic parts by the modem.
–The modem should be connected to the vehicle’s supply system by using a fuse-protected terminal
in the vehicle’s fuse box
–Be careful when the modem is powered by the vehicle’s main battery. The battery may be drained
after extended period.
Protecting your modem
To ensure error-free usage, please install and operate your modem with care. Do remember the following:
–Do not expose the modem to extreme conditions such as high humidity/rain, high temperatures, direct
sunlight, caustic/harsh chemicals, dust, or water.
–Do not try to disassemble or modify the modem. There is no user serviceable part inside and the
warranty would be void.
–Do not drop, hit or shake the modem. Do not use the modem under extreme vibrating condition.
–Do not pull the antenna or power supply cable. Please attach or detach by holding the connector.
–Connect the modem only according to the instruction manual. Failure to do it will void the warranty
Confidential, the whole document is the sole property of Maestro Wireless Solutions ltd.
3603-9, 36/F., 118 Connaught Road West, Sheung Wan, Hong Kong
[email protected]
9

10 Confidential, the whole document is the sole property of Maestro Wireless Solutions ltd.
3603-9, 36/F., 118 Connaught Road West, Sheung Wan, Hong Kong
[email protected]

Chapter 1
Product Specifications
1.1 Physical and Mechanical
–Dimensions: 58.6 X 60.0 X 13.0 mm
–Weight: 45g
–Case: PC/ABS material UL94V-0 flammability
–Packing method:
•bulk packaging: protected in poly bags in bulk packing with leaflet
•individual packaging: protected in poly bag in individual gift box with leaftlet
Confidential, the whole document is the sole property of Maestro Wireless Solutions ltd.
3603-9, 36/F., 118 Connaught Road West, Sheung Wan, Hong Kong
[email protected]
11

–Exploded views
–Product label:
•IMEI: wireless module IMEI number
•Serial Number: SN#MT-01-<hardware version (2 digits)><lot number (2 digits)>-<production
date (yymmdd)>-<unit number (4 digits)>
1.2 Environmental
–ETSI compliant: -20 to +55 °C
–Operating temperature: -30 to +80 °C
–Storage: -40 to +85 °C
–Shock & Vibration: SAE J1211 compliant
1.3 Power Supply
–Supply voltage range: 6 to 32V DC
12 Confidential, the whole document is the sole property of Maestro Wireless Solutions ltd.
3603-9, 36/F., 118 Connaught Road West, Sheung Wan, Hong Kong
[email protected]

–Current consumption during idle: 58mA - typical at 12V DC
–Current consumption during transmission: 104mA - typical at 12V DC
–Current consumption during power saving: 8mA - typical at 12V DC
–Rated current: 650mA (peak value)
1.4 GSM / GPRS
–GSM/GPRS engine: Sierra Wireless branded Wireless Microprocessor / part number - WMP100
(approved by AT&T; CE, PTCRB and FCC certified).
–64Mb memory (6MB flash memory for embedded application; 2MB RAM)
–Frequency band: 850/1900MHz and 900/1800MHz
–Built-in GSM antenna: quad band
–SIM card interface: 1.8/3.0V
–SIM card holder: Flip type; SIM card is accessible from outside after removing a plastic lid
1.5 Communication with backend
–Configuration by SMS or GPRS1
–Configuration acknowledgment by SMS
–Communication with back-end (reports, alarms, replies ) by SMS, TCP or UDP connection over GPRS
1.6 GPS
–GPS engine: eRide Inc. branded / part number - CompactRide emD1000k
–Built-in active antenna:
Characteristic Specification
Center Frequency 1575.42±2 MHz
Bandwidth(10dB return loss) 10 MHz typical
Polarization R.H.C.P
–Filter / LNA:
Characteristic Specification
Center Frequency 1575.42±1.023 MHz
Gain 16±3dB (DC=3.0V)
Noise Figure 1.3dB typical (DC=3.0V)
Voltage 3.0±0.3V
Current(DC= 3.0±0.01V) 5.0±1mA
1as defined in Chapter 5
Confidential, the whole document is the sole property of Maestro Wireless Solutions ltd.
3603-9, 36/F., 118 Connaught Road West, Sheung Wan, Hong Kong
[email protected]
13

–Positioning accuracy: 7m outdoors (CEP 95%) and <20m indoors
–Supports GPS L1-band, C/A code
–High sensitivity down to -155.5dBm for both acquisition and tracking
–TTFF typically 3s when hot and <40s from cold (outdoors)
–Supports A-GPS position aiding
1.7 Status Indicator
–One red color LED indicating GPS position fix
–One green color LED indicating GSM registration
1.8 Electrical Interface
–10-pin connector2
–Connection for:
•Power supply (from vehicle battery)
•Primary digital output for driving external relay (“Starter Disabling”)
•Secondary digital output for driving additional relay or LED, etc. . .
•Primary digital input for ignition detection, active between 6 to 32Vdc
•Secondary digital input (reserved) , active between 6 to 32Vdc
•Analog input for sensor reading, maximum absolute rating. 5V, 20mA
–All digital inputs and digital outputs are opto-isolated and all interfaces are ESD protected.
1.9 Service Port
–Accessible from outside only after removing a plastic lid
–Serial port at logic 2.8V TTL level (UART) + other electrical test points
–Using external RS232 transceiver for connection to a computer for diagnostic and factory settings
1.10 Functions & Features
–Immediate on-request reporting of vehicle status (position, speed, mileage, ignition status, GSM
RSSI. . . )
–Periodic reporting of vehicle status (time and/or distance based)
–Call screening
2See section 2.1.2
14 Confidential, the whole document is the sole property of Maestro Wireless Solutions ltd.
3603-9, 36/F., 118 Connaught Road West, Sheung Wan, Hong Kong
[email protected]

–Disable or enable starter motor on-request
–Alert messages for over-speed, geofence crossed, main battery connect/disconnect, ignition on/off,
direction change, mileage exceed. . .
–Accept configuration (IP address, port number, APN,. . . ) & threshold settings from server
–Over The Air embedded software update
1.11 Compliance
–FCC Part 15B, 22H & 24E certification
–PTCRB certification
–CE (R&TTE directive)
–ROHS
Confidential, the whole document is the sole property of Maestro Wireless Solutions ltd.
3603-9, 36/F., 118 Connaught Road West, Sheung Wan, Hong Kong
[email protected]
15

16 Confidential, the whole document is the sole property of Maestro Wireless Solutions ltd.
3603-9, 36/F., 118 Connaught Road West, Sheung Wan, Hong Kong
[email protected]

Chapter 2
Optional Accessories
2.1 Wire harness
The wire harness has been designed for automotive grade.
2.1.1 Specifications
–10 pin molex connector
–In-line Fuse holder with glass fuse on the cable
–Relay socket
–Relay
Confidential, the whole document is the sole property of Maestro Wireless Solutions ltd.
3603-9, 36/F., 118 Connaught Road West, Sheung Wan, Hong Kong
[email protected]
17

2.1.2 10-pin connector assignment
Number Name I/O Description Color Remark
1 BAT+ I Battery backup power red
2 BAT- Battery backup ground black
3 PWR I Main power input red DC 6-32V
4 GND Main ground black
5 OUT1 O Output to drive the relay - Disabling the starter green 250mA max. sink current
6 DIN1 I Digital input - Use for the ignition sense white Active > 6V, max. 32V
7 DIN2 I Digital input - Reserved yellow Active > 6V, max. 32V
8 OUT2 O Digital output - Reserved blue 250mA max. sink current
9 ADC+ I Analog input orange max. 5V, 20mA
10 ADC- Analog input ground reference black
2.1.3 Standard wiring diagram
2.2 External back up battery
The back-up battery is designed as an optional add-on module and plugs directly on the wire harness.
It embeds its own charging circuit, a two cells Lithium Polymer battery and protection circuits in a single
housing.
18 Confidential, the whole document is the sole property of Maestro Wireless Solutions ltd.
3603-9, 36/F., 118 Connaught Road West, Sheung Wan, Hong Kong
[email protected]

In case the main power supply becomes unavailable, the MicroTracker will immediately switch to the back-
up battery as its power source. An alert can be send to signal the disconnection of the main power source
(which can happen in case of vehicle theft).
The battery can stand for around 5 hours of transmission, more than 2 days in power saving mode.
2.2.1 Specifications
–Voltage: 7.4V LiPo battery
–Capacity: 540mAh
–Connector: 2-pin molex
–Package: fiber glass
–Embedded charge circuit: will requires at least 8 hours of charge
2.2.2 /!\ Warning
The backup battery has been custom made, it includes a protection and charging circuit. Don’t try to use
any third-party battery on the wire harness connector.
Confidential, the whole document is the sole property of Maestro Wireless Solutions ltd.
3603-9, 36/F., 118 Connaught Road West, Sheung Wan, Hong Kong
[email protected]
19

20 Confidential, the whole document is the sole property of Maestro Wireless Solutions ltd.
3603-9, 36/F., 118 Connaught Road West, Sheung Wan, Hong Kong
[email protected]