MeiTrack iButton MVT600 User manual

File Name:
MEITRACK MVT600 User Guide
Creator:
Cavana Cheung
Project:
MVT600
Creation Date:
Update Date:
2010-09-13
2013-09-16
Sub Project:
User Guide
Page:
- 1 - of 25
Revision:
V3.1
Confidential:
External Documentation
MEITRACK® Vehicle GPS Tracker
User Guide
MVT600
Copyright © 2014 Meitrack Group All rights reserved.
- 1 -

File Name:
MEITRACK MVT600 User Guide
Creator:
Cavana Cheung
Project:
MVT600
Creation Date:
Update Date:
2010-09-13
2013-09-16
Sub Project:
User Guide
Page:
- 2 - of 25
Revision:
V3.1
Confidential:
External Documentation
Contents
1. Copyright and Disclaimer......................................................................... - 3 -
2. Applications........................................................................................... - 3 -
3. Product Function and Specifications .......................................................... - 3 -
3.1 Product Function ..................................................................................... - 3 -
3.2 Specifications........................................................................................... - 4 -
4. MVT600 and Accessories ......................................................................... - 5 -
5. View ..................................................................................................... - 6 -
6. First Use................................................................................................ - 6 -
6.1 Install SIM Card ....................................................................................... - 6 -
6.2 Charging ................................................................................................. - 6 -
6.3 LED Indications........................................................................................ - 7 -
6.4 Track by Calling........................................................................................ - 7 -
6.4.1 Multiple Phone numbers– A71............................................................ - 9 -
6.4.2 Listening-in (Voice Monitoring)–A72 ................................................... - 9 -
6.4.3 Sleep Mode – A73 ............................................................................ - 9 -
6.4.4 Geo-fence Alarm – B05................................................................... - 10 -
6.4.5 Set Anti-theft – B21................................................................. - 10 -
6.4.6 Time Zone– B35...................................................................... - 10 -
6.5 Configure by Computer ........................................................................... - 11 -
6.5.1 GPRS Tracking ............................................................................... - 13 -
6.5.2 Geo-fence Configuration ................................................................. - 13 -
6.5.3 Authorized Phone Number/GPRS Event............................................. - 14 -
6.5.4 GPRS Log...................................................................................... - 15 -
7Installation.................................................................................................. - 16 -
7.1 Install I/O Cable..................................................................................... - 16 -
Power/GND (PIN1/PIN2) ......................................................................... - 17 -
7.1.2 Digital Input (PIN4/5, negative triggering) ........................................ - 17 -
7.1.3 Digital Input (PIN3, positive triggering) ............................................ - 17 -
7.1.4 Output.......................................................................................... - 18 -
7.1.5r Input (PIN8/PIN10/PIN12)............................................................. - 18 -
7.1.6 Install Camera (RS232 Interface)..................................................... - 23 -
7.1.7 Install Camera (RS232 Interface) .......................................................... - 23 -
There’s a Micro SD card slot under the On/Off button. Micro SD card can be used to
store the pictures taken by the camera..................................................... - 24 -
7.1.9 Install RFID Reader (Wiegand Interface)........................................... - 24 -
7.2 Install GPS/GSM Antennas....................................................................... - 25 -
7.3 Mount the MVT600 unit........................................................................... - 25 -
Copyright © 2014 Meitrack Group All rights reserved.
- 2 -

File Name:
MEITRACK MVT600 User Guide
Creator:
Cavana Cheung
Project:
MVT600
Creation Date:
Update Date:
2010-09-13
2013-09-16
Sub Project:
User Guide
Page:
- 3 - of 25
Revision:
V3.1
Confidential:
External Documentation
1. Copyright and Disclaimer
Copyright © 2014 MEITRACK. All rights reserve
MEITRACK and are trademarks that belong to Meitrack Group
.
The user manual may be changed without prior notification.
This user manual, or any part thereof, may not be reproduced for any purpose whatsoever without the written
authorization of Meitrack Group (MEITRACK), or transmitted in any form, either electronically or mechanically,
including photocopying and recording.
In no event shall Meitrack Group (MEITRACK) be liable for direct, indirect, special, incidental, or consequential
damages (including but not limited to economic loss, personal injury, and loss of asset and property) arising out of
the use or inability or illegality to use the product or documentation.
2. Applications
Vehicle Real Time Tracking
Car Security/Anti-Hijack
Fleet Management
3. Product Function and Specifications
3.1 Product Function
U-blox 6 GPS and Quad Band GSM 850/900/1800/1900Mhz
AGPS ( with GSM Base Station ID)
Track by SMS/GPRS (MEITRACK Protocol)
Track on Demand
Track by Time Interval
Track by Distance Interval
Track on Mobile Phone
Listen-in or Two-way Audio (Optional)
Internal Flash Memory (8M)
Inbuilt Accelerating Sensor
Inbuilt Motion Sensor
Internal Backup Battery
SOS Alarm
Geo-fence Alarm
Copyright © 2014 Meitrack Group All rights reserved.
- 3 -

File Name:
MEITRACK MVT600 User Guide
Creator:
Cavana Cheung
Project:
MVT600
Creation Date:
Update Date:
2010-09-13
2013-09-16
Sub Project:
User Guide
Page:
- 4 - of 25
Revision:
V3.1
Confidential:
External Documentation
GPS Blind Area Alarm
Low Battery Alarm
Speeding Alarm
Over-the-Air Technology(OTA)
GPS Antenna Cut Alarm
External Power Cut Alarm
Mileage Report
Engine Cut (Engine immobilization)
Inbuilt Super Magnet (optional)
LED- Display(optional)
Camera (optional)
A52 Digital Temperature Sensor (optional)
A53 Resistive voltage-output mode fuel sensor (optional)
3 digital input
3 output
1 Input for Analog Detection
1 Analog Input for Fuel Detection
1 Input for Digital Temperature Sensor (Optional)
3.2 Specifications
Items Specifications
Dimension 103*98*32mm
Weight 220g
Input Voltage DC 11V~36V/1.5A
Back-up Battery 850mAh/3.7V
Power
consumption
65mA standby current
Operating
Temperature
-20℃~55℃
Humidity 5%~95%
Work T ime 36 hours in power-saving mode and 8 hours in normal mode
LED 2 LED lights to show GPS, GSM and other status
Button 1 SOS and 1 power on/off
Microphone Optional
Memory 8M Byte
Sensor V ibration sensor (for vibration wakeup )& acceleration sensor(auxiliary judgment of move
and standstill)
GSM Frequency GSM 850/900/1800/1900MHz
GPS Chip Latest GPS U-blox chipset, 50 channels all-in-view tracking
GPS Sensitivity -161dB
Copyright © 2014 Meitrack Group All rights reserved.
- 4 -

File Name:
MEITRACK MVT600 User Guide
Creator:
Cavana Cheung
Project:
MVT600
Creation Date:
Update Date:
2010-09-13
2013-09-16
Sub Project:
User Guide
Page:
- 5 - of 25
Revision:
V3.1
Confidential:
External Documentation
Positioning
Accuracy
10 meters
I/O 3 Digital Input ( 1 positive triggering and 2 negative triggering)
1 Analog Input Detection
1 Analog Input for Fuel Detection
1 Input for Digital Temperature Sensor
3 Output
4 RS232 Interface
4. MVT600 and Accessories
MVT600 with
Battery
GPS
Antenna
GSM
Antenna
I/O Cable +
SOS Button
USB Data Cable CD
Optional Accessories
Camera Handset
Phone
RFID
Reader
A21 LCD Player(dialing,
calling, show SMS)
A53 Fuel Sensor
A52 Digital Temperature Sensor +A61
sensor box
LED-Display
Copyright © 2014 Meitrack Group All rights reserved.
- 5 -

File Name:
MEITRACK MVT600 User Guide
Creator:
Cavana Cheung
Project:
MVT600
Creation Date:
Update Date:
2010-09-13
2013-09-16
Sub Project:
User Guide
Page:
- 6 - of 25
Revision:
V3.1
Confidential:
External Documentation
5. View
6. First Use
6.1 Install SIM Card
Check that the SIM has not run out of credit (test the SIM in a phone to make sure it
can send and receive SMS);
Check that the SIM Lock code is turned off;
If you require the function of sending an SMS location report to the authorized phone
number when it makes a call to the MVT600, please make sure the SIM installed
supports displaying caller ID.
Before installing the SIM card, turn off the power for MVT600.
Unscrew and remove cover.
Insert the SIM card by sliding it into the card holder with the chip module facing to
the connectors on PCB.
Replace the cover and screw it in.
6.2 Charging
Please connect GND (-Black) and Power (+Red) wires to 12V or 24 external power and make sure to charge the
battery for at least 3 hours.8 hours is highly appreciated.
Configuration and testing suggested be prior to installation.
GSM LED
GPS LED
On/Off
GSM Antenna
GPS Antenna
Mic./Speaker
SIM
Micro SD
USB Port
HandsetPower, I/O
Camera
Camera
RS232
RFID Reader
Copyright © 2014 Meitrack Group All rights reserved.
- 6 -

File Name:
MEITRACK MVT600 User Guide
Creator:
Cavana Cheung
Project:
MVT600
Creation Date:
Update Date:
2010-09-13
2013-09-16
Sub Project:
User Guide
Page:
- 7 - of 25
Revision:
V3.1
Confidential:
External Documentation
6.3 LED Indications
Press and hold the Power On/Off button for 3~5 seconds or connect external power supply 11-36V to turn on/off
MVT600.
GPS LED (Blue)
On One button is pressed or input is active.
Flashing ( every 0.1 second) Initializing or back-up battery power is low
Flashing (0.1 second on and 2.9 seconds off) MVT600 has a GPS fix
Flashing (1 second on and 2 seconds off) MVT600 has no GPS fix
GSM LED (Green)
On A call is coming in / a call is being made
Flashing ( every 0.1 second) Initializing
Flashing (0.1 second on and 2.9 seconds off) MVT600 is connected to the GSM network
Flashing (1 second on and 2 seconds off) MVT600 is not connected to the GSM network
6.4 Track by Calling
Make a call to MVT600 and it will report with one SMS.
For example,
Now,110727 02:48,V,16,23Km/h,61%,http://maps.google.com/maps?f=q&hl=en&q=22.540103,114.082329
&ie=UTF8&z=16&iwloc=addr&om=1
Click on the link then the location can be shown directly on Google Maps on your mobile phone.
Report description:
Now,110727 02:48,V,16,23Km/h,61%,http://maps.google.com/maps?f=q&hl=en&q=22.540103,114.082329
&ie=UTF8&z=16&iwloc=addr&om=1
GSM LED (green)
GPS LED (blue)
On/Off
Copyright © 2014 Meitrack Group All rights reserved.
- 7 -

File Name:
MEITRACK MVT600 User Guide
Creator:
Cavana Cheung
Project:
MVT600
Creation Date:
Update Date:
2010-09-13
2013-09-16
Sub Project:
User Guide
Page:
- 8 - of 25
Revision:
V3.1
Confidential:
External Documentation
Content Description Note
Now Current Location Alarm Type
110721 16:40 Date & Time: 21 July, 2011, 16:40pm Date & Time in YYMMDD HH:MM
V No GPS fixed GPS Status Indicator:
A = valid, V = invalid
10 GSM signal=10 GSM Signal. Decimal Digit (0~31)
0Km/h Speed=0 KM/h. Decimal digit
97% Battery Power: 97% Battery Power Balance (Percentage)
http://maps.google.c
om/maps?f=q&hl=en
&q=22.540103,114.0
82329&ie=UTF8&z=
16&iwloc=addr&om=
1
Latitude: 22.513015
Longitude: 114.057235
Google Maps Web Link with Latitude and
Longitude. Click on the link to get the
location.
If your mobile cannot visit HTTP websites, input the latitude and longitude into Google Maps as the following
picture shows to get the position:
More SMS commands
You can configure T1 by mobile phone or by computer using the Meitrack Manager.
For more details, please refer to part 6.5 Configure by Computer.
Note:
1. Password is 4 digits only and defaulted as 0000. You can change the password by using the Meitrack
Manager and SMS command.
2. MVT 600 will only accept commands and send SMS report from a user with the correct password.
If preauthorized phone number was set, only this phone number can receive the preset event SMS reports.
Copyright © 2014 Meitrack Group All rights reserved.
- 8 -

File Name:
MEITRACK MVT600 User Guide
Creator:
Cavana Cheung
Project:
MVT600
Creation Date:
Update Date:
2010-09-13
2013-09-16
Sub Project:
User Guide
Page:
- 9 - of 25
Revision:
V3.1
Confidential:
External Documentation
6.4.1 Multiple Phone numbers– A71
Command: 0000, A71, phone number 1, phone number 2, phone number 3
SMS Get: IMEI, A71, OK
Note：
Authorize a phone number for SOS alarm, calling for location report, geo-fence alarm, and low battery alarm.
Phone Number: Max 16 characters.
If no preset phone number, it is empty (default is empty).
Send command “0000, A71” to delete all phone numbers.
When the SOS button is pressed, MVT600 will make a call to phone number 1, 2 and 3. It will stop calling when
one number answers.
Example: 0000,A71,13811111111,13822222222,13833333333
SMS Get: 353358017784062,A71,OK
6.4.2 Listening-in (Voice Monitoring)–A72
Command: 0000, A72, phone number 1, phone number 2
SMS Get: IMEI, A72, OK
Note:
Authorize a phone number to make a silent call to the tracker. The tracker will answer the call automatically and
allows the caller to listen to what is happening around the tracker. There is no sound when the tracker is working.
Phone Number: 2 monitoring numbers at the most can be set, 16 characters per number.
If no preset phone number, it is empty (default).
If no phone number, but has “,”, the number related to this “,” is deleted.
Send command “0000, A72” to delete all phone numbers.
Example: 0000,A72,13844444444,13855555555
SMS Get: 353358017784062,A72,OK
6.4.3 Sleep Mode – A73
Command: 0000,A73,X
SMS Get: IMEI,A73,OK
Note:
This setting is for power saving.
X=0, turn off sleep mode (default)
X=1, normal sleep. GSM module work, the GPS will intermittent sleep. The device can work 25% longer than no
sleep mode. Note: this is not recommended for users who set “track by interval” or short time interval, because it
will affect the completeness of tracking.
X=2, deep sleep, the tracker will enter this mode after it is inactive or stationary(No SOS/any triggered by the
button/input/incoming calls/message/movement) for 5 minutes. GPS module stops working and GSM module
enters sleep mode. The tracker remains in this mode until it is activated by SOS/any triggered by the
button/input/incoming calls/message/movement. After that, it will repeat above processes.
Copyright © 2014 Meitrack Group All rights reserved.
- 9 -

File Name:
MEITRACK MVT600 User Guide
Creator:
Cavana Cheung
Project:
MVT600
Creation Date:
Update Date:
2010-09-13
2013-09-16
Sub Project:
User Guide
Page:
- 10 - of 25
Revision:
V3.1
Confidential:
External Documentation
Note: In any condition, the device will directly quit the sleep mode and back to normal working mode by SMS or
GPRS command to turn off the sleep mode.
Example: 0000,A73,2
SMS Get: 353358017784062,A73,OK
6.4.4 Geo-fence Alarm – B05
Command: B05,P,latitude,longitude,radius,in,out
SMS Get: IMEI,B05,OK
Note:
P: 1 to 8. Max 8 Geo-fence waypoints can be set.
Latitude: Latitude in decimal degrees of the waypoint center.
Longitude: Longitude in decimal degrees of the waypoint center.
Radius: [1, 4294967295] in meters.
In = 0, turn off the alarm when the tracker enters the waypoint;
In = 1, turn on the alarm when the tracker enters the waypoint.
Out = 0, turn off the alarm when the tracker exits the waypoint;
Out = 1, turn on the alarm when the tracker exits the waypoint.
Example: 0000,B05,1,22.91319,114.07988,1000,0,1
SMS Get: 353358017784062,B05,OK
Once the tracker goes outside of the circle (center: 22.91319,114.07988 and radius 1000 meters), the following
message will be received.
353358017784062,ExitGEO,22.918186,114.089823,080229123816,A,10,22,16,32,1,21,6667,850,,0000
6.4.5 Set Anti-theft – B21
Command: 0000,B21,Status
SMS Get: IMEI,B21,OK
Note:
Status=1, turn on Anti-theft (default); the device alarms when input 2 (negative input) and input 3 (positive input)
are active;
Status=0, turn off Anti-theft; the device doesn’t alarm when input 2 (negative input) and input 3 (positive input)
are active.
6.4.6 Time Zone– B35
Command: 0000,B35,T
SMS Get: IMEI,B35,OK
Note:
Default time of the tracker is GMT. You can use this command to change the time on your tracker to your local
time. This command is for SMS tracking only.
Copyright © 2014 Meitrack Group All rights reserved.
- 10 -

File Name:
MEITRACK MVT600 User Guide
Creator:
Cavana Cheung
Project:
MVT600
Creation Date:
Update Date:
2010-09-13
2013-09-16
Sub Project:
User Guide
Page:
- 11 - of 25
Revision:
V3.1
Confidential:
External Documentation
Time zone of SMS report is separated with that of GPRS data. If you need to set time zone in GPRS data, please
use SMS command: 0000, B36, T
T=0, to turn off this function.
T=[-32768,32767] to set time difference in minutes to GMT.
For those ahead of GMT, just input the time difference in minutes directly. For example, GMT+8,
W000000,032,480
‘-‘is required for those behind GMT. For example, W000000,032,-120.
Example: 0000,B35,480
SMS Get: 353358017784062,B35,OK
For more details regarding SMS commands, please refer to MEITRACK SMS Protocol.
6.5 Configure by Computer
This part mainly shows you how to use the Meitrack Manager.
Note: Don’t connect T1 to external battery when configuring.
Please refer to the Meitrack Manager Software for more information regarding configuration and functions.
Before using the Meitrack Manager, please first install USB driver and Meitrack Manager Software. For more
information , please read Meitrack Manager User Guide.
Run ‘PL2303_Prolific_DriverInstaller’ to install the driver for the USB data cable of MVT600.
Check if the USB driver is installed: Open Device Manager (right-click “My Computer” –“Manage” –“Computer
Management”- “Device Manager ” ) Click “Port(COM and LPT)”, and find “Prolific USB-to-Serial Comm Port” as
below. If ‘Prolific USB-to-Serial Comm Port’ cannot be found, you need to re-install the USB driver (for detailed
installation instructions, please refer to Meitrack Manager User Guide)
Note: Remember this Com number. It needs to be input into the Meitrack Manager. It is COM3 in this example and
it would be COM4 or COM5… in your computer.
Copyright © 2014 Meitrack Group All rights reserved.
- 11 -

File Name:
MEITRACK MVT600 User Guide
Creator:
Cavana Cheung
Project:
MVT600
Creation Date:
Update Date:
2010-09-13
2013-09-16
Sub Project:
User Guide
Page:
- 12 - of 25
Revision:
V3.1
Confidential:
External Documentation
Run ‘Meitrack Manager.exe’ and the following window will pop up:
The device is power on and the Meitrack Manager will automatically identify the device and enter into
configuration interface (column 1:Device) and display the default parameters.
Copyright © 2014 Meitrack Group All rights reserved.
- 12 -

File Name:
MEITRACK MVT600 User Guide
Creator:
Cavana Cheung
Project:
MVT600
Creation Date:
Update Date:
2010-09-13
2013-09-16
Sub Project:
User Guide
Page:
- 13 - of 25
Revision:
V3.1
Confidential:
External Documentation
Note: Meitrack Manager is in the CD. The language will be automatically adjusted to be the same as your PC
operation system’s language. Please use “Ctrl+L” to change the language.
6.5.1 GPRS Tracking
Select Column2: Tracking
To set GPRS parameters, Select this column to modify. Setup server IP and Port (Meitrack Server IP/Domain:
67.203.13.26, Port: 8800), APN, Time Interval, etc. This column is also used to setup SMS Tracking & monitoring
phone number.
For more details, please refer to Meitrack Manager User Guide.
6.5.2 Geo-fence Configuration
3Select Column 3: Geo Fence
Copyright © 2014 Meitrack Group All rights reserved.
- 13 -

File Name:
MEITRACK MVT600 User Guide
Creator:
Cavana Cheung
Project:
MVT600
Creation Date:
Update Date:
2010-09-13
2013-09-16
Sub Project:
User Guide
Page:
- 14 - of 25
Revision:
V3.1
Confidential:
External Documentation
Geo-fence: it is a circular fence which is based on a center point with preset radius. Maximum 8 geo-fence.
Enter Geo-fence: alarm while the device entering geo-fence, the left textbox will show corresponding SMS Header,
default as “In Alarm”.
Exit Geo-fence: alarm while the device exiting geo-fence, the left textbox will show corresponding SMS Header,
default as “Out Alarm”.
Map: click “In Map” to make and define geo-fence.
For complete software functions, please refer to Meitrack Manager User Guide.
6.5.3 Authorized Phone Number/GPRS Event
Select column 4 to set authorized alarm phone number, GPRS event and other functions. For complete software
functions, please refer to Meitrack Manager User Guide.
Copyright © 2014 Meitrack Group All rights reserved.
- 14 -

File Name:
MEITRACK MVT600 User Guide
Creator:
Cavana Cheung
Project:
MVT600
Creation Date:
Update Date:
2010-09-13
2013-09-16
Sub Project:
User Guide
Page:
- 15 - of 25
Revision:
V3.1
Confidential:
External Documentation
For more information about GPRS settings, please refer to MEITRACK SMS/GPRS Protocol.
6.5.4 GPRS Log
Column 5: GPS Log
Before using this function, please first setup GPRS log time interval( to set this option under column 1 ‘Device’ in
Meitrack Manager), The terminal device will automatically save the log in the storage chip when there exits GPS
signal. Recorded tracking & locating data can be exported under this column. No GPRS signal, no log.
Copyright © 2014 Meitrack Group All rights reserved.
- 15 -

File Name:
MEITRACK MVT600 User Guide
Creator:
Cavana Cheung
Project:
MVT600
Creation Date:
Update Date:
2010-09-13
2013-09-16
Sub Project:
User Guide
Page:
- 16 - of 25
Revision:
V3.1
Confidential:
External Documentation
7Installation
7.1 Install I/O Cable
The I/O cable is a 12-pin cable including power, analog input, digital temperature sensor input,
negative/positive input and output.
I/O
1
Power(+)
3
Input 3
5
Input 2
7
Output 1
9
Output 2
11
Output 3
2
GND(-)
4
Input 1 (-)
6
GND(-)
8
AD Input 1
10
Fuel Sensor
12
Digital
Temperature
Sensor
PIN Number Color Description
1 (Power) Red DC In (power source). Input voltage: 11V~36V. 12V suggested.
2 (GND) Black Ground
3 (IN3) White Digital Input3. Positive triggering, for detecting status of vehicle door or ACC.
4 (IN1) White Digital Input1. Negative triggering( Defaulted as SOS Panic Button)
5 (IN2) White Digital Input2. Negative triggering, for detecting status of vehicle door.
6 (GND) Black Ground. It can be used to connect with temperature/fuel sensor etc.
7 (OUT1) Yellow Output1. It can be used to connect with relay for engine immobilization.
Low voltage (0V) when effective and open drain when ineffective.
Output open drain sink voltage (ineffective): 45V max.
Output low voltage sink current (effective): 500mA max
8 (AD1) Blue 12 Bits Resolution Analog Input1. 0~6V DC Detection. It can be used to connect
with temperature/fuel sensor etc.
9 (OUT2) Yellow Output2. It can be used to connect with relay for engine immobilization.
Low voltage (0V) when effective and open drain when ineffective.
Output open drain sink voltage (ineffective): 45V max.
Output low voltage sink current (effective): 500mA max.
10(Fuel
Sensor
Blue 10 Bits Resolution Analog Inputs 2. 0~6V DC Detection. The AD cable with a white
plug is used to connect A53 fuel sensor.
Copyright © 2014 Meitrack Group All rights reserved.
- 16 -

File Name:
MEITRACK MVT600 User Guide
Creator:
Cavana Cheung
Project:
MVT600
Creation Date:
Update Date:
2010-09-13
2013-09-16
Sub Project:
User Guide
Page:
- 17 - of 25
Revision:
V3.1
Confidential:
External Documentation
Input )
11 (OUT3) Yellow Output3. It can be used to connect with relay for engine immobilization.
Low voltage (0V) when effective and open drain when ineffective.
Output open drain sink voltage (ineffective): 45V max.
Output low voltage sink current (effective): 500mA max.
12(Digital
Temperatur
e)
Blue TTL3.3V level, defaulted to be used to connect A52 digital temperature sensor
with A61 sensor box
Note: the current should be below DC/AC3.3V, otherwise, the device may be
damaged
Power/GND (PIN1/PIN2)
Connect GND (-Black) and Power (+Red) wires to the battery of vehicle.
7.1.2 Digital Input (PIN4/5, negative triggering)
7.1.3 Digital Input (PIN3, positive triggering)
Copyright © 2014 Meitrack Group All rights reserved.
- 17 -

File Name:
MEITRACK MVT600 User Guide
Creator:
Cavana Cheung
Project:
MVT600
Creation Date:
Update Date:
2010-09-13
2013-09-16
Sub Project:
User Guide
Page:
- 18 - of 25
Revision:
V3.1
Confidential:
External Documentation
7.1.4 Output
7.1.5r Input (PIN8/PIN10/PIN12)
7.1.5.1 Sensor Input Application 1– Inner battery voltage and external power voltage caculation formula
Inner battery voltage Caculating Formula: input voltage=(AD4*3.3*2)/4096
Inner battery percentage caculating formula: battery percentage = （（ AD4-2114）*100/492）100%
External power voltage caculating formula: external power input voltage = AD5/4096*3.3*16
Remark: AD4 & AD5 inside the device are defaulted to detect inner battery and external power voltage, not
indicated by the analogue input port. ( Please refer to MEITRACK_GPRS Protocol for more details)
Copyright © 2014 Meitrack Group All rights reserved.
- 18 -

File Name:
MEITRACK MVT600 User Guide
Creator:
Cavana Cheung
Project:
MVT600
Creation Date:
Update Date:
2010-09-13
2013-09-16
Sub Project:
User Guide
Page:
- 19 - of 25
Revision:
V3.1
Confidential:
External Documentation
7.1.5.2 Application 2 –Analog Fuel Detection (percentage of fuel)
Figure2
The fuel sensor we provide is A53 resistive voltage-output mode sensor, which needs to connect external power
to work. This sensor has three cables: the Power Cable (brown), GND(blue), and data output cable (yellow).
Power Voltage : DC 11V-36V, shared with terminal power. Data output voltage: 0-5V. The terminal AD2 cable has
a white plug to connect with the white plug of the fuel sensor.（Figure 2）. If connecting AD1 to fuel sensor, you
need to the white plug of the sensor and connect the three cables to the terminal as per figure 1.
Note: T1 defaults AD2 connect A53 fuel sensor and the program has used the formula to work out the value that
AD2 detected, that is, it uploads percentage result of fuel capacity in hexadecimal to the server and the server only
needs to resolve the result into decimal
For example: 0X2129(hexadecimal)=>High level 21 in decimal is 33, low level 29 in decimal is 41, then the
percentage of the residual oil detected is 33.41%
Connect AD1 with fuel sensor, thus, use a formula to calculate the result.
Formula: AD1*3.3*2/4096/5
Detect AD1 as 0x040D, then 0x040D=>1037
（ in decimal ） =>1037*3.3*2/4096/5=0.3341=33.41%.
AD analog input voltage calculating formula:
Voltage caculating formula:Input Voltage=(AD*3.3*2)/4096
0x0C9B=>3227(in decimal)=>(3227*3.3*2)/4096=5.1997V(voltage)
0x0D9D=>3845(in decimal)=>(3845*3.3*2)/4096=5.6154V(voltage)
Copyright © 2014 Meitrack Group All rights reserved.
- 19 -

File Name:
MEITRACK MVT600 User Guide
Creator:
Cavana Cheung
Project:
MVT600
Creation Date:
Update Date:
2010-09-13
2013-09-16
Sub Project:
User Guide
Page:
- 20 - of 25
Revision:
V3.1
Confidential:
External Documentation
7.1.5.3 Digital Temperature Sensor Input
T1 can connect with A53 Fuel Sensor directly as 7.1.5.2 mentioned above. It also can connect A52 Temperature
Sensor and A53 Fuel Sensor through the A61 sensor box, illustrated as the following three cases:
Case A:（A61+A52 Temperature Sensor）
T1 sen port（Digital Temperature Sensor Input Port）is connected to four temperature sensor probes with a A61
sensor box, to meausre four different temperature spots simultaneously.（such as car: car rear, carriage, car air
conditioner air-out, the engine, etc）, illustrated as the picture below:
Case B:（A61+A52 Temperature Sensor +A53 Fuel Sensor）
To connect four temperature sensor probes and one fuel sensor at the same time, just need to connect A53 Fuel
Sensor with the OUT port of A61 sensor box, illustrated as the picture below:
Copyright © 2014 Meitrack Group All rights reserved.
- 20 -