MAG BRD03 User manual

©2023 QG V2 BRD03 DualRay and LED Display
1
QUICK GUIDE
25 August 2023, V2
BRD03 DualRay and LED Display Traffic Detector
Technical Specification
Description
Parameter
Input Voltage
DC 12V, 250mA
Detection
Dual Lens for 3D Detection
Working Frequencies
24 - 24.5 Ghz
Modulation Mode
FMCW
Transmission Power
10 - 15 dBm
Detection Distance
1 - 6 meters, ± 0.2 meters
Working Temperature
-40°C - 85°C
IP Rating
IP67
Dimension
126mm(L) x 96mm(W) x 26mm(H)
Cable Colour
Description
Red
12V
Black
GND
Yellow
N.O SIGNAL
Blue
N.C SIGNAL
White
COM SIGNAL
Green
Not In Use
Installation and Wiring
Menu selection
Setting instruction:
1. Press and hold the “MENU” button for 3 seconds.
2. The LED Display show first menu which is “RANGE”.
3. Press the “MENU” button again to change to other
parameters
4. To set the value, press “SET/SAVE” button
5. After done, press and hold the “SET/SAVE” button until
the LED flash then let go the button, it will automatically
save and exits the menu.
6. Once complete, LED Display will back to Normal.
*(Note: After done any setting, it must be saved;
otherwise the setting will not change and the detector will
automatically exit the menu setting after 10 seconds)
RANGE Setting
SPEED Setting
MODE Setting
DELAY Setting

©2023 QG V2 BRD03 DualRay and LED Display
2
* Please note that, BRD03 is Plug and Play device, all the default setting initially set is base on normal installation.
** If there is changes environment or error at installation site please follow below instruction.
*Product performances is based on testing in a controlled environment. Your result may
vary due to several external and environment factors.
© COPYRIGHT 2023.This documentation served as a reference only. It is subject to change without further notice. All the diagrams and information
in this documentation may not be duplicated or modified in any form without the written approval from the management.
Menu
Parameter Setting
Remark
Default Value
- RANGE
Set maximum detection
distance
The range distance increase by 0.5meters
2.5 meters
- SPEED
Detection sensitivity
Time how long the sensitivity boost (only
on fence arm mode)
6 seconds
- DELAY
Set timer delay output
Timer for Barrier stay open after car is
passed by
0 seconds
- MODE
Working Mode
1: Straight Arm Mode / 2: Fence Arm
Mode
1.0
Working Mode
Sensitivity Low
Sensitivity Medium
Sensitivity High
Straight Arm Mode
1.L
1.0 (default)
1.H
Fence Mode
2.L
2.0
2.H
Function Parameter Setting and Description
Traffic Detector Parameter Setting
1) Detection distance
Setting instruction:
1. Press and hold the button to enter Menu “RANGE”
2. Press the “SET/SAVE” button to set the distance.
3. Each time press “SET/SAVE” it will increase by 0.5 meter.
4. After select distance. Press and hold the “SET/SAVE”
button, LED display will start blinking
5. After setting is done only LED display will back to normal
*Note: Make sure detection range is 0.5 meter less then
the actual arm length
Setting instruction:
1. Press and hold the “MENU” button to enter Menu
2. Press “MENU” button until “MODE” Menu
3. Press the “SET/SAVE” button to set the mode.
4. After select mode. Press and hold the “SET/SAVE”
button, LED display will start blinking
5. After setting is done only LED display will back to normal
2) Working Mode
*Note: Working mode is important and it depends on
barrier arm type. Its advisable to set to 1.0 (Default) to
make BRD03 working at optimal performance.
Low Sensitivity is used for distinguish.
SPECIAL NOTE
* Make sure to use low noise power supply.
*Only install the BRD03 on flat surface and
do not install it in front uneven road surface.
SCAN HERE:
*For fence arm barrier
setting, please refer to full
installation manual.
*For full installation manual
and setting, please scan
the QR Code beside.