Magellan Outdoors Pro Explore VPN 172583 User manual

Note: Before beginning assembly of product, make sure all
parts are present. Compare parts with package content list
and hardware contents. If any part is missing or damaged do
not attempt to assemble the unit. Contact customer service
for replacement parts.
Table of Contents
Warnings and Care Instructions........................................................2
Inflation..............................................................................................3
Deflation............................................................................................4
Warranty Information.........................................................................5
Please keep this instruction manual for future reference
Customer Service: [phone]
7:00 am to 10:00 pm CST (daily)
Live Chat at: www.academy.com
Email: [e-mail]
Assembly Instructions
& User’s Manual
VPN 172583
Magellan Outdoors Pro Explore
Deluxe Self Inflating Foam Sleeping Pad
1

Warnings and Care Instructions
Do NOT expose to open flame.
Store pad in a cool dry place.
Not suitable for water activity, ie. Swimming pools or salt water. This is
NOT a water recreation product.
Use soapy water and rinse with clean water, then dry fully before storage.
Washing & Cleaning
Prior to storage, please ensure that the pad is completely dry. Failure to
do so can result in excessive dampness leading to mildew, which can
damage the fabric. We recommend that the pad be stored extended and
fully inflated with the valve open. This retains the foam's memory, allowing
quick inflation when next used. It also maintains the pad's integrity by
allowing trapped moisture to escape.
Storage
Do NOT leave the pad inflated with closed valves inside tent on hot days.
Air inside the pad will expand when the temperature increase and the high
pressure may cause the fabric to delaminate from the foam. Open the
valve when the mat is not in use.
Caution
Inflation
1.Take out the pad from the carry bag. 3.Wait for 6-10 minutes for pad to
self-inflate.
4.(Optional) If the hardness of pad is not
enough, inflate the pad with carry bag.
Inflate pad to your preference.
5.Close the valve cap clockwise until it's
a lttle tight. Do not over tighten the valve
cap.
Enjoy your sleeping pad!
2.Turn valve cap counter-clockwise to
open it. Turn the Flip Valve to "quick
self-inflate" position for valves (note:
one valve only for single pad).
2.1
2.2 5.1
4.1 4.2
4.3 4.4
valve
Part List
A Self-inflating sleeping PAD
B Compression Straps
C Carry Bag with valve(can be used as a pump)
D Self-Adhesive Fabric Patches
2 3

Warranty Information
This product has been manufactured under the highest standards
of quality and workmanship. We warrant to the original consumer
purchaser that all aspects of this product will be free of defects in
material and workmanship for one year from the date of purchase.
A replacement for any defective part will be supplied free of charge
for installation by the consumer. Defects or damage caused by the
use of other than genuine parts are not covered by this warranty.
This warranty shall be effective from the date of purchase as shown
in the purchaser receipt.
This warranty is valid for the original consumer purchaser only and
excludes industrial, commercial or business use of the product,
product damage due to shipment or failure which results from alter-
ation, product abuse, or product misuse, whether performed by a
contractor , service company , or consumer. We will not be respon-
sible for labor charges and/or damage incurred in installation, repair
or replacement nor for incidental or consequential damage.
Deflation
1.Turn and open the valve cap,reverse
the Flip Valve to“Deflate" position.
4.Lay the compression straps on the
ground as shown below.
5.Roll the pad compact and put it on the
compression straps, assemble the
handle buckle one by one. You may
adjust the straps length to make the
compression straps tight. You can hand
carry the pad with the straps handle
without carry bag if needed.
6.Insert the bound pad into carry bag. Fold
the opening of carry bag and assemble the
buckle.
3.Close the valve cap clockwise until it's
a little tight when the inside air is remove
completely. Do not over-tighten the valve
cap.
2.Roll from the opposite side of the valve
to allow the air to escape quickly. You
may need to repeat rolling 2-3 times to
remove the inside air completely.
2.1 2.2
2.3 2.4
3.1
5.1 5.2
6.2
6.1
6.3
Deate
1.1 1.2 1.3
4 5