Magic Bullet MBR-0307 User manual

user
guide.

1 2
NEVER leave spoons or other
foreign objects in the cup before
blending. Failure to do so will
result in damage to the cup and/
or possible personal injury.
Never leave the magic bullet®
unattended while it is in use.
Close supervision is necessary
when any appliance is used by or
near children.
Never blend carbonated
ingredients or liquids. Built-up
pressure from released gases can
cause the blade and cup to
separate, possibly resulting in
personal injury.
Friction from the rotating blade will
cause ingredients to heat and
generate internal pressure in the
sealed cup. Do not continuously
operate for more than one minute. If
the cup is warm to touch, allow to
cool before carefully opening
pointed away from your body.
Never permit any blended mixture
to sit inside a sealed vessel without
first releasing internal pressure. If
storing blended ingredients,
remove the blade from the cup and
replace with the flip top lid.
Never store the extractor blade on
the power base without a cup or
vessel attached. Failure to do so may
result in personal injury if the unit is
accidently turned on.
important safeguards.
Warning! To avoid the risk of serious injury, carefully read all
instructions before operating your magic bullet®. When using any
electrical appliance, basic safety precautions should always be
observed, including the following important information.
Save These Instructions!
FOR HOUSEHOLD USE ONLY
personal safety:
NEVER PUT HOT LIQUIDS IN ANY OF
THE SEALED BLENDING CUPS
BEFORE BLENDING.
Start with cold or room temperature
ingredients. Heated ingredients
can create internal pressure in a
sealed blending cup, which may
erupt on opening and cause
thermal injury.
!

3 4
warning:
If you are taking any
medication, especially
cholesterol-lowering
medication, blood thinners,
blood pressure drugs,
tranquilizers, or antidepres-
sants, please check with your
physician before consuming
any magic bullet®recipes.
The following list of seeds
and pips contain chemicals
that release cyanide into the
body when ingested. Do not
use: apple seeds, apricot
seeds, cherry pips, plum
pips, and peach pips in your
magic bullet®.
Switch o the appliance and
disconnect from power supply
before changing accessories or
handling moving parts. At all times,
avoid contact with moving parts.
Keep hands and utensils away
from the extractor blade.
TO REDUCE THE RISK OF
PERSONAL INJURY OR LEAKAGE,
make sure the extractor blade is
securely twisted (hand-tightened)
onto the magic bullet® blending cup
before placing it on the motor base.
Check to make sure the easy-twist
extractor blade is aligned properly
before placing it on the motor base
and operating your magic bullet® .
The cup and blade are consumable
components, over time, if the unit
starts to get louder or make unusual
noise or vibration, it indicates that
these consumable parts may need
replacing. The continued use of
worn parts may result in part failure
and/or personal injury.
This appliance is not intended for
use by persons (including children)
with reduced physical, sensory or
mental capabilities, or lack of
experience and knowledge, unless
they have been given supervision
or instruction concerning use of the
appliance by a person responsible
for their safety.
VERY IMPORTANT: If there is a
liquid spill, immediately disconnect
the unit from the power source. If
the spill is external only, clean with
a warm soapy cloth and allow unit
to dry completely before operating.
If the spill has leaked in to the
internal components of the power
base, cease use immediately. Unit
must be checked by a Qualified
Electrician and certified as
electrically safe before using
again. Failure to do so will result in
a possible electric shock and/or
personal injury.
To avoid risk of electric shock,
never immerse the cord, plug, or
power base of blender in water or
other liquids.

5 6
cleaning. Exposure to hot water
can cause damage to the seal in
the outer rim of the attachment.
Always inspect your blades before
each use.
Use of adapters and converters is
considered an unauthorized
modification of the product and as
such will void the warranty.
The use of attachments not
recommended or not sold by the
manufacturer will void warranty
and may cause fire, electric shock,
or injury.
Use of this product in locations
with dierent electrical
specifications may result in
damage to the product.
TO AVOID LEAKAGE, DO NOT
OVERFILL THE CUP. Your magic
bullet®cups are also marked with a
MAX line. When filling the cup or
pitcher, make sure your ingredients
do not exceed their respective
MAX lines.
The magic bullet®is not intended
for use in microwave ovens. Do not
place the magic bullet®cups,
power base or any accessories in a
microwave as this may result in
damage to the appliance.
Extractor blades are
sharp! Handle carefully.
Do not remove the seal from your
blade attachment. The seal is not
designed to be removed. If seal is
removed, cease use immediately
and purchase a replacement.
If, over time, the extractor blade
becomes loose or damaged, you
may order a new extractor blade at:
www.bulletbrands.com.au /
www.bulletbrands.co.nz or contact
customer service.
We recommend replacing your
extractor blade every 6 months
(depending on use) or as needed
for optimal performance.
Blade attachments should not be
placed in the dishwasher for
product safety:
To prevent the overheating of the
ingredients being blended, never
allow the unit to run continuously for
more than 1 minute.
If the motor stops for any reason,
unplug the power base and let it
cool for at least 15 minutes.
If the magic bullet®malfunctions or
is dropped, or damaged in any
manner, discontinue use and
contact Customer Service for
further assistance.
NEVER USE THE MAGIC BULLET®
WITHOUT ADDING LIQUID OR WHEN
THE CUP IS EMPTY, AS DOING SO
MAY DAMAGE THE BLADE

7 8
Unplug the magic bullet®when it is
not in use. Make sure the power base
is unplugged before assembling,
disassembling, adding additional
parts, or cleaning.
Do not use magic bullet®outdoors. If
exposed to inclement weather
elements such as rain or other wet
conditions, discontinue use.
Unplug the magic bullet®when it is
not in use. Make sure the power base
is unplugged before assembling,
disassembling, adding additional parts,
or cleaning.
Periodically inspect your magic
bullet®cups for damage or wear that
may impair proper function.
Discontinue use and replace
components if you detect cracking,
caution:
In order to avoid a hazard due to
inadvertent resetting of the
thermal cut-out, this appliance
must not be connected to an
external switching device, such as
a timer, or connected to a circuit
that is regularly switched on and
o by the utility.
Periodically inspect cord and plug
for damage. Do not operate any
appliance with a damaged cord or
plug. If damaged, it must be
replaced by the manufacturer, its
service agent, or similarly qualified
persons in order to avoid a hazard.
Do not allow the cord to hang over
the side of the counter or table. Do
not allow the cord to touch hot
surfaces, including stove.
The cyclonic action of your magic
bullet®requires the use of liquids to
make smoothies and other nutritious
beverages. The magic bullet®is not
intended to be used as an ice crusher
and not intended to be used without
liquids. To make a delicious cold
smoothie, we suggest that you use
frozen fruit and chilled liquids.
Alternatively, you may add crushed
ice, up to 25% of the total cup volume,
with water or other liquid filled up to
the “MAX” line. Do not crush ice or
other hard items without liquid, as
such prolonged use over time may
dull or damage the blades.
warning:
ventilation caution
Always operate the magic bullet®
on a level surface, leaving
unobstructed space beneath and
around the power base to permit
proper air circulation. Slots and
openings on the bottom of the
product are provided for
ventilation to ensure reliable
motor operation and to prevent
over-heating.
To prevent fire hazard, power
base openings should be free of
dust or lint and never obstructed
with flammable materials such as
newspapers, tablecloths, napkins,
dishtowels, or place mats.

910
crazing or cloudiness/discolouration,
or other damage to the plastic cups,
or tabs (on the side of the cup). You
may purchase new cups and cross
blades at www.bulletbrands.com.au,
www.bulletbrands.co.nz or contact
Customer Service:
Australian Consumers:
1300 285 538
New Zealand Consumers:
0800 232 633
Save these
instructions!
FOR HOUSEHOLD
USE ONLY
!
what’s included.
stainless steel
cross blade
motor base tall cup
Product configurations may vary.
To see our full list of magic bullet®accessories please visit:
www.bulletbrands.com.au /www.bulletbrands.co.nz

11 12
Using the magic bullet® .
3Twist on the Cross Blade until
the blade and Cup are tightly
sealed.
2Load the ingredients into
the Cup (do not exceed the
MA X line).
Using the magic bullet®is as easy as 1, 2, 3:
1Before first use, review all warning and caution statements in the
Important Safeguards section (pages 1–8). Clean Blending Cups and
Cross Blade with hot, soapy water before use.
“Lock-on” mode:
For hands-free operation, press
down and gently turn the Cup
clockwise until the tabs lock under
the lip of the Motor Base. Once you
are in lock-on mode, the motor will
run continually (do not run for
longer than a minute!). To stop
blending, simply twist the Cup
counter-clockwise to release.
4Line up the tabs on the Cup
and with the tabs on the Motor
Base. Press the Cup down
onto the base to turn on the
machine.
Here’s how it works: The
magic bullet®will blend for
as long as you press the Cup
down onto the Motor Base. To
stop blending, simply release
pressure on the Cup.

13 14
caution:
Before using the Cross Blade, check
the gasket to make sure it is not
damaged and it is completely seated in
the Cross Blade Unit before each use.
Never put your hands or utensils near
the moving Cross Blade and never use
your hands or utensils to press the
activator buttons down while the
Motor Base is plugged in.
If the Cross Blade stops spinning while
in lock on mode, immediately unplug
the magic bullet® .Hard ingredients like
carrots or celery can get stuck in the
Cross Blade and stop it from turning. If
this happens, unplug the magic bullet®
right away. Remove the blade/cup
assembly from the Motor Base, and
give ingredients a good shake to
unblock the Cross Blade. If the Cross
Blade still remains obstructed, twist
the Cross Blade attachment off of the
Cup and carefully spin the metal
blades using a utensil (not your fingers)
to release the blockage. Reattach the
Cross Blade to the Cup, plug in the
magic bullet®and try again. It should
spin normally.
Never run the magic bullet®for more
than one minute at a time, as it can
cause permanent damage to the
motor. If the motor stops working,
unplug the Motor Base and let it cool
for a few hours before attempting to
use it again. Your magic bullet®has an
internal thermal breaker that shuts the
unit off when it overheats. Letting the
thermal breaker cool down should
allow it to reset.
care & maintenance.
Cleaning the magic bullet®is easy. Simply place any of the parts (except
for the Motor Base and Cross Blade) on the top rack of the dishwasher or
hand wash with warm, soapy water and rinse.
step 1: Always power off and
unplug the Motor Base from
the outlet when it is left
unattended, before assembling,
disassembling, changing
accessories or approaching parts
that move in use or when cleaning.
Do not attempt to handle the
appliance until all parts have
stopped moving!
step 2: Make sure the Blending
Cup/Cross Blade is not attached to
the Motor Base.
step 3: Clean the individual
components (Motor Base, Cross
Blade, magic bullet®Blending Cups).
motor base:
• To avoid risk of injury, never use
your hands or utensils to clean
the White Actuator Tabs while
the magic bullet®is plugged in.
• Never submerge the Motor Base
in water or put in the dishwasher.
• Do not remove the rubber or plastic
liners inside the Motor Base.

15 16
• Use a sponge or dish cloth
dampened with warm soapy
water to wipe down the inside
and outside of the Motor Base
until clean.
• Pay particular attention to the
actuator tabs on the inside of the
Motor Base to loosen any stuck
or sticky debris from drips and
spills. If necessary you may use a
small brush to scrub the area to
ensure it is kept clean.
cross blade:
DO NOT REMOVE THE GASKET AS
THIS MAY PERMANENTLY
DAMAGE THE CROSS BLADE AND
CAUSE LEAKAGE
• If after washing as indicated
additional disinfecting is desired,
you may rinse with a 10%
vinegar/water solution. If, over
time, the gasket becomes loose
or damaged, you may order a
new Cross Blade at:
www.bulletbrands.com.au or
www.bulletbrands.co.nz.
• Dry the Cross Blade completely.
It is helpful to turn the blade on
its side in your dish drainer to
ensure both sides of the Cross
Blade are completely dried.
• We recommend replacing your
magic bullet®Cross Blade every
6 months or as needed for
optimal performance. To order
replacement Cross Blades,
simply visit:
www.bulletbrands.com.au or
www.bulletbrands.co.nz.
blending cups
cups, lids and lip rings:
• These items are all Top Rack
dishwasher safe. We recommend
rinsing them and giving them a
quick brush with a dish brush to
remove any dried debris before
washing them in the dishwasher.
Never use the sanitize cycle to
wash the blending cups as this
may warp the plastic.
• Regularly check the tabs (3) on
the sides of the Cups for damage
(cracking, crazing, breakage or
rounding). If the tabs are
damaged, discontinue use and
replace immediately to prevent
possible personal injury.
replacement
parts.
To order additional parts and
accessories, please visit our
website at:
www.bulletbrands.com.au or
www.bulletbrands.co.nz.
storing leftovers in the
magic bullet®cups
The magic bullet®includes Stay Fresh
Resealable Lids that twist directly
onto your magic bullet®Cups,
allowing you to prep food ahead of
time, keep leftovers fresh, or take
your meal on the go without dirtying
an extra storage container.

17 18
ONE (1) YEAR
LIMITED REPLACEMENT WARRANTY STATEMENT
If your product becomes defective due to faulty material or workmanship within a period of 1 year from
the date of purchase, we warrant to do the following:
• For New Zealand Consumers: We will replace the product with a new product, free of charge, or
repair the product at our cost, at our discretion.
• For Australian Consumers: Our goods come with guarantees that cannot be excluded under the
Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for
compensation for any other reasonably foreseeable loss or damage. You are also entitled to have
the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does
not amount to a major failure.
Your warranty is subject to the following conditions:
• DO NOT operate the appliance with a damaged plug or cord, or if the unit has been dropped,
damaged or dropped in water. To avoid the risk of electric shock, do not disassemble or attempt to
repair the appliance on your own. If the supply cord is damaged, it must be replaced by a qualified
electrician in order to avoid a hazard. Incorrect re-assembly or repair can cause a risk of electric
shock or injury to persons when the appliance is used.
• The item has not been misused, abused, neglected, altered, modified or repaired by anyone.
• The item has been subjected to fair wear and tear.
• The item has not been used for trade, professional or hire purposes.
• The item has not sustained damage through foreign objects, substances or accident.
Your warranty does not cover;
• Components that are subject to natural wear and tear caused by normal use in accordance with
operating instructions.
• Unauthorised/improper maintenance/handling or overload is excluded from this warranty.
• For guarantee claims, you will need to submit a proof of purchase in the form of a valid receipt that
displays date and place of purchase.
This warranty does not replace but is in addition to your statutory rights.
This warranty does not apply to accessories supplied with the item.
This warranty applies only to the original purchaser and may not be transferred.
Replacement items will be covered by the limited warranty for the balance of the warranty period from
the date of the original purchase.
Please note:
Only the defective product or parts returned to place of purchase will be replaced under this warranty.
NEW ZEALAND
PO Box 100-707
NSMC
Auckland 0745
0800 232633
www.bulletbrands.co.nz
AUSTRALIA
PO Box 574
South Morang
Victoria 3752
1300 285538
www.bulletbrands.com.au