Magic Home CS-W579S00013 User manual

1
Installation
Hardware List
Hardware List
Seat
1
Backrest
1
Right armrest
1
8x25mm screws
16
Nuts、
Washers、long screws
4
Legs
5
Support rods
2
Iron sheets
2
1
2
Install the support rods as shown in picture 1
Backrest
8x25mm screw
Insert the backrest into the seat
cushion, notice the short lock
buckles facing forward, and then
fasten the lock buckles to the ring of
the seat cushion according to the
diagram. (If the rope is not long
enough, don’t worry, this is not a
quality problem, it’s for the solidness
after the installation of the lock
buckles. When this happens you
need to press the backrest and the
seat cushion down, the lock can be
easily buckled)

2
3 Turn over the seat, install the feet and fasten support rods.
4 Install the armrests. Please refer to step 2
1
1-4 steps: insert the long screws into the
backrest support rod, about 7-8 mm deep,
and let the rest of the screw go through the
iron sheet, then apply 8x25mm screws to fix
4 predrilled holes about half way, when all
the screws are in place with the holes,
tighten them completely.
Tip: If holes and screws do not match, try to
adjust them adjustable space has been
reserved.
3
2
4
Right armrest

1
Installation
Hardware List
Hardware List
Seat
1
Backrest
1
Left armrest
1
8x25mm screws
16
Nuts、
Washers、long screws
4
Legs
5
Support rods
2
Iron sheets
2
1
2
Install the support rods as shown in picture 1
Backrest
8x25mm screw
Insert the backrest into the seat
cushion, notice the short lock
buckles facing forward, and then
fasten the lock buckles to the ring of
the seat cushion according to the
diagram. (If the rope is not long
enough, don’t worry, this is not a
quality problem, it’s for the solidness
after the installation of the lock
buckles. When this happens you
need to press the backrest and the
seat cushion down, the lock can be
easily buckled)

2
3 Turn over the seat, install the feet and fasten support rods.
4 Install the armrests. Please refer to step 2
1
1-4 steps: insert the long screws into the
backrest support rod, about 7-8 mm deep,
and let the rest of the screw go through the
iron sheet, then apply 8x25mm screws to fix
4 predrilled holes about half way, when all
the screws are in place with the holes,
tighten them completely.
Tip: If holes and screws do not match, try to
adjust them adjustable space has been
reserved.
3
2
4
Left armrest

1
Installation
Hardware List
Hardware List
Seat
1
Backrest
1
Ottoman
1
8x25mm screws
16
Nuts、
Washers、long screws
4
Legs
10
Support rods
2
Iron sheets
2
1
2
Install the support rods as shown in picture 1
Backrest
8x25mm screw
Insert the backrest into the seat
cushion, notice the short lock
buckles facing forward, and then
fasten the lock buckles to the ring of
the seat cushion according to the
diagram. If the rope is not long
enough, don’t worry, this is not a
quality problem, it’s for the solidness
after the installation of the lock
buckles. When this happens you
need to press the backrest and the
seat cushion down, the lock can be
easily buckled)

2
3 Turn over the seat, install the feet and fasten support rods.
4 Finished.
1
1-4 steps: insert the long screws into the
backrest support rod, about 7-8 mm deep,
and let the rest of the screw go through the
iron sheet, then apply 8x25mm screws to fix
4 predrilled holes about half way, when all
the screws are in place with the holes,
tighten them completely.
Tip: If holes and screws do not match, try to
adjust them adjustable space has been
reserved.
3
2
4