Magnadyne M9900-SWR3 User manual

M9900-SWR3_IMUM 5/19/05 3:54 PM Page 1
1. Attach the remote holder base to the inside
edge of the steering wheel using the strap
supplied as shown in Figure 1. Make certain
that the arrow engraved into the remote hold-
er base is facing the driver. Secure one end of
the strap to the outer edge of the remote
holder base as shown in Figure 1. Pull the
strap snug around the steering wheel and
secure the strap to the cleats on the holder
base. Some stretching of the strap will be
required but do not over-stretch the strap.
3. Attach the remote holder cover loosely to the
holder base using the screws supplied as
shown in Figure 3. Adjust/rotate the remote
holder assembly to the desired position and
tighten the screws.
4. Attach the Remote Control unit to the Holder
as shown in Figure 4 until a "click" sound is
heard. To remove the Remote Control unit
from the Holder, press the Ribbed Switch
toward the steering wheel, then slide the
Remote Control off the Holder.
WARNINGS
• Do not install this Steering Wheel Remote in
a location where it prevents the proper
operation of safety devices such as air bags.
• Do not install this unit in a location where it
prevents the proper operation of the steering
wheel or gearshift lever.
• Do not install this Steering Wheel Remote in
a location that may obstruct the driver’s view.
• Do not install this unit to the outer edge of
the steering wheel, it may interfere with
driver’s ability to steer the vehicle which
could result in a traffic accident. Always
attach this unit to the inside edge of the
steering wheel as shown in Figure 5.
• Mount this unit securely to the steering
wheel. If this unit is loose, it may interfere
with driver’s ability to properly steer the
vehicle.
• Installation of this unit requires special skills
and experience and should be entrusted to a
trained technician.
• Install this unit using only the parts supplied.
If other parts are used the unit may be
damaged or could dismount itself, which
could result in a traffic accident.
• Only install this unit as illustrated in this
manual.
Steering Wheel Remote
Installation Guide for the M9900CDS Receiver
Model: M9900-SWR3
Figure 1
Strap
Remote
Holder
Steering Wheel
Arrow
Figure 3
Remote Holder
Cover
Figure 2
Figure 4
Ribbed
Switch
Incorrect Location
Correct Locations
Figure 5
2. Cut the extra portion of the strap near the
center of the remote holder as shown in
Figure 2.

PLAY/PAUSE
W.B. MODE
TRACK
SEEK
LEVEL
+
LEVEL
-
UP
DN
10
2
14
17
3
5
M9900-SWR3
4
© Copyright 2005 Magnadyne Corporation
M9900-SWR3-IMUM 5-19-05 Rev. C
Steering Wheel Remote Functions and Controls for the M9900CDS Receiver
4. Multi-Function Button:
Radio Mode: Push to recall preset radio
station #1.
CD Mode: Push to enter CD track memory
mode (see M9900CDS Manual for more
information, pages 6-7).
CD Changer Mode: Push to change to a
lower disc in the CD changer.
Sirius Satellite Radio Mode: Push to recall
preset radio station #1.
5. Multi-Function Button #2:
Radio Mode: Push to recall preset radio
station #2.
CD Mode: Push to play programmed CD
tracks (see M9900CDS Manual for more
information, pages 6-7).
CD Changer Mode: Push to change to a high-
er disc in the CD changer.
Sirius Satellite Radio Mode: Push and
release when recalling preset radio station #2.
Installing a New Battery
Note: Replace with battery number CR2032 only.
1. While pressing the button on the steering wheel
mount, slide the remote control forward.
2. Slide battery cover off the remote control.
3. Remove the battery from the remote control.
4. Properly insert a new battery into remote.
Note: The positive side on the battery is
facing up.
5. Replace cover and slide the remote back
onto the steering wheel mount until it clicks
into place.
2. Volume Controls:
Press the "Level +" button to increase the
volume level.
Press the "Level –" button to decrease the
volume level.
3. Tune/Seek Buttons:
Radio Mode:
Manual Tuning:
Push one of the SEEK but-
tons and hold until “MANUAL” appears in
the display then release button. Push the
SEEK buttons again left or right until the
desired radio station appears in the display.
Seek Tuning: Push one of the
SEEK buttons
and release. The tuner will scan to the next
strong station and stop.
Sirius Mode: Push either SEEK button to
change to the next the Sirius radio station
.
C
D and CD Changer Mode: Push either
SEEK button to change the CD track on the
CD
that is playing.
10. Weather Band Radio Button: Push to
instantly access the weather band radio.
Push mode to return to previous source.
14. Mute Button (CD Play/Pause) Button:
Radio and Sirius Satellite Radio Mode:
Push to mute volume level. Push again to
restore volume.
CD and CD Changer Mode: Push to pause
disc play, push again to resume play.
17. Mode Button: Push to change the play
source: Radio, Sirius Satellite Radio, CD,
CD Changer or Auxiliary Sources.
M9900-SWR3_IMUM 5/19/05 3:54 PM Page 2
Model: M9900-SWR3
CAT/DISC