Magnavox MM440 User manual

FCC COMPLIANCE STATEMENT:
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications to this unit not expressly approved by the part
responsible for compliance could void the user’s authority to operate the equipment.
FCC Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirement.
The device can be used in mobile/ fixed (min 20cm) exposure condition without restriction.

6
LOCATION OF CONTR0LS
MAN UNIT:
Front:
1. Remote Receiver
2. LED Display
3. VOLUME Control Knob
4. (（Disc Tray Open-Close)/(Standby) Button
5. I◄◄ (Skip backward/Radio program down) Button
6. ►►I (Skip forward/Radio program up) Button
7. AUX (In) Jack
8. CD Disc Tray
9. ►II/PP (Play-Pause/Radio Program Preset) Button
10. ■/ (Stop/Decorative Lights On-Off) Button
11. MODE Button
12. USB Port (For music playback)

7
Rear:
1. FM ANT (Antenna)
2. POWER Switch
3. DC 15V (In) Jack
4. Speaker R (right) Clips
5. Speaker L (left) Clips

8
REMOTE CONTROL:
1. (Standby) Button
2. Numeric Buttons
3. PROG (Program) Button
4. ◄◄ (Fast rewind/Radio tuning down) Button
5. I◄◄ (Skip backward/Radio program down) Button
6. REP (Repeat) Button
7. ►II/PP (Play-Pause/Radio Program Preset) Button
8. (Disc Tray Open/Close) Button
9. 5+ Button
10. MODE Button
11. ■(Stop) Button
12. (Mute) Button
13. ►► (Fast forward/Radio tuning up) Button
14. VOL + (Volume Up ) Button
15. ►►I (Skip forward/Radio program up) Button
16. VOL - (Volume Down ) Button
17. EQ (Equalizer) Button
18. Button Cell Holder

9
CONNECTION:
Connect the Speaker Connection Wires from Speaker Boxes to Speaker Out Clips on
the rear of unit as illustrated below:

10
POWER SOURCE:
Main unit:
Connect the small plug from the supplied AC/DC Adaptor to the DC 15V (In) Jack on
the rear of unit then plug the AC/DC Adaptor to a AC wall outlet having AC 100-240V~;
50/60Hz as illustrated below:
NOTES:
If you will not use the unit for an extended period of time, unplug the AC/DC
Adaptor from wall outlet.
The AC/DC Adaptor is intended to be correctly orientated in a vertical or floor
mount position.

11
Remote Control:
First time use:
Remove and discard the insulation film as illustrated below:
Replacing the button cell when it is drained as follows:
Push and slide out the button cell holder as illustrated below.
Replace the button cell with new CR2025 button cell with the polarity
markings on the rear of the Remote Control.
Close the button cell holder.
Battery precautions:
Follow these Battery Precaution when using a battery in this device:
1. Use only the size and type of battery specified.
2. Be sure to follow the correct polarity when installing the battery as indicated in the
battery compartment. A reversed battery may cause damage to the device.
3. Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or
old batteries with fresh ones.
4. If the batteries in the device are consumed or the device is not to be used for a
long period of time, remove the batteries to prevent damage or injury from
possible battery leakage.
5. Do not try to recharge the battery not intended to be recharged; it can overheat
and rupture. (Follow battery manufacturer’s instructions.)

12
6. Do not dispose of battery in fire. Battery may explode or leak.
7. Clean the battery contacts and also those of the device prior to battery
installation.
8. This product contains a coin/button cell battery. If the coin/button cell
battery is swallowed, it can cause severe internal burn in just 2 hours and can lead
to death.
Keep new and used batteries away from children. If the battery compartment does
not close securely, stop using the product and keep it away from children.
If you think batteries might have been swallowed or placed inside any part of the
body, seek immediate medical attention.
EFFECTIVE DISTANCE OF REMOTE CONTROL
When there is an obstacle between the unit and the transmitter, the transmitter
may not operate.
When direct sunlight, an incandescent lamp, fluorescent lamp or any other
strong shines on the remote control of the unit, the remote operation may be
unstable.

13
OPERATION:
GENERAL OPERATION:
1. Connect the Speaker Boxes to the unit as previously instructed.
2. Connect the unit to AC power as previously instructed.
3. Slide the POWER Switch to ON position to power on the unit to standby mode. "O"
will appear on the display.
4. Press and hold the (Standby) Button on the unit or press the button on
the Remote Control to power on the unit from standby mode.
5. Press the MODE Button on the Unit or Remote Control repeatedly to switch to
desired playback mode. The correspondent indicator will appear (or illuminate)
on the display with your selection (see list below):
Playback Mode: Indicators:
CD “Cd”will appear on the display
USB “USb”will appear on display & the
indicator“USb”will illuminate
AUX (Aux/Line in) “AUH”will appear on the display &
the indicator “AUH”will illuminate
BT (Bluetooth) “bt”will appear on the display & the
indicator“bt”will illuminate
Radio FM Band “rAdI0”will appear on the display a
few seconds, then radio frequency
“XX.XX” or “XXX.XX” will appear on the
display
6. During playback:
Turn the VOLUME Control Knob on the unit or press the VOL (Volume) +/-
buttons on the Remote Control to adjust volume level as desired.
Press the (Mute) Button on the Remote Control to mute the sound, press
again to turn the sound back on.
Press the EQ (Equalizer) Button on the Remote Control to activate and set
the equalizer effect as desired (see list below):
Showing on display: Equalizer effects:
OFF Turn off the equalizer effect
ROC Rock
JA22 Jazz
POP Pop
CLASS Classic

14
7. When finished listening, press and hold the (Standby) Button on the unit or
press the button on the Remote Control to turn the unit to Standby Mode.
NB: If you will not use the unit for an extended period of time, slide the POWER
Switch to OFF position to power off the unit then unplug the AC/DC Adaptor from
AC wall outlet.
CD:
CD Playback:
1. Power on the unit as previously instructed.
2. Press the MODE Button on the Unit or Remote Control repeatedly until “Cd” appear
on the display.
3. Press the (Disc Tray Open/Close) Button on the unit or Remote Control to
open CD tray.
4. Place a CD disc on the center of tray, with the printed side face up.
5. Press the (Disc Tray Open/Close) Button on the unit or Remote Control to close
it, play will automatically start after a few seconds.
6. During playback:
Press the ►II/PP Button on the unit or Remote Control to pause, press again
to resume normal playback.
Press the I◄◄ or ►►I buttons on the unit or Remote Control repeatedly to
skip tracks.
Press the ◄◄ or ►► buttons on the Remote Control to fast searching the
specific section then press the ►II/PP Button to resume normal playback.
7. To stop, press the ■(Stop) Button on the unit or Remote Control.
Repeat Playback:
1. During playback, press the REP Button on the Remote Control once. The indicator
" " will appear on the display. The current track will playback repeatedly.
2. During playback, press the REP Button twice. The indicator "ALL "
will appear on the display. All the tracks on the current disc will be played back
repeatedly.
3. To cancel the repeat function, press the REP Button repeatedly until the repeat
indicator " " disappears on the display.
Programmed Playback:
Up to 20 tracks can be programmed playback as follows:
1. In CD stop playing mode, press the PROG Button on the Remote Control. “P 01”
will appear on the display. Indicator “PROG” will appear on the display and blink.

15
2. Select the first specific track to be programmed by pressing the I◄◄ or ►►I
buttons on the unit or Remote Control repeatedly.
3. Press the PROG Button again to store the selected track into the memory.
4. Repeat steps 2 and 3 until all the specific tracks stored into the memory.
5. Press the ►II/PP Button on the unit or Remote Control to start program
playback.
6. To stop playback, press the ■Button on the unit or Remote Control. Press the
►II/PP Button to start program playback again.
7. To stop and cancel the program, press the ■Button on the unit or Remote
Control repeatedly until indicator “PROG” disappears on the display.
BT:
BT (Bluetooth) pairing:
First time use or re-pairing the unit to a new BT Device, pair as follows:
1. Power on the unit as previously instructed.
2. Press the MODE Button on the Unit or Remote Control repeatedly until indicator
“bt” appears on the display and blinks to enter to BT mode.
3. Power on the external BT Device and enter to BT searching mode. Start pairing
following the on screen instructions from the external BT Device. When paired,
the indicator “bt” on the display will stop blinking.
4. If pairing is complete you may now play music with your external BT Device.
5. During playback:
Press the ►II/PP Button on the unit or Remote Control to pause, press again
to resume normal playback.
Press the I◄◄ or ►►I buttons on the unit or Remote Control repeatedly to
skip tracks.
Notes:
When the external BT Device has searched the unit, our model number “MM440”
will appear on the display of external BT Device.
If while pairing you are asked for a code please try "0000" or "1234".
Normal operation after pairing:
1. Power on the external BT Device and enter to BT playback mode.
2. Power on the unit and enter to BT mode as previously instructed. Indicator “bt”
will appear on the display and blink.

16
3. Wait a few seconds until the unit is automatically paired to the external BT Device.
The indicator “bt” on the display will stop blinking.
4. After pairing is complete you may now play music with your external BT Device.
FM RADIO:
1. Power on the unit as previously instructed.
2. Press the MODE Button on the Unit or Remote Control repeatedly indicator
“rAdI0” appear on the display to enter to Radio FM playback mode. Wait a few
seconds, radio frequency “XX.XX MHz” will appear on the display.
3. To store the available FM stations into the unit (up to 30 stations) at first time use
(or relocate the unit to a new location):
Press the ►II/PP Button on the unit or Remote Control. FM frequency on the
display will start running.
Wait a few minutes, the unit will automatically store all the available FM
stations into the memory then playback the first station.
4. Press the I◄◄ or ►►I buttons on the unit or Remote Control repeatedly to
select and play the stored FM station as desired.
5. If reception is weak, press and release the ◄◄ or ►► buttons on the Remote
Control repeatedly to fine tune.
6. Or, press and hold the ◄◄ or ►► buttons on the Remote Control until the FM
radio frequency on the display start running to automatically search and play the
next/previous available FM station.
Antennas:
This unit has a FM wire antenna on the rear of unit, which provides adequate reception
in most areas. If reception is weak, unwind and extended to its full length and/or
reassemble the other direction/location to improve the reception.

17
AUX (AUX/LINE IN):
Listen from an external Audio Player such as a Cell phone, MP3 Player, Discman …etc.
1. Connect one end of the Audio Connection Cable (not included) to the AUX
Out/Line Out/Phone Jack on the external Audio Player.
2. Connect the other end of the cable to the AUX (Aux/Line In) Jack on the front of
unit as illustrated below:
3. Power on the unit as previously instructed.
4. Press the MODE Button on the Unit or Remote Control repeatedly until “AUH”
appear on the display.
5. Play the music on the connected Player as usual. (Make sure the volume level of
the connected Audio Player is turned to high level.)

18
USB:
To play the music in external USB Device:
1. In standby mode, insert the USB Device into the USB Port on the front of unit as
illustrated below:
2. Power on the unit as previously instructed.
3. Press the Mode Button on the Unit or Remote Control repeatedly until “USb”
appear on the display to enter to USB playback mode.
4. Wait a few seconds, the unit will automatically play the first track on the USB
Device.
Note: If no USB Device was inserted into the USB Port. A few seconds later, the
unit will turn to CD playback mode automatically.
5. During playback:
Press the ►II/PP Button on the unit or Remote Control to pause, press again
to resume normal playback.
Press the I◄◄ or ►►I buttons repeatedly to skip tracks.
Press the ◄◄ or ►► buttons on the Remote Control to search the
specific section then press the ►II/PP Button to resume normal playback.