Magni ES0808H Setup guide

P.N.56622.B_EN
10/2020
‐‐ORIGINALINSTRUCTIONS‐‐
Drafted in accordance with the essential requirement of health and safety 1.7.4 of Annex I to Directive 2006/42 / EC
SELF-PROPELLED SCISSOR LIFTS
OPERATOR’S MANUAL
with Maintenance Information
(For ES0808H / ES1008H / ES0812H / ES1012H / ES1212H / ES1412H / ES1612HLB / ES1612HCP)
(For ES0808E / ES1008E / ES0812E / ES1012E / ES1212E / ES1412E / ES1612ELB / ES1612ECP)
( Hydraulic Motor / DC Motor Drive )
WARNING
THE MANIFACTURER SHALL NOT BE HELD LIABLE IN CASE OF
FAULTS OR ACCIDENTS DUE TO NEGLIGENCE, INCAPACITY,
INSTALLATION BY UNQUALIFIED TECHNICIANS AND IMPROPER USE
OF THE MACHINE.
DO NOT OPERATE THIS MACHINE UNTIL YOU READ AND
UNDERSTAND ALL THE DANGERS, WARNINGS AND CAUTIONS IN
THIS MANUAL.

OPERATOR’S MANUAL with Maintenance Information
Version of the Record
i
Version of the Record
VersionNumber Create Date
SM0110111MN_Rev1.0 ……………………………………………………………………… 2017-04
SM0110111MN_Rev2.0 ……………………………………………………………………… 2017-11
SM0110111MN_Rev3.0 ……………………………………………………………………… 2018-01
SM0110111MN_Rev4.0 ……………………………………………………………………… 2018-07
SM0110111MN_Rev4.1 ……………………………………………………………………… 2019-10
SM0110111MN_Rev4.2 ……………………………………………………………………… 2020-03
SM0110111MN_Rev4.3 ……………………………………………………………………… 2020-09
SM0110111MN_Rev5.0 ……………………………………………………………………… 2020-10

OPERATOR’S MANUAL with Maintenance Information
i
Important
Read, understand and obey these safety rules
and operating instructions before operating
this machine.
Only trained and authorized personnel shall be
permitted to operate this machine. This
manual should be considered a permanent
part of your machine and should remain with
the machine at all times. If you have any
questions, please call DINGLI Machinery.
Contents
Page
Safety Rules 1
Legend 10
Decals 11
Specifications 17
Control panel 34
Pre-operation Inspection 37
Workplace Inspection 39
Function Tests 40
Operating Instructions 45
Transport and Lifting Instructions 57
Storage 61
Maintenance 62
Schematic 91
Inspection and Repair Log 101
Owners, Users and operators:
We appreciate your choice of our machine for
your application. Our number one priority is
user safety, which is best achieved by our joint
efforts. We feel that you make a major
contribution to safety if you, as the equipment
users and operators:
1 Comply with employer, job site and
governmental rules.
2 Read, understand and follow the
instructions in this and other manuals
supplied with this machine.
3 Use good safe work practices in a
commonsense way.
4 Only have trained / certified operators,
directed by informed and knowledgeable
supervision, running the machine.
If there is anything in this manual that is not
clear or which you believe should be added,
please contact us.

OPERATOR’S MANUAL with Maintenance Information
ii
Contact us:
DISTRIBUTOR:
Magni Telescopic Handlers
Via Magellano 22,
41013 Castelfranco Emilia – Modena
Italia
Tel. [phone]
Fax: [phone]
Web: www.magnith.com
E-mail: [email protected]
MAKER:
Zhejiang Dingli Machinery Co., Ltd.
1255 Baiyun South Road. Leidian Town.
Deqing Zhejiang
China
Tel: [phone]
Fax: [phone]
Web: www.cndingli.com
E-mail:[email protected]

OPERATOR’S MANUAL with Maintenance Information
Safety Rules
1
Danger
Failure to obey the instructions and
safety rules in this manual will
result in death or serious injury.
Do Not Operate Unless:
√You learn and practice the principles of
safe machine operation contained in this
operator's manual.
1 Avoid hazardous situations.
Know and understand the safety rules
before going on to the next section.
2 Always perform a pre-operation
inspection.
3 Always perform function tests prior to
use.
4 Inspect the workplace.
5 Only use the machine as it was
intended.
√You read, understand and obey the
manufacturer's instructions and safety rules
— operator's manual and machine decals.
√You read, understand and obey employer's
safety rules and worksite regulations.
√You read, understand and obey all
applicable governmental regulations.
√You are properly trained to safely operate
the machine.
Decal Legend
DINGLI product decals use symbols, color
coding and signal words to identify the
following:
Safety alert symbol — used to alert
personnel to potential personal injury hazards.
Obey all safety messages that follow this
symbol to avoid possible injury or death.
Red — used to indicate the
presence of an imminently hazardous situation
which, if not avoided, will result in death or
serious injury.
Orange — used to indicate
the presence of a potentially hazardous
situation which, if not avoided, could result in
death or serious injury.
Yellow with safety alert
symbol — used to indicate the presence of a
potentially hazardous situation which, if not
avoided, may cause minor or moderate injury.
Blue without safety alert
symbol — used to indicate the presence of a
potentially hazardous situation which, if not
avoided, may result in property damage.

OPERATOR’S MANUAL with Maintenance Information
Safety Rules
2
Intended Use
This machine is intended to be used only to lift
personnel, along with their tools and materials
to an aerial work site.
Safety Sign Maintenance
Replace any missing or damaged safety signs.
Keep operator safety in mind at all times.
Use mild soap and water to clean safety signs.
Do not use solvent-based cleaners because
they may damage the safety sign material.
Electrocution Hazard
This machine is not electrically insulated and
will not provide protection from contact with or
proximity to electrical current.
Maintain safe distances from electrical power
lines and apparatus in accordance with
applicable governmental regulations and the
following chart.
Voltage
Phase to Phase
Minimum Safe
Approach Distance
Meters
0 to 300V Avoid Contact
300V to 50kV 3.05
50kV to 200kV 4.60
200kV to 350kV 6.10
350kV to 500kV 7.62
500kV to 750kV 10.67
750kV to 1000kV 13.72
Allow for platform movement, electrical line
sway or sag and beware of strong or gusty
winds.
Keep away from the machine if it contacts
energized power lines. Personnel on the
ground or in the platform must not touch or
operate the machine until energized power
lines are shut off.
Do not operate the machine during lightning or
storms.
Do not use the machine as a ground for
welding.
Tip-over Hazard
Occupants, equipment and materials must not
exceed the maximum platform capacity or the
maximum capacity of the platform extension.
Maximum capacity – ES0808H
Maximum occupants (Indoor use) 2
Maximum occupants (Outdoor use) 1
Platform allowable maximum load 380kg
Extension deck allowable maximum load 113kg
Maximum capacity – ES1008H
Maximum occupants (Indoor use ONLY) 2
Platform allowable maximum load 230kg
Extension deck allowable maximum load 113kg
Maximum capacity – ES0812H
Maximum occupants (Indoor / Outdoor use) 2
Platform allowable maximum load 540kg
Extension deck allowable maximum load 113kg
Maximum capacity – ES1012H
Maximum occupants (Indoor / Outdoor use) 2
Platform allowable maximum load 450kg
Extension deck allowable maximum load 113kg

OPERATOR’S MANUAL with Maintenance Information
Safety Rules
3
Maximum capacity – ES1212H
Maximum occupants (Indoor use) 2
Maximum occupants (Outdoor use) 1
Platform allowable maximum load 320kg
Extension deck allowable maximum load 113kg
Maximum capacity – ES1412H
Maximum occupants (Indoor use ONLY) 3
Platform allowable maximum load 320kg
Extension deck allowable maximum load 113kg
Maximum capacity – ES1612HLB
Maximum occupants (Indoor use ONLY) 2
Platform allowable maximum load 250kg
Extension deck allowable maximum load 113kg
Maximum capacity – ES1612HCP
Maximum occupants (Indoor use ONLY) 2
Platform allowable maximum load 250kg
Extension deck allowable maximum load 113kg
Maximum capacity – ES0808E
Maximum occupants (Indoor use) 2
Maximum occupants (Outdoor use) 1
Platform allowable maximum load 380kg
Extension deck allowable maximum load 113kg
Maximum capacity – ES1008E
Maximum occupants (Indoor use ONLY) 2
Platform allowable maximum load 230kg
Extension deck allowable maximum load 113kg
Maximum capacity – ES0812E
Maximum occupants (Indoor/Outdoor use) 2
Platform allowable maximum load 540kg
Extension deck allowable maximum load 113kg
Maximum capacity – ES1012E
Maximum occupants (Indoor/Outdoor use) 2
Platform allowable maximum load 450kg
Extension deck allowable maximum load 113kg
Maximum capacity – ES1212E
Maximum occupants (Indoor use) 2
Maximum occupants (Outdoor use) 1
Platform allowable maximum load 320kg
Extension deck allowable maximum load 113kg
Maximum capacity – ES1412E
Maximum occupants (Indoor use ONLY) 3
Platform allowable maximum load 320kg
Extension deck allowable maximum load 113kg
Maximum capacity – ES1612ELB
Maximum occupants (Indoor use ONLY) 2
Platform allowable maximum load 250kg
Extension deck allowable maximum load 113kg
Maximum capacity – ES1612ECP
Maximum occupants (Indoor use ONLY) 2
Platform allowable maximum load 250kg
Extension deck allowable maximum load 113kg
Platform retracted Platform extended
Extension Platform
only only
Work Area Safety
Do not raise the platform unless the machine
is on a firm, level surface.
Do not drive over 0.8 km/h with the platform
raised.

OPERATOR’S MANUAL with Maintenance Information
Safety Rules
4
Do not depend on the tilt alarm as a level
indicator. The tilt alarm sounds on the chassis
and in the platform when the machine is on a
slope.
If the tilt alarm sounds:
Lower the platform. Move the machine to a
firm, level surface. If the tilt alarm sounds
when the platform is raised, use extreme
caution to lower the platform.
For outdoor use machine, do not raise the
platform when wind speeds may exceed 12.5
m/s. If wind speeds exceed 12.5 m/s when the
platform is raised, lower the platform and do
not continue to operate the machine.
Do not operate the machine in strong or gusty
winds. Do not increase the surface area of the
platform or the load. Increasing the area
exposed to the wind will decrease machine
stability.
Do not use the platform controls to free a
platform that is caught, snagged or otherwise
prevented from normal motion by an adjacent
structure. All personnel must be removed from
the platform before attempting to free the
platform using the ground controls.
Use extreme care and slow speeds while
driving the machine in the stowed position
across uneven terrain, debris, unstable or
slippery surfaces and near holes and
drop-offs.
Do not drive the machine on or near uneven
terrain, unstable surfaces or other hazardous
conditions with the platform raised.
Do not push off or pull toward any object
outside of the platform.
Maximum allowable manual force
Model Application
manual
force
Maximum
occupants
ES0808H Outdoor 200N 1
Indoor 400N 2
ES1008H Indoor 400N 2
ES0812H Outdoor 400N 2
Indoor 400N 2
ES1012H Outdoor 400N 2
Indoor 400N 2
ES1212H Outdoor 200N 1
Indoor 400N 2
ES1412H Indoor 400N 3
ES1612HLB Indoor 400N 2
ES1612HCP Indoor 400N 2
ES0808E Outdoor 200N 1
Indoor 400N 2
ES1008E Indoor 400N 2
ES0812E Outdoor 400N 2
Indoor 400N 2
ES1012E Outdoor 400N 2
Indoor 400N 2
ES1212E Outdoor 200N 1
Indoor 400N 2
ES1412E Indoor 400N 3
ES1612ELB Indoor 400N 2
ES1612ECP Indoor 400N 2

OPERATOR’S MANUAL with Maintenance Information
Safety Rules
5
Do not use the machine as a crane.
Do not place or attach fixed or overhanging
loads to any part of this machine.
Do not push the machine or other objects with
the platform.
Do not operate the machine with the chassis
trays open.
Do not contact adjacent structures with the
platform.
Do not alter or disable the limit switches.
Do not tie the platform to adjacent structures.
Do not place loads outside the platform
perimeter.
Do not alter or disable machine components
that in any way affect safety and stability.
Do not replace items critical to machine
stability with items of different weight or
specification.
Do not use batteries that weigh less than the
original equipment. Batteries are used as
counterweight and are critical to machine
stability. Each battery must weigh 28 kg. The
batteries must weigh a minimum of 112 kg.
(For ES0808H/E, ES1008H/E, ES0812H/E,
ES1012H/E); Each battery must weigh 30 kg.
The batteries must weigh a minimum of 120 kg
(For ES1212H/E); Each battery must weigh 37
kg. The batteries must weigh a minimum of
148 kg (For ES1412H/E, ES1612HLB/ELB,
ES1612HCP/ECP).
Do not modify or alter an aerial work platform
without prior written permission from the
manufacturer. Mounting attachments for
holding tools or other materials onto the
platform, toe boards or guard rail system can
increase the weight in the platform and the
surface area of the platform or the load.
Do not place ladders or scaffolds in the
platform or against any part of this machine.
Do not transport tools and materials unless
they are evenly distributed and can be safely
handled by person(s) in the platform.
Do not use the machine on a moving or mobile
surface or vehicle.
Be sure all tires are in good condition, air-filled
tires are properly inflated and lug nuts are
properly tightened.
Crushing Hazard
Keep hands and limbs out of scissors.
Keep hands clear when folding rails.
Maintain a firm grasp on the platform rail when
removing the rail pins. Do not allow the
platform guard rails to fall.
Use common sense and planning when
operating the machine with the controller from
the ground. Maintain safe distances between
the operator, the machine and fixed objects.
Operation on Slopes Hazard
Do not drive the machine on a slope that
exceeds the slope and side slope rating of the
machine.
Slope rating applies to machines only in the
stowed position.
Maximum slope rating stowed

OPERATOR’S MANUAL with Maintenance Information
Safety Rules
6
Maximum side slope rating stowed
Model A B
ES0808H 25% (14°) 25% (14°)
ES1008H 25% (14°) 25% (14°)
ES0812H 25% (14°) 25% (14°)
ES1012H 25% (14°) 25% (14°)
ES1212H 25% (14°) 25% (14°)
ES1412H 25% (14°) 25% (14°)
ES1612HLB 25% (14°) 25% (14°)
ES1612HCP 25% (14°) 25% (14°)
ES0808E 25% (14°) 25% (14°)
ES1008E 25% (14°) 25% (14°)
ES0812E 25% (14°) 25% (14°)
ES1012E 25% (14°) 25% (14°)
ES1212E 25% (14°) 25% (14°)
ES1412E 25% (14°) 25% (14°)
ES1612ELB 25% (14°) 25% (14°)
ES1612ECP 25% (14°) 25% (14°)
Note: Slope rating is subject to ground
conditions and adequate traction.
Fall Hazard
The guard rail system provides fall protection.
During operation, occupants in the platform
must wear a full body harness with a lanyard
attached to an authorized lanyard anchorage
point. Attach only one (1) lanyard per lanyard
anchorage point.
Do not sit, stand or climb on the platform guard
rails. Maintain a firm footing on the platform
floor at all times.
Do not climb down from the platform when
raised.
Keep the platform floor clear of debris.
Close the entry gate before operating.
Do not operate the machine unless the guard
rails are properly installed and the entry is
secured for operation.
Do not enter or exit the platform unless the
machine is in the stowed position.
Collision Hazard
Be aware of limited sight distance and blind
spots when driving or operating.
Be aware of extended platform position(s)
when moving the machine.
Check the work area for overhead obstructions
or other possible hazards.
Be aware of crushing hazards when grasping
the platform guard rail.

OPERATOR’S MANUAL with Maintenance Information
Safety Rules
7
Operators must comply with employer, job site
and governmental rules regarding use of
personal protective equipment.
Observe and use color-coded direction arrows
on the platform controls for drive and steer
functions.
Do not operate a machine in the path of any
crane or moving overhead machinery unless
the controls of the crane have been locked out
and/or precautions have been taken to prevent
any potential collision.
No stunt driving or horseplay while operating a
machine.
Do not lower the platform unless the area
below is clear of personnel and obstructions.
Limit travel speed according to the condition of
the ground surface, congestion, slope, location
of personnel, and any other factors which may
cause collision.
Component Damage Hazard
Do not use any battery charger greater than
24V to charge the batteries.
Do not use the machine as a ground for
welding.
Explosion and Fire Hazard
Do not operate the machine or charge the
batteries in hazardous locations where
potentially flammable or explosive gases or
particles may be present.
Damaged Machine Hazard
Do not use a damaged or malfunctioning
machine.
Conduct a thorough pre-operation inspection
of the machine and test all functions before
each work shift. Immediately tag and remove
from service a damaged or malfunctioning
machine.
Be sure all maintenance has been performed
as specified in this manual.
Be sure all decals are in place and legible.
Be sure the operator’s manual is complete,
legible and in the storage container located in
the platform.
Bodily Injury Hazard
Do not operate the machine with a hydraulic oil
or air leak. An air leak or hydraulic leak can
penetrate and/or burn skin.
Improper contact with components under any
cover will cause serious injury. Only trained
maintenance personnel should access
compartments. Access by the operator is only
advised when performing a pre-operation
inspection. All compartments must remain
closed and secured during operation.
Battery Safety
Burn Hazard
Batteries contain acid. Always wear protective
clothing and eye wear when working with
batteries.
Avoid spilling or contacting battery acid.
Neutralize battery acid spills with baking soda
and water.

OPERATOR’S MANUAL with Maintenance Information
Safety Rules
8
Rinse eyes or skin splashed with acid using
plenty of clean water and consult a doctor
immediately. Wash clothing contaminated with
acid with plenty of water.
Explosion Hazard
Keep sparks, flames and lighted tobacco away
from batteries. Batteries emit explosive gas.
Avoid fire and risk of explosion caused by
short circuits.
The battery tray should remain open during the
entire charging cycle.
Do not contact the battery terminals or the
cable clamps with tools that may cause
sparks.
Component Damage Hazard
Do not use any battery charger greater than
24V to charge the batteries.
Pressure relief valves are used as breathable
plugs. If open the pressure relief valves, the
battery will be destroyed.
The battery must always be kept clean and dry
in order to prevent leakage currents. Do not
rinse with water or wipe with a wet towel.
Please do not change the location of the
battery, and cannot be inverted. Do not block
the vent hole of safety valve when placing.
The series/parallel connection must be
approved by Dingli. Only accessories
approved by Dingli can be used for connection
of battery blocks.
Electrocution/ Burn Hazard
Connect the battery charger to
a grounded, AC 3-wire
electrical outlet only.
Inspect daily for damaged cords, cables and
wires. Replace damaged items before
operating.
Metallic parts of the battery cells are always
electriferous. Therefore, no foreign objects or
tools may be placed on the batteries.
Avoid electrical shock from contact with
battery terminals. Remove all rings, watches
and other jewelry.
Tip-over Hazard
Do not use batteries that weigh less than the
original equipment. Batteries are used as
counterweight and are critical to machine
stability. Each battery must weigh 28 kg. The
batteries must weigh a minimum of 112 kg.
(For ES0808H/E, ES1008H/E, ES0812H/E,
ES1012H/E); Each battery must weigh 30 kg.
The batteries must weigh a minimum of 120 kg
(For ES1212H/E); Each battery must weigh 37
kg. The batteries must weigh a minimum of
148 kg (For ES1412H/E, ES1612HLB/ELB,
ES1612HCP/ECP).
Lifting Hazard
Use the appropriate number of people and
proper lifting techniques when lifting batteries.
Lifting hooks must not cause any damage to
cells, connectors or connecting cables.
Environmental Hazard
30°C battery temperature is considered the
rated temperature. Higher temperatures
reduce the service life, while lower
temperatures reduce the available
capacity.45°C is the upper limit temperature
and is not permissible as an operating
temperature.
Batteries must not be exposed to sunlight
without protection.

OPERATOR’S MANUAL with Maintenance Information
Safety Rules
9
Transportation and storage
Hazard
Charge the battery as soon as receive the
machine or after long distance transportation
When the battery is stored for a long time, it
needs to be charged regularly. Failure to
charge in time may permanently damage the
battery.
pollute Hazard
Old batteries with this marking are recyclable
goods and must be sent for recycling.
Used batteries which are not sent for recycling
are to be disposed of as special waste under
the relevant regulations
Lockout after Each Use
1 Select a safe parking location - firm level
surface, clear of obstruction and traffic.
2 Lower the platform.
3 Turn the key switch to the off position and
remove the key to secure from
unauthorized use.
4 Push in the red Emergency Stop buttons to
“off” position.
5 Push in the main power switch to “off”
position
6 Chock the wheels.
7 Charge the batteries.

OPERATOR’S MANUAL with Maintenance Information
Legend
10
Legend
1 Platform extension
2 Manual storage container
3 Platform control
4 Lanyard anchorage point
5 Platform guard rails
6 Platform extension release pedal
7 Main platform
8 Platform entry gate
9 Scissor arms
10 Lift cylinder
11 Ground controls (on opposite side of
machine)
12 Entry ladder
13 Brake release pump
14 Non-steer tire
15 Battery charger
16 Pothole guard
17 Steer tire
18 Safety arm
1
23
4
5
7
8
9
10
6
18
17
11
12
13
14
15
16

OPERATOR’S MANUAL with Maintenance Information
Decals
11
Decal Inspection
Use the pictures on the next page to verify that all decals are legible and in place.
Below is a numerical list with quantities and descriptions.
No. Part No. Description Qty. Remark
1 37422 Decal, Label-Lanyard anchorage point 4
2 37424 Decal, Symbols-Refer the operator to the
instructions for use 2
3 37416 Decal, Symbols-Tip-over hazard, tilt-alarm 1
4 44344 Decal, Instructions-Directional arrows 1
5 37440 Decal, Symbols-General safety rules 1
6
38256 Decal, Label-Capacity 380kg 1 ES0808H,ES0808E
34868 Decal, Label-Capacity 230kg 1 ES1008H,ES1008E
70960 Decal, Label-Capacity 540kg ES0812H,ES0812E
34869 Decal, Label-Capacity 450kg 1 ES1012H,ES1012E
34871 Decal, Label-Capacity 320kg 1 ES1212H,ES1212E
34872 Decal, Label-Capacity 320kg 1 ES1412H,ES1412E
51918 Decal, Label-Capacity 250kg 1 ES1612HLB,ES1612ELB,
ES1612HCP, ES1612ECP
7 34925 Decal, Instructions-Forklift pockets 2
8
38253 Decal, Instructions-Maximum wheel load: 1000kg 4 ES0808H,ES0808E
ES0812H,ES0812E
37403 Decal, Instructions-Maximum wheel load: 960kg 4 ES1008H,ES1008E
38249 Decal, Instructions-Maximum wheel load: 1240kg 4 ES1012H,ES1012E
37405 Decal, Instructions-Maximum wheel load: 1310kg 4 ES1212H,ES1212E
37407 Decal, Instructions-Maximum wheel load: 1280kg 4 ES1412H,ES1412E
37406 Decal, Instructions-Maximum wheel load: 1350kg 4 ES1612HLB,ES1612ELB,
ES1612HCP, ES1612ECP
9 34240.A Decal, Symbols-Main power switch operation 1
10 43805 Decal, Symbols-Battery charging instructions 1
11 34929 Decal, Label-CE 3
12 37429 Decal, Symbols-Explosion/burn hazard 1
13 37432 Decal, Symbols-Electrocution hazard 2

OPERATOR’S MANUAL with Maintenance Information
Decals
12
No. Part No. Description Qty. Remark
14 66482 Decal, Symbols-Charge warning 1
15
37421 Decal, Symbols-Keep away from moving parts 3
ES0808H,ES0808E
ES1008H,ES1008E
ES0812H,ES0812E
ES1012H,ES1012E
ES1212H,ES1212E
37421 Decal, Symbols-Keep away from moving parts 5
ES1412H,ES1412E
ES1612HLB,ES1612ELB,
ES1612HCP,ES1612ECP
16
37430 Decal, Symbols-Safety arm 2
ES0808H,ES0808E
ES1008H,ES1008E
ES0812H,ES0812E
ES1012H,ES1012E
ES1212H,ES1212E
37430 Decal, Symbols-Safety arm 4
ES1412H,ES1412E
ES1612HLB,ES1612ELB,
ES1612HCP,ES1612ECP
17
37467 Decal, Symbols-Max. manual force 400N (Indoor)
200N (Outdoor) 2 ES0808H,ES0808E
ES1212H,ES1212E
37507 Decal, Symbols-Max. manual force 400N (Indoor) 2
ES1008H,ES1008E
ES1612HLB,ES1612ELB,
ES1612HCP,ES1612ECP
38250 Decal, Symbols-Max. manual force 400N (Indoor)
400N (Outdoor) 2 ES0812H,ES0812E
ES1012H,ES1012E
44465 Decal, Symbols-Max. manual force 400N (Indoor) 2 ES1412H, ES1412E
18
38258 Decal, Cosmetic-ES0808H 2 ES0808H
38254 Decal, Cosmetic-ES0808E 2 ES0808E
38252 Decal, Cosmetic-ES1008H 2 ES1008H
34212 Decal, Cosmetic-ES1008E 2 ES1008E
70974 Decal, Cosmetic-ES0812H 2 ES0812H
70973 Decal, Cosmetic-ES0812E 2 ES0812E
38243 Decal, Cosmetic-ES1012H 2 ES1012H
38244 Decal, Cosmetic-ES1012E 2 ES1012E
37410 Decal, Cosmetic-ES1212H 2 ES1212H
34213 Decal, Cosmetic-ES1212E 2 ES1212E
37411 Decal, Cosmetic-ES1412H 2 ES1412H
34211 Decal, Cosmetic-ES1412E 2 ES1412E

OPERATOR’S MANUAL with Maintenance Information
Decals
13
No. Part No. Description Qty. Remark
18
52144 Decal, Cosmetic-ES1612HLB 2 ES1612HLB
52142 Decal, Cosmetic-ES1612ELB 2 ES1612ELB
52143 Decal, Cosmetic-ES1612HCP 2 ES1612HCP
52145 Decal, Cosmetic-ES1612ECP 2 ES1612ECP
19 38437 Decal, Symbols-Do not alter or disable limit switch 1
20 34926 Decal, Instructions-Tie down point 4
21 34928 Decal, Instructions-Lift point 4
22 37427 Decal, Symbols-Emergency lower 1
23 37433 Decal, Symbols-Injection hazard 1
24 43807 Decal, Symbols-Platform power instructions 1

OPERATOR’S MANUAL with Maintenance Information
Decals
14
Safety tape
1
2
3
45
1
11
6
7
20
21
9
12
13
16
17
18
8
15
7
20 21
8
17
18
16
15
19
22
23
15
20
21
20
21
8
8
10
11
24
11
13
2
11
14

OPERATOR’S MANUAL with Maintenance Information
Decals
15