Magnum Industrial MI-93500 User manual

MODEL NO.: MI-93500
SPECIFICATIONS
Speeds: 60Hz 82, 132, 170, 235FPM Blade: 27MMx0.9MMx3300MM
(1″x0.032″x130″)
Motor: 60Hz 2HP 1725RPM 1PHASE Dimension: L:1730MMxW:760MM
(L68″xW30″)
Capacity: 90°● 250MM ▄ 250x415MM ▄ 200x450MM Blade Wheels: 355MM (14″) Diameter
90°● 10″ ▄ 10″x16-1/2″ ▄ 8″x18″ Shipping Weight: 320KGS/360KGS
45°● 190MM ▌250x190MM
45°● 7-1/2″ ▌10″x7-1/2″
10”
METAL CUTTING BANDSAW

WARNING
For Your Own Safety Read Instruction
Manual Before Operating Saw
a) Wear eye protection.
b) Do not remove jammed cutoff pieces until blade has stopped.
c) Maintain proper adjustment of blade tension, blade guides, and thrust bearings.
d) Adjust upper guide to just clear workpiece.
e) Hold workpiece firmly against table.
1. KEEP GUARDS IN PLACE and in working order.
2. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting
wrenches are removed from tool before turning it on.
3. KEEP WORKAREA CLEAN. Cluttered areas and benches invite accidents.
4. DON’T USE IN DANGEROUS ENVIRONMENT. Don’t use power tools in damp or wet locations, or expose
them to rain. Keep work area well lighted.
5. KEEP CHILDREN AWAY. All visitors should be kept safe distance from work area.
6. MAKE WORKSHOP KID PROOF with padlocks, master switches, or by removing starter keys.
7. DON’T FORCE TOOL. It will do the job better and safer at the rate for which it was designed.
8. USE RIGHT TOOL. Don’t force tool or attachment to do a job for which it was not designed.
9. This tool should be connected to a ground metal permanent wiring system; or to a system having an
equipment-grounding conductor.
10. WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry
which may get caught in moving parts. Nosily footwear is recommended. Wear protective hair covering to
contain long hair.
11. ALWAYS USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty. Everyday
eyeglasses only have impact resistant lenses, they are NOT safety glasses.
12. SECURE WORK. Use clamps or a vise to hold work when practical. It’s safer than using your hand and it frees
both hands to operate tool.
13. DON’T OVERREACH. Keep proper footing and balance at all times.
14. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow
instructions for lubricating and changing accessories.
15. DISCONNECT TOOLS before servicing; when changing accessories, such as blades, bits, cutters, and the
like.
16. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in off position before plugging in.
17. USE RECOMMENDED ACCESSORIES. Consult the owner’s manual for recommended accessories. The use
of improper accessories may cause risk of injury to persons.
18. NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting tool is unintentionally
contacted.
19. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be
carefully checked to determine that it will operate properly and perform its intended function–check for
alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that
may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.
20. DIRECTION OF FEED. Feed work into a blade or cutter against the direction of rotation of the blade or cutter
only.
21. NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Don’t leave tool until it comes to a
complete stop.
1

ELECTRICAL CONNECTION/DISCONNECTION.
FOR 3 PHASE
1. Electrical connection:
a. A cable with four wires is equipped to connect your machine into the 3 phase power supply. Please connect
your machine into the power supply with hand-operated disconnecting device, which is in compliance with
subclause 5.3 of EN 60204, such as no fuse breaker or plug/socket combination.
b. For the protection of control device, we recommend the operator to supply a fuse with appropriate current
rating, and the total length between fuse and connection terminal shall not exceed 1.5 m.
c. The power supply system is TN system.
d. The exact power source voltage, frequency, and number of phase shall be checked according to the installation
diagram and circuit diagram.
e. The correct direction of saw blade should be checked after connecting.
2. Electrical disconnection:
a. The disconnection is carried out by hand-operated disconnecting device, which is on the door of control box as
an option or connected before the power source.
b. Be sure to disconnect this machine from power source, when you want to stop the job, maintenance, and
adjustment.
3. Grounding:
The grounding of this model is carried out by connecting the yellow/green terminal of supply cable to the
grounding terminal of power source. Be sure to ground your machine before connecting machine to power
source in any situation.
WARNING !
Do not disconnect grounding terminal before disconnecting power source.
FOR SINGLE PHASE
1. If the power cable is not equipped with plug, please connect and disconnect your machine with power
according to the same instruction of three phase. Otherwise, please follow the following instruction (2~4).
2. The connection, disconnection, and grounding is carried out through the plug, equipped on the machine. For
the safety reason, Do not change this plug into any other type in any situation.
3. For the protection of control device, we recommend the operator to supply a fuse with appropriate current
rating, and the total length between fuse and connection terminal shall not exceed 1.5m.
4. The exact power source voltage, frequency, and number of phase shall be checked according to the installation
diagram and circuit diagram.
2

3

4