MAKEiD T1 Series User manual

T1 Series Label Printer
User Manual

Copyright Statement
Edition 1.0 issued in April 2018
All rights reserved 2018MAKEiD Printer
This manual includes the professional information of
Chongqing Jingranyouxu Science and Technology Co.,
Ltd., which are only for commercial customers’ reading
and reference. The contents herein shall not be used,
copied or spreaded, publicized by any means for any
reason or purpose without the written permission of
Chongqing Jingranyouxu Science and Technology Co.,
Ltd., otherwise, we will investigate and affix the legal
liability.
Chongqing Jingranyouxu Science and Technology Co.,
Ltd. reserves the amendment right without further no-
tice.
Trademark
MAKEiD is the registered trademark of Chongqing
Jingranyouxu Science and Technology Co., Ltd.
Microsoft is the registered trademark of Microsoft Cor-
poration.
Windows is the registered trademark of Microsoft Cor-
poration.

Contents
Foreword.................................................... 1
Disclaimer .................................................. 2
Safety Instructions...................................... 3
1.1 Overview .............................................. 8
1.2 Unpacking ............................................ 8
1.3 Packing List.......................................... 8
1.4 Main Parts............................................ 9
1.5 Technical Parameters and Specification
................................................................. 10
................................................................. 12
2.1 Installation of Label Box and Cautions 12
2.1.1 Check the label box and make sure that all
parts are in good status and there is no breakage
or other problems. ............................................ 12
2.1.2 Insert the label box into the printer as
shown in Figure 2-1. Close the printer cover. .. 12
3.1 Printer Operation................................ 13
1. Power on the printer.......................... 13
2. Turn on the printer............................. 13
3. Alarm................................................. 14
4. Print test............................................ 14
10. Turn off the printer............................. 14
3.2 Description of Indicators..................... 14
3.4 Connect a mobile device to operate the
printer....................................................... 14
Chapter IV Maintenance........................... 15

4.1 Preparation before maintenance:........ 15
4.2 Cleaning of the Label Box Reader...... 15
4.3 Maintenance of Print Head................. 16
4.5 Cleaning of Internal Space ................. 16
Chapter V Failure Treatment................. 17
5.1 Failure Indication................................ 17
5.2 Minor Failures..................................... 18
1. Failure of print head .......................... 18
2. Shutdown of printer........................... 18
3. The printing quality is not good......... 18
4. The printer cannot be turned off........ 18
5.3 Failure due to other unknown causes. 19
Annex....................................................... 19

Foreword
Dear users:
Thanks for choosing T1 series portable label printer
designed and manufactured by Chongqing
Jingranyouxu Science and Technology Co., Ltd.
T1 series portable label printer is a light, handy and
convenient thermal wax printer which can realize print-
ing via mobile phone, tablet PC and other devices. It is
with good performance, easy operation, durability and
wide application range.
This manual specifies the installation, operation and
maintenance of printer, cautions for operation, setting
and maintenance and solutions for minor failures.
Please read this manual carefully before operation and
keep it properly for further use.

Disclaimer
This manual expounds the specification and instruc-
tions. However, specification and configuration of the
printers manufactured thereafter may be altered. The
manufacturer and dealers will not be responsible for
any direct or indirect loss arising from the difference
between manual and the printer.
This manual lists problems that may occur, however,
unforeseen situation may occur during use. For any
problem during printer operation, such as failure to
work, defect or unclearness of printed contents, the
manufacturer and dealers are only responsible for fail-
ure debugging (in line with the articles of warranty
card) rather than other direct or indirect loss therefrom,
including but not limited to loss of business interest,
business interruption, business information and other
financial loss.

Safety Instructions
Personal safety is all-important during operation and
maintenance. Warnings and cautions for printer opera-
tion are detailed in this manual. Please read carefully
before operation and maintenance.
Do not try to repair or adjust it by yourself. In case that
the failure cannot be solved in line with this manual,
please turn off the printer! Disconnect the power
supply.
Please contact Customer Service Dept. of Chongqing
Jingranyouxu Science and Technology Co., Ltd. via
400-158-9100 for help.
Marks
To ensure safety during operation, please pay attention
to the following marks.
Warning: this mark indicates that the items shall
be paid special attention to. Financial loss
or personnel injury may occur in case of
improper use.
Note: this mark indicates that the items shall be
paid attention to. Material damage may oc-
cur or the printer may fail to work in case of
improper use.
Cautions for printer operation
•Please take out the label at the exit after
printing, otherwise sluggish printing may oc-
cur.
•Do not disassemble the printer, otherwise
electric shock, personal injury due to rotating
part, part damage and other accidents may

occur.
•In case of abnormalities, such as smoking
and odor, please disconnect the power sup-
ply to avoid burn.
•Do not take out the label box during printing,
otherwise unforeseen circumstances may
occur.
•The printer is hot after printing. Do not touch
it, otherwise scald may occur.
•Do not use inferior label box (the ones not
manufactured by MAKEiD), otherwise the
print head may be damaged and the service
life of printer may be shortened. Damage of
print head due to inferior materials is not in-
cluded in the warranty range.
•Do not touch the print head, otherwise sens-
ing element may be damaged due to static
electricity.
•Please turn off the power if the printer will
not be used for a long time.
•Do not press or strike the printer, otherwise
the part may be damaged or the printer
working may be abnormal.
•In case of soaking or crash of printer or bat-
tery, please do not use the printer and make
it repair at the maintenance center designat-
ed by MAKEiD.
•To ensure the printing effect and avoid dam-
age of print head, please do not use the
printer at the environment with a tempera-

ture below ０℃ and a relative humidity over
80%. Meanwhile, when the temperature dif-
ference between indoor area and outdoor
area is large, do not use the printer immedi-
ately after taking it into indoor area. Please
use it after the printer has no frosting.
•The print head is a precise part. To better
protect the print head and extend the service
life, the suggested workload is as follows:
* The single printing length shall not ex-
ceed two meters
* The printing length per day shall not ex-
ceed twenty meters
•Temperature of the print head may be high
after continuous printing. Please be careful
during operation so as to avoid burn.
•Do not scrape the print head with hard ob-
ject. Damage of print head due to improper
maintenance and use are not included in the
warranty range.
•The print head is a quick-wear part. To avoid
corrosion, please pay attention to the follow-
ing items:
*Do not touch the print head with hands;
*Do not use ribbon and thermo-sensitive
paper with Na, K and CI ions;
*The print head cannot contact any liq-
uid or moist object;
*Only anhydrous alcohol is applicable for
print head cleaning.

Cautions for battery use
Please read this manual and mark on the battery care-
fully before operation. Do not remove the battery op-
tionally.
•Please store the charged battery properly.
Contact between battery electrode and con-
ductor such as key and jewelry may cause
short circuit, hot, even burn and property
loss or personal injury.
•Do not place battery in fire, otherwise elec-
trolyte leakage may occur. In case that the
electrolyte gets into eyes, do not knead with
hands. Clean eyes with water. In case of se-
rious damage, go to a doctor for treatment. If
the electrolyte spills on skin or clothes, clean
it with water immediately.
•Do not place battery in water, internal short
circuit may occur. In this case, the battery
will get hot, smoke, deform, damage, even
explore.
•The battery is with special circuit protection
and device. Do not open it optionally, other-
wise short circuit or electrolyte leakage may
occur.
•Please use the genuine battery. Battery
made by other manufacturers may cause
burn of printer or injury of operator. Damage
arising from non-genuine battery shall not be
included in the warranty range and the man-
ufacturer and dealers shall bear no respon-
sibility therefrom.
•Replace the battery immediately in case of
color change or deformation.

•Do keep battery out of reach of children so
as to avoid damage.
Cautions for power adapter
Please read this manual and mark on the power
adapter carefully before operation.
•Do not use damaged or worn power line,
otherwise electric shock or fire may occur.
•Do not contact the power adapter, power
plug and power output with wet hand, other-
wise electric shock may happen.
•Do not overbend or pull the power line hard
and do not place heavy articles on it, other-
wise it may be damaged and fire or electric
shock may occur.
•When pulling out the power plug, just hold
the plug and do not pull the power line, oth-
erwise it may be damaged and fire or electric
shock may occur.
•Do keep power adapter out of reach of chil-
dren so as to avoid damage.
•Disconnect power supply before printer
maintenance so as to avoid damage.
•No power adapter is provided with the print-
er. All standard USB plugs are applicable to.

1.1 Overview
T1 series portable label printer is a smart, portable and
interconnected label printer manufactured by Chong-
qing Jingranyouxu Science and Technology Co., Ltd.
With MAKEiD APP, it can realize printing via mobile
phone and tablet PC.
1.2 Unpacking
After receiving the printer, check it carefully. In case of
damage during transportation, claim against the carrier
immediately. If there is no damage, check the acces-
sories in line with the packing list. For any short item,
please contact with the dealer immediately.
1.3 Packing List
Packing list (product in kind prevails)
1. Printer 1pc
2. USB cable 1pc
3. Label box 1pc
4. User manual (including warranty card and certifi-
Product Introduction
Chapter I
1. Check the printer carefully for damage or scratch.
For any damage during transportation, MAKEiD will
bear no responsibility.
2. Please keep the packaging box for transfer in the
future.

cate of qualification) 1pc
1.4 Main Parts
1. Label output 2. Label
3. Printer cover 4. Indicator
5. USB interface 6. Power button
7. Reset
Fig. 1-1
Label
output
Label
Printer
cover
Indicator
USB
interface
Reset
Power
button

1. Label box reader 2. Print head
3. Paper outlet
1.5 Technical Parameters and Specification
Table 1-1 Specification and Parameters of Printer
Function and
Specification
Parameters
Printing method
Thermal printing
Paper detection
mode
Reflection-type
Fig. 1-2

Processor
STM32F401
Resolution
178dpi
Interface
Type-C, bluetooth
Effective printing
width
18mm
Maximum print-
ing speed
15mm/s
Width of roll
label
12Mm, 16mm, 20mm,
24mm
Outer diameter
of roll label
Maximum outer diame-
ter: 36mm
Inner diameter: 18mm
Label thickness
0.06～0.15mm
Printer dimen-
sion
56*130*101mm
Weight
0.4kg
Working envi-
ronment
Temperature: 15~35℃
Relative humidity:
30~80% (non-
condensing)
Storage envi-
ronment
Temperature: -10~55℃
Relative humidity:
5~80% (non-condensing)
Table 1-2 Specification of Power Adapter

Function and Specifi-
cation
Parameters
INPUT
5V 1A
2.1 Installation of Label Box and Cautions
2.1.1 Check the label box and make sure that all
parts are in good status and there is no breakage or
other problems.
2.1.2 Insert the label box into the printer as shown in
Figure 2-1. Close the printer cover.
Installation
Chapter II

Please take good care of the environment. The old
label box belongs to recyclable garbage. Please do
not throw it away at will.
3.1 Printer Operation
1. Power on the printer
•Li-ion battery pack: 7.4V, 1200mAh
•Power adapter
*Input: 5V 1A
*When the printer is turned on, the indicator
indicates nothing after the adapter connect-
ed. When the printer is turned off, the light-
ing will flash after the adapter connected
and it means the printer is not fully charged.
The green lighting is normally on when the
printer is fully charged.
2. Turn on the printer
Press down the power button for two seconds. The
printer is ready after the green lighting is normally on.
Figure 2-1 Installation Diagram of Label Box
Printer Operation
Chapter III

3. Alarm
•Battery alarm: when the battery level is low, the
red lighting will flash. If the printer is interconnected
to a mobile phone, an alarm of low battery will show
on the APP.
4. Print test
When the printer is turned on, connect the mobile
phone to the printer and perform self-inspection on the
APP.
8. Printer Setting
When the printer is turned on, users can set up print-
ing parameters via the APP according to the cases.
9. Print
When the printer is turned on, users can edit contents
on the APP and then print it out.
10. Turn off the printer
When the printer is turned on, press down the power
button for two seconds. After the indicator extin-
guishes, release it, then the printer will be turned off.
3.2 Description of Indicators
•Turnon: the green lighting is normally on
•Failure: the red lighting flashes
•Charging (when the printer is turned off): the
green lighting flashes
•Fully charged (when the printer is turned off): the
green lighting is normally on
3.4 Connect a mobile device to operate the
printer
The printer is with bluetooth, which can connect to
mobile devices. The wireless printing software has
label templates. Users can use the template for edit-
ing, then print it out. When a mobile device is connect-
ed to the printer and the label template inputted and
the built-in template are inconsistent, the later one will

be chosen.
•Note Please choose wireless editing soft-
ware matching with the mobile device
(please see the installation QR code in the
annex herein).
Chapter IV Maintenance
4.1 Preparation before maintenance:
•Please read the “Safety Instructions” herein
carefully before printer maintenance.
•Use anhydrous alcohol with a concentration
over 99% for cleaning.
•Do disconnect the power supply before
printer maintenance.
4.2 Cleaning of the Label Box Reader
Dust and dirt is harmful to the contact between label
box reader and label box sensing chip. Do clean it
timely as required hereunder:
•Turn off the power;
•Open the cover and take the label box out;
•Use a piece of soft cloth (lens wiping paper) with
anhydrous alcohol to clean the surface of sensing
chip gently. The alcohol shall not permeate into the
product.
•Do not clean the operation panel with corrosive
organic solvents, such as machine cleaner and in-
Maintenance
Chapter IV

dustrial alcohol.
4.3 Maintenance of Print Head
To ensure the printing quality and reduce damage of
print head from paper scrap, sand, dust particle, glue
and other materials, it is suggested that the print head
shall be cleaned once every month if it is used fre-
quently and it shall be cleaned before each use if it is
not used frequently. Cleaning procedure:
•Turn off the power;
•Open the cover and take the label box out;
•Use swabs with anhydrous alcohol to clean the
print head. Clean it repeated until there is no more
dirt on the swab, which means the print head is
clean.
4.5 Cleaning of Internal Space
A clean internal space is good for the print head and
can effectively extend the service life of print head.
Use cotton cloth with anhydrous alcohol to clean the
surfaces of all internal parts.