MAKFRY pan 202 User manual

USER MANUAL
WWW.MAKFRY.COM
PAN 202
BREADING UNIT

CONTENTS
1- GENERAL INFORMATION
2- PRODUCT INTRODUCTION
3- TECHNICAL SPECIFICATIONS
4- PRODUCT SCHEME
5- TRANSPORTATION AND STORAGE CONDITIONS
6- UNPACKING THE PACKAGE
7- PRE-INSTALLATION INFORMATION
8- INSTALLATION AND USAGE
8.1- MACHINE USAGE
8.2- BURSH CLEANING
9- TABLE OF BREADING UNIT AND OPERATION
10-SPARE PART LIST
11-ELECTRICAL DIAGRAM
12-WARRANTY CERTIFICATE AND TERMS

DEAR USER,
AS MAKFRY FAMILY, WE THANK YOU FOR CHOOSING OUR DEVICE AND FOR YOUR TRUST IN OUR
COMPANY. WE IMPORTANTLY REMEMBER YOU TO READ THE INSTRUCTIONS AND INFORMATION IN
THE USER MANUAL CAREFULLY AND HAVE YOUR USERS READ IT IN ORDER TO GET THE PRODUCT
SUITABLE FOR YOUR EXPECTATIONS AND TO USE IT FOR A LONG-TERM.
THE INFORMATION REGARDING THE INSTALLATION, USAGE AND MAINTENANCE OF THE PRODUCT
YOU HAVE PURCHASED IS INCLUDED IN THE USER'S MANUAL.
PLEASE READ THE USER MANUAL CAREFULLY BEFORE INSTALLING YOUR DEVICE. THE CONNECTION
NETWORK MUST BE PREPARED BY AUTHORIZED PERSONNEL IN ACCORDANCE WITH THE LEGAL
REGULATIONS. IF THE MAINS VOLTAGE TO THE ELECTRICAL CONNECTION OF YOUR DEVICE IS NOT IN
SUITABLE CONDITIONS, THE VOLTAGE OVER THE DEVICE'S CAPACITY WILL CAUSE FAILURE AND
YOUR DEVICE WILL BE OUT OF THE SCOPE OF WARRANTY.

1- GENERAL INFORMATION
THIS USER'S MANUAL CONTAINS INFORMATION ABOUT MAKFRY PAN202 INSTRUCTIONS FOR USE,
REQUIREMENTS AND COVERAGE OF WARRANTY.
CAREFULLY READ ALL INSTRUCTIONS AND WARNINGS IN THE USER'S MANUAL. THIS USER'S
MANUAL CONTAINS IMPORTANT INFORMATION ABOUT THE SAFE INSTALLATION, USE AND
MAINTENANCE OF YOUR PRODUCT.
THE MANUFACTURER CANNOT BE RESPONSIBLE FOR DAMAGES TO HUMAN, ENVIRONMENT OR
OTHER MATERIALS ARISING FROM PRINTING OR TRANSLATION OF THE USER'S MANUAL.
INCIDENTAL DAMAGE TO YOUR PRODUCT, NEGLIGENCE, DAMAGE DUE TO FAILURE TO FOLLOW
INSTRUCTIONS AND REGULATIONS OR WRONG CONNECTIONS AND UNAUTHORIZED INTERFERENCE
TO THE PRODUCT SHALL EXCEED THE PRODUCT WARRANTY PROCESS.
KEEP THIS USER MANUAL IN AN EASY ACCESS PLACE FOR USE IF NEEDED.

2- PRODUCT INTRODUCTION
MAKFRY PAN202 BREADING UNIT IS DESIGNED TO BE USED IN INDUSTRIAL KITCHENS AND IT IS
RECOMMENDED FOR USE BY PROFESSIONAL USERS.
3- TECHNICAL SPECIFICATIONS
DIMENSION
WIDTH:1020 MM -DEPTH:800 MM –HEIGHT: 870 MM
ENERGY
220-240 V 0,18kW 50-60HZ
WEIGHT
50 KG (GROSS)
CAPACITY
5 KG IN 1 MINUTE

4- PRODUCT SCHEME

5- TRANSPORTATION AND STORAGE CONDITIONS
THE PRODUCT IS SPECIALLY PACKED AND SHIPPED IN A FORM. CARRY THE PRODUCT WITH THE
FORKLIFT FEET INSTALLED UNDER THE PALLET. IF THE TRANSPORT DISTANCE IS FAR, IT MUST BE
MOVED SLOWLY AND SUPPORTED BY AN ADDITIONAL PERSON TO AVOID LOSS OF BALANCE. DO
NOT KNOW OR DROP THE PRODUCT WHEN CARRYING IT. IF THE PRODUCT IS TO BE STORED
WITHOUT USING, IT SHOULD BE STORED WITHOUT OPENING ITS PACKAGING AND CASE. IF THE
PRODUCT IS TO BE USED AND STORED AGAIN, IT MUST BE PROTECTED BY CLEANING AND
PACKAGING
6- UNPACKING THE PACKAGE
CHECK THAT THE PRODUCT IS NOT DAMAGED DURING SHIPPING. CHECK THAT THE PARTS OF THE
PRODUCT ARRIVES COMPLETELY.
PARTS IN CONTACT WITH FOOD ARE MADE OF STAINLESS STEEL. PLASTIC PARTS IN CONTACT WITH
FOOD ARE MANUFACTURED ACCORDING TO FOOD REGULATIONS. ALL PLASTIC PARTS ARE MARKED
WITH THE MATERIAL SYMBOL.
DISPOSE THE PACKAGING MATERIALS OF THE PRODUCT AFTER INSTALLATION ACCORDING TO THE
SAFETY AND ENVIRONMENTAL CONDITIONS AND ACCORDING TO THE REGULATIONS OF THE
COUNTRY YOU ARE IN. TAKE THE RECYCLABLE MATERIAL (FOIL, CARTON, STYROFOAM, ETC.) INTO
THE RELEVANT RECYCLING BOXES. WHEN DISPOSAL OF ANY ELECTRICAL EQUIPMENT, MAKE IT
UNUSABLE BY CUTTING THE CABLE.

7- PRE-INSTALLATION INFORMATION
INSTALLATION MUST BE DONE BY AN AUTHORIZED TECHNICIAN ACCORDING TO THE INSTRUCTIONS
AND REGULATIONS. OUR COMPANY CANNOT BE LIABLE FOR ANY DAMAGES DUE TO INCORRECT
INSTALLATION.
IF THE PRODUCT FAILS, TURN OFF THE PRODUCT. ONLY A SERVICE AUTHORIZED BY THE
MANUFACTURER MUST PROVIDE THE PRODUCT.
FAULTS MUST BE REPLACED WITH ORIGINAL SPARE PARTS. THE PARTS LIST IS ALSO STATED IN THE
BOOKLET.
THE FLOOR ON THE PRODUCT MUST BE FLAT. NECESSARY PRECAUTIONS MUST BE TAKEN AGAINST
THE RISKS OF THE PRODUCT TO TURNOVER.
THE PRODUCT MUST BE CONNECTED TO THE MAIN NETWORK BY AN AUTHORIZED ELECTRICAL
TECHNICIAN ONLY IN ACCORDANCE WITH THE LAW AND REGULATIONS. MAKE SURE THAT THE
POWER FROM THE MAIN NETWORK WILL MATCH THE POWER OF THE PRODUCT. MAKE THE
GROUND CONNECTION OF THE PRODUCT ACCORDING TO THE STANDARDS AND SAFETY RULES.
GROUNDING OF THE PRODUCT MUST BE CONNECTED TO THE EARTH LINE ON THE NEAREST PANEL
OF THE ELECTRICAL INSTALLATION. THE PRODUCT ELECTRICAL CONNECTION, MAIN FUSE AND
LEAKAGE FUSE MUST COMPLY WITH THE APPLICABLE REGULATIONS AND RULES.

8- INSTALLATION AND USAGE
8.1-MACHINE USAGE
AFTER PLACING THE BREADING UNIT IN THE WORKING AREA, LOCK THE WHEELS USING THE
LOCKING MECHANISM TO PREVENT IT FROM MOVING DURING OPERATION. BEFORE PLUGGING IN
THE PANELING UNIT, MAKE SURE YOU HAVE AN ELECTRICAL INSTALLATION THAT MATCHES THE
POWER VALUES INDICATED ON THE MACHINE.
*MAKE SURE THE DISCHARGE COVER IS CLOSED AND THE SIFTED FLOUR BIN AND LUMPY FLOUR BIN
ARE IN PLACE BEFORE STARTING THE OPERATION.
1. POUR BATTER FLOUR INTO THE BATTER MILK TANK.
2. ADD WATER ACCORDING TO THE MEASURED AMOUNT YOU POURED.
3. MIX AND PREPARE YOUR BATTER MILK.
4. DIP YOUR MARINATED PRODUCT INTO THE BATTER MILK.
5. COVER ALL PRODUCTS WITH BATTER MILK.
6. REMOVE THE BATTER BASKET FROM THE BATTER MILK UNIT.
7. HANG THE BASKET ON THE BASKET HANGING ARM TO DRAIN EXCESS BATTER MILK.
8. LIFT THE DRAINED PRODUCT TO POUR IT INTO THE PANELING FLOUR.
9. POUR THE DRAINED PRODUCT INTO THE PANELING FLOUR.
10. COVER THE PRODUCTS COMPLETELY WITH PANELING FLOUR.
11. MIX THE PRODUCTS IN THE PANELING FLOUR.
12. ARRANGE THE PRODUCTS IN THE COOKING BASKET.
13. PRESS THE START BUTTON TO SIFT LUMPY FLOUR AFTER THE PANELING PROCESS IS
COMPLETED.
14. OPEN THE DISCHARGE COVER OF THE PANELING BIN.
15. DIRECT THE PANEL FLOUR TOWARDS THE SIEVE WITH THE HELP OF THE COVER.

16. POUR ALL THE PANELING FLOUR INTO THE SIEVE.
17. PRESS THE STOP BUTTON AFTER POURING ALL THE PANELING FLOUR.
18. REMOVE THE SIFTED FLOUR BIN.
19. POUR THE SIFTED FLOUR INSIDE THE SIFTED FLOUR BIN INTO THE PANELING UNIT.
20. YOU CAN REUSE THE SIFTED CLEAN FLOUR FOR THE PANELING PROCESS.

8.2-BRUSCH CLEANING
BEFORE STARTING THE OPERATION, UNPLUG YOUR MACHINE AND REMOVE THE PANELING TUB.
1- YOU WILL FIND THE BRUSH CHAMBER COVER UNDER THE TUB.
2- REMOVE THE BRUSH CHAMBER COVER.
3- HOLD THE BRUSH FROM THE LEFT SIDE AS SHOWN IN THE PICTURE.
4- PULL THE BRUSH STRONGLY TOWARDS THE RIGHT SIDE AND RELEASE IT ON THE FIXING PIN.
5- LIFT THE BRUSH UPWARDS AND REMOVE IT (IF NECESSARY, SOAK IT IN WATER) AND CLEAN
IT.
6- HOLD THE METAL MESH UNDER THE BRUSH.
7- REMOVE THE METAL MESH (IF NECESSARY, SOAK IT IN WATER) AND CLEAN IT, AND THEN
REATTACH IT.
8- MAKE SURE THAT THE MOTOR SHAFT, SHOWN IN THE PICTURE, IS CLEAN.
9- FOR BRUSH ASSEMBLY, PLACE THE BRUSH SLOT ON THE MOTOR SHAFT BEARING AND PUSH
THE BRUSH TO THE RIGHT SIDE, AND THEN FIT IT INTO THE FIXING PIN ON THE LEFT SIDE.
10-AFTER THE BRUSH IS SEATED IN THE BRUSH SLOT, TURN ON THE POWER AND TEST THE
BRUSH, AND THEN TURN OFF THE POWER. THE BRUSH WILL ROTATE IN THE DIRECTION OF
THE MILLEDGE ON THE METAL MESH.
*REVERSE THE PROCEDURE AND REATTACH THE PANELING TUB, AND CLOSE IT COMPLETELY.

9- TABLE OF BREADING UNIT AND OPERATION
9-BREADING UNIT AND PROCESS
RAW MATERIAL
PREPARATION
BATTERMILK
1.5 MEASURES OF WATER IS ADDED TO BATTERMILK 1
MEASUREMENT BREADING FLOUR AND IT IS READY TO USE
BY WHIPPING
BREADING FLOUR
READY TO USE
BREADING PROCESS
PRODUCT
STEP 1
STEP 2
STEP 3
STEP 4
STEP 5
BONELESS
CHICKEN
PIECES,
HOTWINGS,
STRIPS
BEAT THE
BATTERMILK
APPLY THE
BATTERMILK TO
CHICKEN BREAST,
PIECES
COVER THE CHIKEN
PIECES WITH BREADING
FLOUR
WHILE HOLDING CHICKEN
PIECES WITH YOUR FINGERS,
FLASH THE EXCESS FLOUR BY
STRIKING YOUR PALM 3 TIMES
PLACE THE
CHICKEN PARTS
IN YOUR BASKET
BONE CHICKEN
PIECES
MIX THE
BATTERMILK
APPLY THE
BATTERMILK TO
CHICKEN PIECES
COVER THE CHIKEN
PIECES WITH BREADING
FLOUR
WHILE HOLDING CHICKEN
PIECES WITH YOUR FINGERS,
FLASH THE EXCESS FLOUR BY
STRIKING YOUR PALM 3 TIMES
PLACE THE
CHICKEN PARTS
IN YOUR BASKET
FLOUR SIEVING PROCESS
STEP 1
STEP 2
STEP 3
STEP 4
REMOVE THE LID AND
THROW THE FLOUR INSIDE
OF THE MACHINE
PRESS THE START BUTTON
REPLACE THE LID
TAKE THE RESIEVED CONTAINER AND
REUSE

10-SPARE PART LIST
1
START BUTTON
14
DRAIN CONTAINER COVER
2
STOP BUTTON
15
CONTACTOR
3
EMERGENCY STOP BUTTON
16
THERMAL RELAY
4
PAN202 WHEEL WITH BRAKE
17
5
PAN202 WHEEL WITHOUT BRAKE
18
6
BATTER BASKET
19
7
BATTER CONTAINER
20
8
BREADING CONTAINER
21
9
SIEVED FLOUR CONTAINER
22
10
WASTE FLOUR CONTAINER
23
11
GRINDING BRUSH
24
12
ELECTROC MOTOR 0,18 KW
25
13
REDUCER NMRV 03- 30D/DK
26

11-ELECTRICAL DIAGRAM

12-WARRANTY CERTIFICATE AND TERMS
AS MAKFRY FAMILY, THANK YOU FOR CHOOSING OUR PRODUCTS. WARRANTY DOCUMENT MUST BE KEPT
DURING THE WARRANTY PROCESS. IF THE DOCUMENT IS LOST, A SECOND DOCUMENT WILL NOT BE GIVEN TO
THE CUSTOMER AND THIS DOCUMENT MUST BE SHOWED WHEN THE CUSTOMER REQUIRES WARRANTY
REPAIR. OTHERWISE, REPAIR IS CHARGED. IF THE WARRANTY DOCUMENT IS UNCLEAR, MAKFRY MAY ALSO
REQUEST A CERTIFICATE OF PURCHASE.
1- THE WARRANTY PROCESS STARTS FROM DELIVERY DATE TO THE CONSUMER AND IS 2 YEARS. DIGITAL
PANEL IS 1 YEAR, RESISTANCES ARE 6 MONTHS.
2- IF THE GOODS FAILS WITHIN THE WARRANTY PERIOD, THE PERIOD IN REPAIR IS ADDED TO THE
WARRANTY PERIOD. THE REPAIR TIME OF THE GOODS IS A MAXIMUM 30 BUSINESS DAYS.
3- MAINTENANCE AND REPAIR MUST BE DONE BY AUTHORIZED BY MAKFRY. OTHER INTERVENTIONS,
THE GOODS WILL BE OUT OF THE SCOPE OF WARRANTY.
4- IF DEFECTIVE MATERIAL AND/OR WORKMANSHIP CAUSES FAILURE DURING THE WARRANTY PERIOD,
MAKFRY WILL MAKE THE NECESSARY ARRANGEMENTS AT ITS OWN EXPENSE, AND ITS ANY DAMAGES
UNDER THE SCOPE OF THE WARRANTY.
5- WARRANTY DOES NOT COVER CONSEQUENTIAL DAMAGES, INCLUDING LOSS OF BUSINESS OR
INFORMATION, AND DOES NOT APPLY TO THE FOLLOWING CASES:
• IF THE GOODS IS USED AGAINST THE METHODS OR CONDITIONS STATED IN THE PROMOTION AND
USER'S GUIDE OR APPENDIX,
• IF IT IS DETERMINED THAT THE GOODS WAS PREVIOUSLY REPAIRED OR OPENED BY NON-
AUTHORIZED PERSONS AND/OR REPAIR WORKSHOPS,
• IF THE GOOD IS USED WITH UNAPPROPRIATE VOLTAGE OR WITH FAULTY ELECTRICAL INSTALLATION
WITHOUT THE KNOWLEDGE OF AUTHORIZED SERVICES DETERMINED BY MAKFRY.

• IF THE SERIAL NUMBER OF THE GOODS IS DAMAGED OR DISASSEMBLED, ANY MODIFICATION IS
MADE TO THE WARRANTY DOCUMENT OR PURCHASE DOCUMENTS, OR THE DOCUMENTS HAVE BEEN
ILLEGAL,
• IF FAULT OR DAMAGE OCCURRED DURING SHIPPING, WHICH IS NOT MAKFRY'S RESPONSIBILITY,
• IF THE EXTERIOR SURFACES OF THE GOODS ARE DAMAGED WITHIN THE CONSUMER
RESPONSIBILITY,
• IN CASE OF FAULTS CAUSED BY ACCESSORIES OR OTHER DEVICES THAT CAN BE USED WITH THE
PRODUCT AND PURCHASED FROM A PLACE OUTSIDE OF OUR COMPANY OR OUR AUTHORIZED
SERVICES,
• IN CASE OF FAILURES AND DAMAGES CAUSED BY NATURAL DISASTERS SUCH AS FIRE, LIGHTNING,
FLOOD, EARTHQUAKE ETC,
• IF THE ELECTRONIC PARTS OF THE GOODS ARE DAMAGED DUE TO LIQUID CONTACT WITH THE
CONSUMER'S RESPONSIBILITY,
• THE WARRANTY DOES NOT COVER ANY WEAR PRODUCTS AND/OR PRODUCT PARTS MADE OF
ACCESSORIES OR GLASS, WHICH CAN BE CONSIDERED AS CONSUMABLES BY NATURE,
• IF THE FAILURE IS CAUSED BY ERRORS OR MISUSE OF THE PRODUCT OR ENVIRONMENTAL
CONDITIONS THAT DO NOT FOLLOW THE RECOMMENDED CONDITIONS OF USE OF THE PRODUCT,
• THE WARRANTY IS FOR CORROSION, DEFORMATIONS AND DAMAGES OCCURING IN ESPECIALLY
ELECTRICAL COMPONENTS ARISING FROM OPERATION OF THE DEVICE IN ACIDIC OR HUMID
ENVIRONMENTS.
• IN TSE OR CE CERTIFIED PRODUCTS USED, EXCEPT MAKFRY SPECIAL PRODUCTION ON THE GOODS.
6- TRANSPORTATION COSTS OF MAKFRY AUTHORIZED SERVICE PERSONNEL IN THE REPAIR PROCESS TO
BE DONE WHERE THE GOODS ARE AVAILABLE, WITH ON-SITE SERVICE. ACCORDING TO THE
AUTHORIZED SERVICE DETECTION, THE REPLACEMENT/REPAIR OF THE WARRANTY WILL BE MADE
WITH OR FREE OF CHARGE.
7- İZMİR COURTS AND EXECUTION OFFICES ARE AUTHORIZED IN CASE OF CONFLICT OF SCOPE OF
WARRANTY.

MODEL
SERIAL NUMBER
WARRANTY PERIOD
WARRANTY PROCESS START
ADDRESS: GÖKDERE CADDESİ NO:27/A STAMP - SIGNATURE
35040 - GÖKDERE / BORNOVA/ İZMİR
CONTACT: [phone]
E-MAIL: [e-mail]