MAKINEX Jackhammer Trolley Installation and operating manual

Operation and Safety Guide
Tile Smasher Attachment for
MAKINEX Jackhammer Trolley
Created by: Michael Chen Revision Level: 2
Company: Makinex Revision Date: 10/04/15
SAFETY TOPICS:
Read and understand the operator’s
Manual, or “Operations and Safety Guide”
before using this machine. Failure to
follow operating instructions could
result in death or serious injury.
SAFETY CHECKLIST:
ALWAYS wear safety goggles, ear
protection and hard toe shoes when
operating with this equipment.
ALWAYS ensure machine is switched OFF
before plugging in.
ALWAYS ensure the Tile Smasher Head is
correctly inserted and positioned before
use.
ALWAYS inspect the Jackhammer Trolley
for any signs of damage before use.
do not use if it appears damaged.
DO NOT wear loose clothing while
operating this machine. Loose material
may become caught in the mechanism.
DO NOT touch the Tile Smasher Head
whilst the machine is in operation.
DO NOT operate if you have a known
medical condition which may affect your
ability to safety operate the Jackhammer
Trolley.
DO NOT use as a levering device
ALWAYS maintain a correct stance while
operating the Jackhammer Trolley to avoid
injury.
ALWAYS use on a flat, level surface.
ALWAYS use a dedicated power supply
with an extension cord that does not
exceed 30 feet in length.
ALWAYS switch OFF the machine before
unplugging.
Tool Application: The MAKINEX Jackhammer Trolley Tile Smasher
attachment is used for lifting and removing tiles from wooden and concrete
surfaces and for cleaning tile beds. It can also be used for removing vinyl and cork
flooring.
Tool Setup:
Step
Action
1
Lean the Jackhammer Trolley on its back with the hammer facing
up to get a comfortable working position, then insert the shank into
the hammer (A).
2
Position the Tile Smasher Head horizontally and gently tap onto the
shank so it will not fall off (B).
3
Position the Jackhammer Trolley upright and check if the entire
front edge of the blade on Tile Smasher Head is flush against the
ground (C).
4
Once that is confirmed, tap the Tile Smasher Head firmly onto the
shank and then return to upright position (D).
Tool Operation:
Step
Action
1
Ensure Tile Smasher is mounted correctly and the jackhammer is
properly secured in the clamping mechanism of the trolley and
cannot rotate.
2
Never allow Jackhammer or Tile Smasher to overheat. (Refer to
Jack Hammer manufacturer for continuous usage guidelines).
Take regular breaks to avoid user fatigue and wear on hammer.
3
Turn on the power switch of the Jackhammer.
4
Place both hands on handle and place a foot on the footrest,
adjust to a desired angle.
5
Maintain a straight back and proceed in a slow, steady linear
motion while operating the Jackhammer Trolley (E).
(C)
Vendor Website: www.makinexusa.com Makinex USA Support #: 407-446-1966, 407-826-0000
Forward
motion
A
B
C
D
E

Revision 1 10/04/15
Tool Inspection Process:
Step
Action
1
Visually check for dents/cracks as well as broken, missing or worn parts.
2
Check to ensure all bolts are secure and tightened or replace them if necessary (specific torque rating needs to be applied).
3
Check Blade is correctly assembled and sits flush against the back of the Tile Smasher Head, adjust or replace if needed.
4
Check there is nothing obstructing the tapered hole where the shank is to be fitted.
Tool Cleaning & Maintenance Process:
Step
Action
1
Use compressed air to blow off excess dirt / dust.
2
Clean off any grease or surface grit.
3
To replace worn blades/bolts, use an impact gun (A).
4
Set the torque wrench to 64lb/ft and apply to all three bolts after screwing them in place (B).
5
Wipe of Wipe off tool with clean dry rag.
TILE SMASHER HEAD (TSH)
MAINTENANCE GUIDE
Supplier Support #: US Only: 407-446-1966,
407-826-0000
Supplier Website: www.makinexusa.com
PURPOSE
Follow the directions below to ensure that the Tile Smasher Head is in working order and properly
maintained.
SAFETY
Always wear approved eye and ear protection when working with air tools.
DO NOT USE if parts are faulty.
(A)
(B)