Makita DC10SB User manual

Symbols
The followings show the symbols used for the equipment. Be sure that you understand their meaning before use.
• Indoor use only. • Read instruction manual.
• DOUBLE INSULATION • Ready to charge.
• Charging. • Charging complete.
• Delay charge (Battery cooling, or
too cold battery). • Defective battery.
• Delay charge (Too hot or too cold
battery). • Cooling abnormality.
• Do not short battery. • Do not destroy battery by re.
• Do not expose battery to water or
rain. • Always recycle battery.
Specication:
Model DC10SB DC10WD
Input A.C. 120 V 50 – 60 HZ
Output D.C. 10.8 V – D.C. 12 V (max.)
Weight 0.63 kg (1.5 lbs) 0.35 kg (0.77 lbs)
• Due to our continuing program of research and development, the specications herein are subject to change without
notice.
• Specications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
IMPORTANT SAFETY INSTRUCTIONS
CAUTION:
1.
SAVE THESE
INSTRUCTIONS
– This manual contains important safety and
operating instructions for battery charger.
2. Before using battery charger, read all instructions
and cautionary markings on (1) battery charger, (2)
battery, and (3) product using battery.
3. CAUTION – To reduce risk of injury, charge only
Makita type rechargeable batteries. Other types
of batteries may burst causing personal injury and
damage.
4. Non-rechargeable batteries cannot be charged with
this battery charger.
5. Use a power source with the voltage specied on the
nameplate of the charger.
6. Do not charge the battery cartridge in presence of
ammable liquids or gases.
7. Do not expose charger to rain or snow.
8. Never carry charger by cord or yank it to disconnect
from receptacle.
9. After charging or before attempting any maintenance
or cleaning, unplug the charger from the power
source. Pull by plug rather than cord whenever
disconnecting charger.
10. Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected to
damage or stress.
11. Do not operate charger with damaged cord or plug. If
the cord or plug is damaged, ask Makita authorized
service center to replace it in order to avoid a hazard.
12. Do not operate or disassemble charger if it has
received a sharp blow, been dropped, or otherwise
damaged in any way; take it to a qualied
serviceman. Incorrect use or reassembly may result
in a risk of electric shock or re.
13. The battery charger is not intended for use by young
children or inrm persons without supervision.
14. Young children should be supervised to ensure that
they do not play with the battery charger.
15. Do not charge battery cartridge when room
temperature is BELOW 10°C (50°F) or ABOVE 40°C
(104°F). At the cold temperature, charging may not
start.
16. Do not attempt to use a step-up transformer, an
engine generator or DC power receptacle.
17. Do not allow anything to cover or clog the charger
vents.
DC10SB
DC10WD
IMPORTANT: Read Before Using.

NOTE:
• The battery charger is for charging Makita-battery
cartridge. Never use it for other purposes or for other
manufacturer’s batteries.
• If charging light may ash in red color, battery condition
is as below and charging may not start.
– Battery cartridge from just-operated tool or battery
cartridge that has been left in a location exposed to
direct sunlight for a long time.
– Battery cartridge that has been left for a long time in a
location exposed to cold air.
When the battery cartridge is too hot, charging does not
begin until the battery cartridge temperature reaches
the degree at which charging is possible.
• If the charging light ashes alternately in green and red
color, charging is not possible. The terminals on the
charger or battery cartridge are clogged with dust or the
battery cartridge is worn out or damaged.
Cooling system (only for DC10SB)
• This charger is equipped with cooling fan for heated
battery in order to enable the battery to prove its own
performance. Sound of cooling air comes out during
cooling, which means no trouble on the charger.
• Yellow light will ash for warning in the following cases.
– Trouble on cooling fan
– Incomplete cool down of battery, such as, being
clogged with dust
The battery can be charged in spite of the yellow
warning light. But the charging time will be longer than
usual in this case. Check the sound of cooling fan, vent
on the charger and battery, which can be sometime
clogged with dust.
• The cooling system is in order although no sound of
cooling fan comes out, if the yellow warning light will
not ash.
• Always keep clean the vent on charger and battery for
cooling.
• The products should be sent to repair or maintenance, if
the yellow warning light will frequently ash.
Charging
1. Plug the battery charger into the proper AC voltage
source. Charging light will ash in green color
repeatedly.
2. Insert the battery cartridge into charger until it stops
adjusting to the guide of charger.
3. When the battery cartridge is inserted, the
charging light color will change from green to red
and charging will begin. The charging light will
keep lighting up steadily during charging. One red
charging light indicates charged condition in 0 –
80% and red and green ones indicate 80 – 100%.
The 80% indication mentioned above is approximate
value. The indication may differ according to battery
temperature or battery condition.
4. With nish of charge, the charging lights will change
from red and green ones to green one.
5. Charging time varies by temperature (10°C (50°F)
– 40°C (104°F)) that battery cartridge is charged at
and conditions of the battery cartridge, such as a
battery cartridge which is new or has not been used
for a long period of time.
6. After charging, remove the battery cartridge from
charger and unplug the charger.
Voltage 10.8 V – 12 V (max.) Charging time (Minutes)
Number of cells 3 DC10SB DC10WD
Li-ion Battery
cartridge
BL1016 22 50
BL1021B 30 70
BL1041B 60 130

Wall mounting
Warning:
• Make sure to use two screws for hanging the charger
on the wall, and anchor the charger on the wall with
another screw.
Otherwise the charger may fall and cause serious injury.
• Always be sure that the charger is unplugged and all
the batteries are removed from the charger before
performing wall mounting work.
• Follow the steps instructed in this manual, and complete
the whole procedures at once. The charger may fall and
cause injury or damage if you stop the work in the half
way.
• Check tightness of the screws on regular basis.
Otherwise the charger may fall because of loosen
screw.
• Clean the terminal parts of the charger on regular basis
with an air duster etc.
Caution:
• Carefully choose a stable wall for mounting the charger.
Make sure there is no hindrance to mounting work or
charging operation. The gross weight of the charger
and battery reach approximately 1.1 kg (2.43lbs)
(DC10SB) / 0.8 kg (1.76lbs) (DC10WD), provide
sufcient reinforcement for the wall if necessary.
Things you need to prepare:
– Two screws - for hanging the charger.
Screw size : 4mm x more than 20mm
(5/32” x more than 13/16”).
Screw head size : ø9.0mm or less and less than
3.5mm thickness.
(ø11/32” x 1/8”).
– One screw (4mm (5/32”) x more than 25mm (1”)) - for
anchoring the charger.
– One more screw (only for DC10SB) (4mm (5/32”) x
more than 40mm (1-9/16”)) - for supporting the
charger.
– Tools - for tightening screws.
You can mount the charger on the wall either horizontal or
vertical direction. (Fig. 1&2)
1. Fix the two screws for hanging on the wall as
illustrated. (Fig. 3)
2. Hang the charger with the screws xed in step 1.
3. Mount the charger on the wall by tightening the
anchor screw completely. (Fig. 4)
(For DC10SB it is needed one more screw for
supporting the charger on the wall.)

2
(DC10SB)
≧32mm
(1-9/32”)
≧50mm
(1-31/32”)
≧75mm
(2-31/32”)
≧115mm
(4-17/32”)
110mm
(4-11/32”)
≧30mm
(1-3/16”)
≧30mm
(1-3/16”)
≈8mm
(5/16”)
≧180mm
(7-3/32”)
69mm
(2-23/32”)
≧90mm
(3-9/16”)
(DC10WD)
≧30mm
(1-3/16”)
≧40mm
(1-19/32”)
≧50mm
(1-31/32”)
≧105mm
(4-5/32”)
≧65mm
(2-9/16”)
113mm
(4-15/32”)
≧55mm
(2-3/16”)
≧35mm
(1-3/8”)
≈4mm
(5/32”)
113mm
(4-15/32”)
≧115mm
(4-17/32”)
1
2
3 4

INSTRUCTION MANUAL
Cordless Driver Drill
FD05
FD06
IMPORTANT: Read Before Using.

SPECIFICATIONS
Model: FD05 FD06
Drilling capacities Steel 10 mm (3/8")
Wood 21 mm (13/16")
Fastening
capacities
Wood screw 5.1 mm x 63 mm (7/32" x 2-1/2")
Machine screw M6 (1/4")
No load speed
(RPM)
High (2) 0 - 1,700 /min
Low (1) 0 - 450 /min
Overall length 189 mm (7-7/16") 157 mm (6-3/16")
Rated voltage D.C. 10.8 V - 12 V max
Standard battery cartridge BL1016, BL1021B BL1041B BL1016, BL1021B BL1041B
Net weight 1.1 kg (2.4 lbs) 1.3 kg (2.8 lbs) 0.94 kg (2.1 lbs) 1.1 kg (2.4 lbs)
• Duetoourcontinuingprogramofresearchanddevelopment,thespecicationshereinaresubjecttochange
without notice.
• Specicationsandbatterycartridgemaydifferfromcountrytocountry.
•Weight, with battery cartridge, according to EPTA-Procedure 01/2003
General power tool safety warnings
WARNING: Read all safety warnings and
all instructions. Failure to follow the warnings and
instructionsmayresultinelectricshock,reand/or
seriousinjury.
Save all warnings and instruc-
tions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
1. Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
2. Do not operate power tools in explosive atmo-
spheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
3. Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
Electrical Safety
1. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodiedplugsandmatchingoutletswill
reduce risk of electric shock.
2. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of elec-
tric shock if your body is earthed or grounded.
3. Do not expose power tools to rain or wet con-
ditions. Water entering a power tool will increase
the risk of electric shock.
4. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
5. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
6. If operating a power tool in a damp location is
unavoidable, use a ground fault circuit inter-
rupter (GFCI) protected supply. Use of a GFCI
reduces the risk of electric shock.
Personal Safety
1. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the inuence of drugs, alcohol or med-
ication. A moment of inattention while operating
powertoolsmayresultinseriouspersonalinjury.
2. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
willreducepersonalinjuries.
3. Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
yourngerontheswitchorenergisingpowertools
that have the switch on invites accidents.
4. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
resultinpersonalinjury.
5. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
6. Dress properly. Do not wear loose clothing
or jewellery. Keep your hair, clothing, and
gloves away from moving parts. Loose clothes,

jewelleryorlonghaircanbecaughtinmoving
parts.
7. If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
Power tool use and care
1. Do not force the power tool. Use the correct
power tool for your application. The correct
powertoolwilldothejobbetterandsaferatthe
rate for which it was designed.
2. Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.
3. Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such pre-
ventive safety measures reduce the risk of starting
the power tool accidentally.
4. Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
5. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
6. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
7. Use the power tool, accessories and tool bits
etc. in accordance with these instructions, tak-
ing into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended could
result in a hazardous situation.
Battery tool use and care
1. Recharge only with the charger specied by
the manufacturer. A charger that is suitable for
onetypeofbatterypackmaycreateariskofre
when used with another battery pack.
2. Use power tools only with specically desig-
nated battery packs. Use of any other battery
packsmaycreateariskofinjuryandre.
3. When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from one
terminal to another. Shorting the battery termi-
nalstogethermaycauseburnsorare.
4. Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If con-
tact accidentally occurs, ush with water. If
liquid contacts eyes, additionally seek medical
help.Liquidejectedfromthebatterymaycause
irritation or burns.
Service
1. Have your power tool serviced by a qualied
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
2. Follow instruction for lubricating and chang-
ing accessories.
3. Keep handles dry, clean and free from oil and
grease.
Cordless driver drill safety warnings
1. Use auxiliary handle(s), if supplied with the
tool.Lossofcontrolcancausepersonalinjury.
2. Hold power tool by insulated gripping sur-
faces, when performing an operation where
the cutting accessory may contact hidden
wiring. Cutting accessory contacting a "live"
wire may make exposed metal parts of the power
tool "live" and could give the operator an electric
shock.
3. Hold power tool by insulated gripping sur-
faces, when performing an operation where
the fastener may contact hidden wiring.
Fasteners contacting a "live" wire may make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.
4. Always be sure you have a rm footing. Be
sure no one is below when using the tool in
high locations.
5. Hold the tool rmly.
6. Keep hands away from rotating parts.
7. Do not leave the tool running. Operate the tool
only when hand-held.
8. Do not touch the drill bit or the workpiece
immediately after operation; they may be
extremely hot and could burn your skin.
9. Some material contains chemicals which may
be toxic. Take caution to prevent dust inhala-
tion and skin contact. Follow material supplier
safety data.
SAVE THESE INSTRUCTIONS.
WARNING: DO NOT let comfort or familiarity
with product (gained from repeated use) replace
strict adherence to safety rules for the subject
product. MISUSE or failure to follow the safety
rules stated in this instruction manual may cause
serious personal injury.
Symbols
The followings show the symbols used for tool.
volts
direct current
no load speed
revolutions or reciprocation per minute

Important safety instructions for
battery cartridge
1. Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using
battery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4. If electrolyte gets into your eyes, rinse them
out with clear water and seek medical atten-
tion right away. It may result in loss of your
eyesight.
5. Do not short the battery cartridge:
(1) Do not touch the terminals with any con-
ductive material.
(2) Avoid storing battery cartridge in a con-
tainer with other metal objects such as
nails, coins, etc.
(3) Do not expose battery cartridge to water
or rain.
A battery short can cause a large current
ow, overheating, possible burns and even a
breakdown.
6. Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50 °C (122 °F).
7. Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a re.
8. Be careful not to drop or strike battery.
9. Do not use a damaged battery.
10. Follow your local regulations relating to dis-
posal of battery.
SAVE THESE INSTRUCTIONS.
CAUTION: Only use genuine Makita batteries.
Use of non-genuine Makita batteries, or batteries that
have been altered, may result in the battery bursting
causingres,personalinjuryanddamage.Itwill
also void the Makita warranty for the Makita tool and
charger.
Tips for maintaining maximum
battery life
1. Charge the battery cartridge before completely
discharged. Always stop tool operation and
charge the battery cartridge when you notice
less tool power.
2. Never recharge a fully charged battery car-
tridge. Overcharging shortens the battery
service life.
3. Charge the battery cartridge with room tem-
perature at 10 °C - 40 °C (50 °F - 104 °F). Let
a hot battery cartridge cool down before
charging it.
FUNCTIONAL
DESCRIPTION
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before adjusting or checking function on the tool.
Installing or removing battery
cartridge
CAUTION: Always switch off the tool before
installing or removing of the battery cartridge.
CAUTION: Hold the tool and the battery car-
tridge rmly when installing or removing battery
cartridge. Failure to hold the tool and the battery
cartridgermlymaycausethemtoslipoffyourhands
and result in damage to the tool and battery cartridge
andapersonalinjury.
1
2
3
1. Red indicator 2. Button 3. Battery cartridge
To remove the battery cartridge, slide it from the tool
while sliding the button on the front of the cartridge.
To install the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Insert it all the way until it locks in place
with a little click. If you can see the red indicator on the
upper side of the button, it is not locked completely.
CAUTION: Always install the battery cartridge
fully until the red indicator cannot be seen. If not,
itmayaccidentallyfalloutofthetool,causinginjuryto
you or someone around you.
CAUTION: Do not install the battery cartridge
forcibly. If the cartridge does not slide in easily, it is
not being inserted correctly.
Battery protection system
The tool is equipped with a battery protection system.
This system automatically cuts off power to the motor to
extend battery life.
The tool will automatically stop during operation if the
tool and/or battery are placed under one of the following
conditions:

Overloaded:
The tool is operated in a manner that causes it to draw
an abnormally high current.
In this situation, release the switch trigger on the tool
and stop the application that caused the tool to become
overloaded. Then pull the switch trigger again to restart.
If the tool does not start, the battery is overheated.
In this situation, let the battery cool before pulling the
switch trigger again.
Low battery voltage:
The remaining battery capacity is too low and the tool
will not operate. If you pull the switch trigger, the motor
runs again but stops soon. In this situation, remove and
recharge the battery.
Indicating the remaining battery
capacity
Only for battery cartridges with "B" at the end of the
model number
1
2
1. Indicator lamps 2. Check button
Press the check button on the battery cartridge to indi-
cate the remaining battery capacity. The indicator lamps
light up for few seconds.
Indicator lamps Remaining
capacity
Lighted Off
75% to 100%
50% to 75%
25% to 50%
0% to 25%
NOTE: Depending on the conditions of use and the
ambient temperature, the indication may differ slightly
from the actual capacity.
Switch action
1
1. Switch trigger
CAUTION: Before inserting the battery car-
tridge into the tool, always check to see that the
switch trigger actuates properly and returns to
the "OFF" position when released.
To start the tool, simply pull the switch trigger. Tool
speed is increased by increasing pressure on the switch
trigger. Release the switch trigger to stop.
Electric brake
This tool is equipped with an electric brake. If the tool
consistently fails to quickly stop after the switch trigger
is released, have the tool serviced at a Makita service
center.
Lighting up the front lamp
1
1. Lamp
CAUTION: Do not look in the light or see the
source of light directly.
Pull the switch trigger to light up the lamp. The lamp
keeps on lighting while the switch trigger is being pulled.
The lamp goes out approximately 10 seconds after
releasing the switch trigger.
NOTE: Use a dry cloth to wipe the dirt off the lens of
the lamp. Be careful not to scratch the lens of lamp, or
it may lower the illumination.

Reversing switch action
1
AB
1. Reversing switch lever
CAUTION: Always check the direction of
rotation before operation.
CAUTION: Use the reversing switch only after
the tool comes to a complete stop. Changing the
direction of rotation before the tool stops may dam-
age the tool.
CAUTION: When not operating the tool,
always set the reversing switch lever to the neu-
tral position.
This tool has a reversing switch to change the direction
of rotation. Depress the reversing switch lever from the
A side for clockwise rotation or from the B side for coun-
terclockwise rotation.
When the reversing switch lever is in the neutral posi-
tion, the switch trigger cannot be pulled.
Speed change
1
1. Speed change lever
CAUTION: Always set the speed change lever
fully to the correct position. If you operate the tool with
the speed change lever positioned halfway between the
"1" side and "2" side, the tool may be damaged.
CAUTION: Do not use the speed change lever
while the tool is running. The tool may be damaged.
Position of
speed
change lever
Speed Torque Applicable
operation
1Low High Heavy load-
ing operation
2High Low Light loading
operation
Tochangethespeed,switchoffthetoolrst.Select
the "2" side for high speed or "1" for low speed but high
torque. Be sure that the speed change lever is set to the
correct position before operation.
If the tool speed is coming down extremely during the operation
with "2", slide the lever to the "1" and restart the operation.
Adjusting the fastening torque
3
1
2
1.Adjustingring 2.Graduation 3.Arrow
Thefasteningtorquecanbeadjustedin19stepsbyturningtheadjustingring.Alignthegraduationswiththearrow
on the tool body. You can get the minimum fastening torque at 1 and maximum torque at marking.
The clutch will slip at various torque levels when set at the number 1 to 18. The clutch does not work at
the marking.
Before actual operation, drive a trial screw into your material or a piece of duplicate material to determine which
torque level is required for a particular application.
The following shows the rough guide of the relationship between the screw size and graduation.

Graduation 12345678910 11 12 13 14 15 16 17 18
Machine screw M4 M5 M6
Wood
screw
Soft wood
(e.g. pine)
–ɸ3.5 x 22 ɸ4.1x 38
Hard wood
(e.g. lauan)
–ɸ3.5 x 22 –
–ɸ4.1x 38
ASSEMBLY
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Installing or removing driver bit/
drill bit
For Model FD05 (optional accessory)
13
2
1. Sleeve 2. Close 3. Open
Turn the sleeve counterclockwise to open the chuck
jaws.Placethedriverbit/drillbitinthechuckasfar
as it will go. Turn the sleeve clockwise to tighten the
chuck. To remove the driver bit/drill bit, turn the sleeve
counterclockwise.
Installing or removing driver bit/
socket bit
For Model FD06 (optional accessory)
12 mm
(15/32”)
9 mm
(3/8”)
Useonlythedriverbit/socketbitshowninthegure.Do
not use any other driver bit/socket bit.
1
2
1. Driver bit 2. Sleeve
To install the driver bit, pull the sleeve in the direction of
the arrow and insert the driver bit into the sleeve as far
as it will go.
Then release the sleeve to secure the driver bit.
To remove the driver bit, pull the sleeve in the direction
of the arrow and pull the driver bit out.
NOTE: If the driver bit is not inserted deep enough
into the sleeve, the sleeve will not return to its original
position and the driver bit will not be secured. In this
case, try re-inserting the bit according to the instruc-
tions above.
NOTE: After inserting the driver bit, make sure that it
isrmlysecured.Ifitcomesout,donotuseit.
Installing hook
1
3
2
1. Groove 2. Hook 3. Screw
The hook is convenient for temporarily hanging the tool.
This can be installed on either side of the tool. To install
the hook, insert it into a groove in the tool housing on
either side and then secure it with a screw. To remove,
loosen the screw and then take it out.

Installing driver bit holder
Optional accessory
1
2
1. Driver bit holder 2. Driver bit
Fit the driver bit holder into the protrusion at the tool foot
on either right or left side and secure it with a screw.
When not using the driver bit, keep it in the driver bit
holders. Driver bits 45 mm-long (1-3/4") can be kept
there.
OPERATION
CAUTION: Always insert the battery cartridge
all the way until it locks in place. If you can see
the red part on the upper side of the button, it is not
locked completely. Insert it fully until the red part can-
not be seen. If not, it may accidentally fall out of the
tool,causinginjurytoyouorsomeonearoundyou.
CAUTION: When the speed comes down
extremely, reduce the load or stop the tool to
avoid the tool damage.
Holdthetoolrmlywithonehandonthegripandthe
other hand on the bottom of the battery cartridge to
control the twisting action.
Screwdriving operation
CAUTION: Adjust the adjusting ring to the
proper torque level for your work.
CAUTION: Make sure that the driver bit is
inserted straight in the screw head, or the screw
and/or driver bit may be damaged.
Place the point of the driver bit in the screw head and
apply pressure to the tool. Start the tool slowly and then
increase the speed gradually. Release the switch trigger
as soon as the clutch cuts in.
NOTE: When driving wood screw, pre-drill a pilot hole
2/3 the diameter of the screw. It makes driving easier
and prevents splitting of the workpiece.
Drilling operation
First,turntheadjustingringsothatthepointerpointsto
the marking. Then proceed as follows.
Drilling in wood
When drilling in wood, the best results are obtained
with wood drills equipped with a guide screw. The guide
screw makes drilling easier by pulling the drill bit into
the workpiece.
Drilling in metal
To prevent the drill bit from slipping when starting a
hole, make an indentation with a center-punch and
hammer at the point to be drilled. Place the point of the
drill bit in the indentation and start drilling.
Use a cutting lubricant when drilling metals. The excep-
tions are iron and brass which should be drilled dry.
CAUTION: Pressing excessively on the tool
will not speed up the drilling. In fact, this excessive
pressure will only serve to damage the tip of your drill
bit, decrease the tool performance and shorten the
service life of the tool.
CAUTION: Hold the tool rmly and exert care
when the drill bit begins to break through the
workpiece. There is a tremendous force exerted on
the tool/drill bit at the time of hole break through.
CAUTION: A stuck drill bit can be removed
simply by setting the reversing switch to reverse
rotation in order to back out. However, the tool
may back out abruptly if you do not hold it rmly.
CAUTION: Always secure small workpieces
in a vise or similar hold-down device.
CAUTION: If the tool is operated continuously
until the battery cartridge has discharged, allow
the tool to rest for 15 minutes before proceeding
with a fresh battery.

Using the tool as a hand screwdriver
Switch off the tool.
Move the reversing switch lever to the neutral position.
Turntheadjustingringsothatthearrowpointsto
the marking.
Turn the tool.
NOTE: This use is convenient for checking the
screwdriving.
NOTE: Do not use the tool for work requiring exces-
sive force, such as tightening bolt or removing rusted
screws.
Using holster
Optional accessory
CAUTION: When using the holster, remove a
driver bit/drill bit from the tool.
CAUTION: Turn off the tool and wait until it
comes to a complete stop before placing it in the
holster.
Be sure to close the holster securely with the
holster button so that it holds the tool rmly.
1. Thread a waist belt or similar through holster
holder.
1
2
1. Holster holder 2. Waist belt
2. Put the tool in the holster and lock it with the hol-
ster button.
You can keep two driver bits at the front of the holster.
MAINTENANCE
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
NOTICE: Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,
repairs,anyothermaintenanceoradjustmentshould
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
OPTIONAL
ACCESSORIES
CAUTION: These accessories or attachments
are recommended for use with your Makita tool
specied in this manual. The use of any other
accessories or attachments might present a risk of
injurytopersons.Onlyuseaccessoryorattachment
for its stated purpose.
If you need any assistance for more details regard-
ing these accessories, ask your local Makita Service
Center.

• Drill bits
• Driver bits
• Socket bits
• Bit piece
• Driver bit holder
• Holster
• Plastic carrying case
• Hook
• Makita genuine battery and charger
NOTE: Some items in the list may be included in the
tool package as standard accessories. They may
differ from country to country.

Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to the State of California
to cause cancer, birth defects or other reproductive harm. Some examples
of these chemicals are:
• lead from lead-based paints,
•crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this
type of work. To reduce your exposure to these ch emicals: work in a well
ventilated area, and work with approved safety equipment, such as those
dust masks that are specially designed to filter out microscopic particles.
WARNING
< USA only >

GB Cordless LED
Flashlight Instruction manual
FLampe Torche LED Manuel
d’instructions
ELinterna LED
Inalámbrica
Manual de
instrucciones
ML103
A
1
2
3
4
B
5
67
ENGLISH
SPECIFICATIONS
Model ML103
Voltage D.C. 10.8 V -
12 V max
LED 1.5 W
Operating time
with BL1016 Approx. 11 hours
with BL1021B Approx. 14 hours
with BL1041B Approx. 28 hours
Dimentions
without battery
77 mm x 54 mm x
28 mm
(3″ x 2-1/8″ x 1-1/8″)
with BL1016/BL1021B
87 mm x 64 mm x
54 mm
(3-7/16″ x 2-1/2″ x
2-1/8″)
with BL1041B
87 mm x 64 mm x
73 mm
(3-7/16″ x 2-1/2″ x
2-7/8″)
Net weight
without battery 0.06 kg (0.1 lbs)
with BL1016/BL1021B 0.27 kg (0.6 lbs)
with BL1041B 0.43 kg (1.0 lbs)
Symbols
The following show the symbols used for the equipment. Be sure that
you understand their meaning before use.
• Read instruction manual.
• Indoor use only
• Only for EU countries
Do not dispose of electric equipment or battery pack
together with household waste material!
In observance of the European Directives, on Waste
Electric and Electronic Equipment and Batteries and
Accumulators and Waste Batteries and Accumulators
and their implementation in accordance with national
laws, electric equipment and batteries and battery
pack(s) that have reached the end of their life must be
collected separately and returned to an environmentally
compatible recycling facility.
• Optical Radiation (UV and IR).
Minimize exposure to eyes or skin.
• Do not stare at operating lamp.
• Use appropriate shielding or eyes protection.
• Take particular care and attention!
IMPORTANT SAFETY INSTRUCTIONS
WARNING: When using electric luminaires, basic safety
precautions should always be followed to reduce the risk of re,
electric shock, and personal injury, including the following:
READ ALL INSTRUCTIONS.
CAUTION:
1. When the luminaire is not in use, always switch off and
remove the battery cartridge from the luminaire.
2. Do not cover or clog the lit luminaire with cloth or carton, etc.
Covering or clogging it may cause a ame.
3. This battery holder part is not waterproof. Do not use it in
damp or wet locations. Do not expose it to rain or snow. Do
not wash it in water.
4. Do not use the luminaire in explosive atmospheres, such as
in the presence of ammable liquids, gases or dust.
5. Do not look in the LED light or see the source of light directly.
a) Proper assembly, installation, maintenance and safe use,
including clear warnings concerning precautions to avoid
possible exposure to hazardous optical radiation.
b) Advice on safe operation procedures and warnings concerning
reasonably foreseeable malpractices, malfunctions and
hazardous failure modes.
c) NOTICE: UV and IR emitted from this product.
d) WARNING: IR emitted from this product.
e) CAUTION: Possibly hazardous optical radiation emitted from
this product.
f) Minimise exposure to eyes or skin. Use appropriate shielding.
g) Use appropriate shielding or eye protection.
h) Do not stare at operating lamp. May be harmful to the eyes.
i) Eye or skin irritation may result from exposure. Avoid eye
exposure.
IMPORTANT SAFETY INSTRUCTIONS FOR
BATTERY CARTRIDGE
1. Before using battery cartridge, read all instructions and
cautionary markings on (1) battery charger, (2) battery, and
(3) product using battery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively shorter, stop
operating immediately. It may result in a risk of overheating,
possible burns and even an explosion.
4. If electrolyte gets into your eyes, rinse them out with clear
water and seek medical attention right away. It may result in
loss of your eyesight.
5. Do not short the battery cartridge:
(1) Do not touch the terminals with any conductive material.
(2) Avoid storing battery cartridge in a container with other
metal objects such as nails, coins, etc.
(3) Do not expose battery cartridge to water or rain.
A battery short can cause a large current ow, overheating,
possible burns and even a breakdown.
6. Do not store the luminaire and battery cartridge in locations
where the temperature may reach or exceed 50°C (122°F).
7. Do not incinerate the battery cartridge even if it is severely
damaged or is completely worn out. The battery cartridge can
explode in a re.
8. Be careful not to drop or strike battery.
9. Do not use a damaged battery.
10.The contained lithium-ion batteries are subject to the
Dangerous Goods Legislation requirements.
For commercial transports e.g. by third parties, forwarding agents,
special requirement on packaging and labeling must be observed.
For preparation of the item being shipped, consulting an expert
for hazardous material is required. Please also observe possibly
more detailed national regulations.
Tape or mask off open contacts and pack up the battery in such a
manner that it cannot move around in the packaging.
11.Follow your local regulations relating to disposal of battery.
SAVE THESE INSTRUCTIONS.
CAUTION: Only use genuine Makita batteries. Use of non-
genuine Makita batteries, or batteries that have been altered, may
result in the battery bursting causing res, personal injury and
damage. It will also void the Makita warranty for the Makita luminaire
and charger.
Tips for maintaining maximum battery life
1. Charge the battery cartridge before completely discharged.
Always stop luminaire operation and charge the battery cartridge
when you notice less luminaire power.
2. Never recharge a fully charged battery cartridge. Overcharging
shortens the battery service life.
3. Charge the battery cartridge with room temperature at
10°C – 40°C (50°F – 104°F). Let a hot battery cartridge cool down
before charging it.
FCC Cautions to the user
The changes or modications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the equipment.
The equipment has been tested and found to comply with the limits
for a Class B Digital Device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction, may cause
harmful interference to radio communication. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including
interference that may cause undesired operation.
ICES-003 STANDARD : CAN ICES-3(B)/NMB-3(B)
INSTALLING OR REMOVING BATTERY
CARTRIDGE (Fig. A)
To install the battery cartridge (1), align the tongue on the battery
cartridge with the groove in the luminaire (2) and slip it into place.
Always insert it all the way until it locks in place with a little click.
If you can see the red indicator (3) on the upper side of the button
(4), it is not locked completely. Install it fully until the red indicator
cannot be seen. If not, it may accidentally fall out of the luminaire,
causing injury to you or someone around you. To remove the battery
cartridge, slide it from the luminaire while sliding the button on the
front of the cartridge.
BATTERY PROTECTION SYSTEM
The light goes off during operation when the remaining battery
capacity gets low.
This is caused by the activation of protection system and does not
show the light problem. Remove the battery cartridge from the light
and charge it.
LIGHTING UP THE LED LIGHT (Fig. B)
Press the switch (5) once, the light (6) shines. To turn off the light,
press the switch once again.
HANGING LUMINAIRE (Fig. B)
The luminaire equips a strap hole (7). Make use of the hole in
accordance with the situation.
MAINTENANCE
CAUTION: Always be sure that the luminaire is switched
off and the battery cartridge is removed before attempting to
perform inspection or maintenance.
CLEANING
From time to time wipe off the outside (luminaire body) of the
luminaire using a cloth dampened in soapy water.
CAUTION: Never use gasoline, benzine, thinner, alcohol or
the like. Discoloration, deformation or cracks may result.
To maintain product SAFETY and RELIABILITY, repairs, any
other maintenance or adjustment should be performed by
Makita Authorized Service Centers, always using Makita
replacement parts.
OPTIONAL ACCESSORIES
CAUTION: These accessories or attachments are
recommended for use with your Makita luminaire specied in
this manual. The use of any other accessories or attachments
might present a risk of injury to persons. Only use accessory or
attachment for its stated purpose.
If you need any assistance for more details regarding these
accessories, ask your local Makita Service Center.
• Makita genuine battery and charger
NOTE: Some items in the list may be included in the luminaire
package as standard accessories. They may differ from country to
country.

INSTRUCTION MANUAL
Cordless Impact Wrench
WT02
IMPORTANT:Read Before Using.

SPECIFICATIONS
Model: WT02
Fastening capacities Standard bolt M8 - M16 (5/16″ - 5/8″)
High tensile bolt M6 - M12 (1/4″ - 1/2″)
Square drive 9.5 mm (3/8″)
No load speed (RPM) 0 - 2,600 /min
Impacts per minute 0 - 3,200 /min
Overall length 161 mm (6-3/8″)
Rated voltage D.C. 10.8 V - 12 V max
Net weight 1.0 - 1.2 kg (2.3 - 2.7 lbs)
• Due to our continuing program of research and development, the specications herein are subject to change
without notice.
• Specications may differ from country to country.
• The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi-
est combination, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Battery cartridge BL1016 / BL1021B / BL1041B
Charger DC10SB / DC10WD
• Some of the battery cartridges and chargers listed above may not be available depending on your region of
residence.
WARNING: Only use the battery cartridges and chargers listed above. Use of any other battery cartridges
and chargers may cause injury and/or re.
SAFETY WARNINGS
General power tool safety warnings
WARNING: Read all safety warnings, instruc-
tions, illustrations and specications provided
with this power tool. Failure to follow all instructions
listed below may result in electric shock, re and/or
serious injury.
Save all warnings and instruc-
tions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or BATTERY-
operated (cordless) power tool.
Work area safety
1. Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
2. Do not operate power tools in explosive atmo-
spheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
3. Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
Electrical Safety
1. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodied plugs and matching outlets will
reduce risk of electric shock.
2. Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of elec-
tric shock if your body is earthed or grounded.
3. Do not expose power tools to rain or wet con-
ditions. Water entering a power tool will increase
the risk of electric shock.
4. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
5. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
6. If operating a power tool in a damp location is
unavoidable, use a ground fault circuit inter-
rupter (GFCI) protected supply. Use of a GFCI
reduces the risk of electric shock.

7.
Power tools can produce electromagnetic elds
(EMF) that are not harmful to the user. However,
users of pacemakers and other similar medical
devices should contact the maker of their device and/
or doctor for advice before operating this power tool.
Personal Safety
1. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the inuence of drugs, alcohol or med-
ication. A moment of inattention while operating
power tools may result in serious personal injury.
2. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
3. Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or BATTERY pack, pick-
ing up or carrying the tool. Carrying power tools
with your nger on the switch or energising power
tools that have the switch on invites accidents.
4. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
5. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
6. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewel-
lery or long hair can be caught in moving parts.
7. If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
8.
Do not let familiarity gained from frequent use
of tools allow you to become complacent and
ignore tool safety principles. A careless action can
cause severe injury within a fraction of a second.
9. Always wear protective goggles to protect your
eyes from injury when using power tools.The
goggles must comply with ANSI Z87.1 in the USA.
It is an employer's responsibility to enforce
the use of appropriate safety protective equip-
ments by the tool operators and by other per-
sons in the immediate working area.
Power tool use and care
1. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
2. Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.
3.
Disconnect the plug from the power source and/
or remove the BATTERY pack, if detachable,
from the power tool before making any adjust-
ments, changing accessories, or storing power
tools. Such preventive safety measures reduce the
risk of starting the power tool accidentally.
4. Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
5. Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition that
may affect the power tool’s operation. If dam-
aged, have the power tool repaired before use.
Many accidents are caused by poorly maintained
power tools.
6. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
7. Use the power tool, accessories and tool bits
etc. in accordance with these instructions, tak-
ing into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended could
result in a hazardous situation.
8. Keep handles and grasping surfaces dry,
clean and free from oil and grease. Slippery
handles and grasping surfaces do not allow for
safe handling and control of the tool in unexpected
situations.
9. When using the tool, do not wear cloth work
gloves which may be entangled. The entangle-
ment of cloth work gloves in the moving parts may
result in personal injury.
BATTERY tool use and care
1. Recharge only with the charger specied by
the manufacturer. A charger that is suitable for
one type of BATTERY pack may create a risk of
re when used with another BATTERY pack.
2. Use power tools only with specically des-
ignated BATTERY packs. Use of any other
BATTERY packs may create a risk of injury and
re.
3. When BATTERY pack is not in use, keep it
away from other metal objects, like paper
clips, coins, keys, nails, screws or other small
metal objects, that can make a connection
from one terminal to another. Shorting the
BATTERY terminals together may cause burns or
a re.
4. Under abusive conditions, liquid may be
ejected from the BATTERY; avoid contact. If
contact accidentally occurs, ush with water.
If liquid contacts eyes, additionally seek med-
ical help. Liquid ejected from the BATTERY may
cause irritation or burns.
5. Do not use a BATTERY pack or tool that is
damaged or modied. Damaged or modied
batteries may exhibit unpredictable behaviour
resulting in re, EXPLOSION or risk of injury.
6. Do not expose a BATTERY pack or tool to re
or excessive temperature. Exposure to re or
temperature above 130 °C may cause explosion.
7. Follow all charging instructions and do not
charge the BATTERY pack or tool outside the
temperature range specied in the instruc-
tions. Charging improperly or at temperatures
outside the specied range may damage the
BATTERY and increase the risk of re.

Service
1. Have your power tool serviced by a qualied
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
2. Never service damaged BATTERY packs.
Service of BATTERY packs should only be per-
formed by the manufacturer or authorized service
providers.
3. Follow instruction for lubricating and chang-
ing accessories.
Cordless impact wrench safety
warnings
1. Hold the power tool by insulated gripping
surfaces, when performing an operation
where the fastener may contact hidden wiring.
Fasteners contacting a "live" wire may make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.
2. Wear ear protectors.
3. Check the impact socket carefully for wear,
cracks or damage before installation.
4. Hold the tool rmly.
5. Keep hands away from rotating parts.
6. Always be sure you have a rm footing.
Be sure no one is below when using the tool in
high locations.
7. The proper fastening torque may differ
depending upon the kind or size of the bolt.
Check the torque with a torque wrench.
SAVE THESE INSTRUCTIONS.
WARNING: DO NOT let comfort or familiarity
with product (gained from repeated use) replace
strict adherence to safety rules for the subject
product.
MISUSE or failure to follow the safety rules stated
in this instruction manual may cause serious
personal injury.
Symbols
The followings show the symbols used for tool.
volts
direct current
no load speed
revolutions or reciprocation per minute
number of blow
Important safety instructions for
battery cartridge
1. Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using
battery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4. If electrolyte gets into your eyes, rinse them
out with clear water and seek medical atten-
tion right away. It may result in loss of your
eyesight.
5. Do not short the battery cartridge:
(1) Do not touch the terminals with any con-
ductive material.
(2) Avoid storing battery cartridge in a con-
tainer with other metal objects such as
nails, coins, etc.
(3) Do not expose battery cartridge to water
or rain.
A battery short can cause a large current
ow, overheating, possible burns and even a
breakdown.
6. Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50 °C (122 °F).
7. Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a re.
8. Be careful not to drop or strike battery.
9. Do not use a damaged battery.
10. The contained lithium-ion batteries are subject
to the Dangerous Goods Legislation require-
ments.
For commercial transports e.g. by third parties,
forwarding agents, special requirement on pack-
aging and labeling must be observed.
For preparation of the item being shipped, consult-
ing an expert for hazardous material is required.
Please also observe possibly more detailed
national regulations.
Tape or mask off open contacts and pack up the
battery in such a manner that it cannot move
around in the packaging.
11. Follow your local regulations relating to dis-
posal of battery.
12. Use the batteries only with the products
specied by Makita. Installing the batteries to
non-compliant products may result in a re, exces-
sive heat, explosion, or leak of electrolyte.
SAVE THESE INSTRUCTIONS.
CAUTION: Only use genuine Makita batteries.
Use of non-genuine Makita batteries, or batteries that
have been altered, may result in the battery bursting
causing res, personal injury and damage. It will
also void the Makita warranty for the Makita tool and
charger.