Makita DDF482 User manual

DDF482
EN Cordless Driver Drill INSTRUCTION MANUAL 5
PL Akum. wiertarko-wkrętarka INSTRUKCJA OBSŁUGI 11
HU Akkumulátoros
fúró-csavarbehajtó HASZNÁLATI KÉZIKÖNYV 18
SK Ľahký vŕtací skrutkovač NÁVOD NA OBSLUHU 24
CS Akumulátorový vrtací
šroubovák NÁVOD K OBSLUZE 30
UK Дриль із бездротовим
приводом
ІНСТРУКЦІЯ З
ЕКСПЛУАТАЦІЇ 36
RO Maşină de găurit şi înşurubat
cu acumulator MANUAL DE INSTRUCŢIUNI 43
DE Akku-Bohrschrauber BETRIEBSANLEITUNG 49

3
1
2
Fig.1
1
Fig.2
1
2
Fig.3
1
Fig.4
1
Fig.5
1
A B
Fig.6
1
Fig.7
2
1
3
Fig.8
2

1
2
3
Fig.9
2
1
3
Fig.10
2
1
Fig.11
Fig.12
1
Fig.13
2
1
Fig.14
2
1
3
Fig.15
1
Fig.16
3

1
2
Fig.17
1
2
Fig.18
4

5ENGLISH
ENGLISH (Original instructions)
SPECIFICATIONS
Model: DDF482
Drilling capacities Steel 13 mm
Wood 38 mm
Fastening capacities Wood screw 10 mm x 90 mm
Machine screw M6
No load speed High (2) 0 - 1,900 min-1
Low (1) 0 - 600 min-1
Overall length 185 mm
Rated voltage D.C. 18 V
Battery cartridge BL1815N, BL1820, BL1820B BL1830, BL1840, BL1850, BL1830B,
BL1840B, BL1850B, BL1860B
Net weight 1.5 kg 1.7 kg
• Duetoourcontinuingprogramofresearchanddevelopment,thespecicationshereinaresubjecttochange
without notice.
• Specicationsandbatterycartridgemaydifferfromcountrytocountry.
• Weight,withbatterycartridge,accordingtoEPTA-Procedure01/2003
Intended use
Thetoolisintendedfordrillingandscrewdrivingin
wood, metal and plastic.
Noise
ThetypicalA-weightednoiseleveldeterminedaccord-
ingtoEN60745:
Sound pressure level (LpA):75dB(A)
Uncertainty(K):3dB(A)
Thenoiselevelunderworkingmayexceed80dB(A).
WARNING: Wear ear protection.
Vibration
Thevibrationtotalvalue(tri-axialvectorsum)deter-
minedaccordingtoEN60745:
Workmode:drillingintometal
Vibrationemission(ah,D):2.5m/s2or less
Uncertainty(K):1.5m/s2
NOTE:Thedeclaredvibrationemissionvaluehas
beenmeasuredinaccordancewiththestandardtest
methodandmaybeusedforcomparingonetoolwith
another.
NOTE:Thedeclaredvibrationemissionvalue
mayalsobeusedinapreliminaryassessmentof
exposure.
WARNING:Thevibrationemissionduringactual
use of the power tool can differ from the declared
emission value depending on the ways in which the
tool is used.
WARNING: Be sure to identify safety measures
toprotecttheoperatorthatarebasedonanestima-
tion of exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it is
running idle in addition to the trigger time).
EC Declaration of Conformity
For European countries only
MakitadeclaresthatthefollowingMachine(s):
DesignationofMachine:CordlessDriverDrill
ModelNo./Type:DDF482
ConformstothefollowingEuropeanDirectives:
2006/42/EC
Theyaremanufacturedinaccordancewiththefollowing
standardorstandardizeddocuments:EN60745
Thetechnicalleinaccordancewith2006/42/ECis
availablefrom:
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
30.3.2015
Yasushi Fukaya
Director
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium

6ENGLISH
General power tool safety warnings
WARNING: Read all safety warnings and
all instructions. Failure to follow the warnings and
instructionsmayresultinelectricshock,reand/or
seriousinjury.
Save all warnings and instruc-
tions for future reference.
Theterm"powertool"inthewarningsreferstoyour
mains-operated(corded)powertoolorbattery-operated
(cordless) power tool.
Cordless driver drill safety warnings
1. Use auxiliary handle(s), if supplied with the
tool.Lossofcontrolcancausepersonalinjury.
2.
Hold power tool by insulated gripping sur-
faces, when performing an operation where the
cutting accessory may contact hidden wiring.
Cuttingaccessorycontactinga"live"wiremay
makeexposedmetalpartsofthepowertool"live"
and could give the operator an electric shock.
3. Hold power tool by insulated gripping sur-
faces, when performing an operation where
the fastener may contact hidden wiring.
Fastenerscontactinga"live"wiremaymake
exposedmetalpartsofthepowertool"live"and
could give the operator an electric shock.
4. Always be sure you have a rm footing. Be
sure no one is below when using the tool in
high locations.
5. Hold the tool rmly.
6. Keep hands away from rotating parts.
7. Do not leave the tool running. Operate the tool
only when hand-held.
8. Do not touch the drill bit or the workpiece
immediately after operation; they may be
extremely hot and could burn your skin.
9. Some material contains chemicals which may
be toxic. Take caution to prevent dust inhala-
tion and skin contact. Follow material supplier
safety data.
SAVE THESE INSTRUCTIONS.
WARNING: DO NOT let comfort or familiarity
with product (gained from repeated use) replace
strict adherence to safety rules for the subject
product. MISUSE or failure to follow the safety
rules stated in this instruction manual may cause
serious personal injury.
Important safety instructions for
battery cartridge
1.
Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using battery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4. If electrolyte gets into your eyes, rinse them
out with clear water and seek medical atten-
tion right away. It may result in loss of your
eyesight.
5. Do not short the battery cartridge:
(1) Do not touch the terminals with any con-
ductive material.
(2) Avoid storing battery cartridge in a con-
tainer with other metal objects such as
nails, coins, etc.
(3) Do not expose battery cartridge to water
or rain.
A battery short can cause a large current
ow, overheating, possible burns and even a
breakdown.
6. Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50 °C (122 °F).
7. Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a re.
8. Be careful not to drop or strike battery.
9. Do not use a damaged battery.
10. The contained lithium-ion batteries are subject
to the Dangerous Goods Legislation require-
ments.
Forcommercialtransportse.g.bythirdparties,
forwarding agents, special requirement on pack-
agingandlabelingmustbeobserved.
Forpreparationoftheitembeingshipped,consult-
ing an expert for hazardous material is required.
Pleasealsoobservepossiblymoredetailed
national regulations.
Tapeormaskoffopencontactsandpackupthe
batteryinsuchamannerthatitcannotmove
around in the packaging.
11. Follow your local regulations relating to dis-
posal of battery.
SAVE THESE INSTRUCTIONS.
CAUTION: Only use genuine Makita batteries.
Useofnon-genuineMakitabatteries,orbatteriesthat
havebeenaltered,mayresultinthebatterybursting
causingres,personalinjuryanddamage.Itwill
also void the Makita warranty for the Makita tool and
charger.
Tips for maintaining maximum
battery life
1. Charge the battery cartridge before completely
discharged. Always stop tool operation and
charge the battery cartridge when you notice
less tool power.
2. Never recharge a fully charged battery car-
tridge. Overcharging shortens the battery
service life.
3. Charge the battery cartridge with room tem-
perature at 10 °C - 40 °C (50 °F - 104 °F). Let
a hot battery cartridge cool down before
charging it.
4. Charge the battery cartridge if you do not use
it for a long period (more than six months).

7ENGLISH
FUNCTIONAL
DESCRIPTION
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before adjusting or checking function on the tool.
Installing or removing battery
cartridge
CAUTION: Always switch off the tool before
installing or removing of the battery cartridge.
CAUTION: Hold the tool and the battery car-
tridge rmly when installing or removing battery
cartridge.Failuretoholdthetoolandthebattery
cartridgermlymaycausethemtoslipoffyourhands
andresultindamagetothetoolandbatterycartridge
andapersonalinjury.
►Fig.1: 1. Red indicator 2. Button 3. Battery cartridge
Toremovethebatterycartridge,slideitfromthetool
whileslidingthebuttononthefrontofthecartridge.
Toinstallthebatterycartridge,alignthetongueonthe
batterycartridgewiththegrooveinthehousingandslip
itintoplace.Insertitallthewayuntilitlocksinplace
withalittleclick.Ifyoucanseetheredindicatoronthe
uppersideofthebutton,itisnotlockedcompletely.
CAUTION: Always install the battery cartridge
fully until the red indicator cannot be seen.Ifnot,
itmayaccidentallyfalloutofthetool,causinginjuryto
you or someone around you.
CAUTION: Do not install the battery cartridge
forcibly.Ifthecartridgedoesnotslideineasily,itis
notbeinginsertedcorrectly.
Battery protection system
Lithium-ion battery with star marking
►Fig.2: 1. Star marking
Lithium-ionbatterieswithastarmarkingareequipped
withaprotectionsystem.Thissystemautomatically
cutsoffpowertothetooltoextendbatterylife.
Thetoolwillautomaticallystopduringoperationifthe
tooland/orbatteryareplacedunderoneofthefollowing
conditions:
Overloaded:
Thetoolisoperatedinamannerthatcausesittodraw
anabnormallyhighcurrent.
Inthissituation,turnthetooloffandstoptheapplication
thatcausedthetooltobecomeoverloaded.Thenturn
the tool on to restart.
Ifthetooldoesnotstart,thebatteryisoverheated.In
thissituation,letthebatterycoolbeforeturningthetool
on again.
Low battery voltage:
Theremainingbatterycapacityistoolowandthetool
willnotoperate.Inthissituation,removeandrecharge
thebattery.
Indicating the remaining battery
capacity
Only for battery cartridges with "B" at the end of the
model number
►Fig.3: 1.Indicatorlamps2.Checkbutton
Pressthecheckbuttononthebatterycartridgetoindi-
catetheremainingbatterycapacity.Theindicatorlamps
light up for few seconds.
Indicator lamps Remaining
capacity
Lighted Off Blinking
75% to 100%
50% to 75%
25% to 50%
0% to 25%
Charge the
battery.
Thebattery
may have
malfunctioned.
NOTE: Depending on the conditions of use and the
ambienttemperature,theindicationmaydifferslightly
from the actual capacity.
Switch action
►Fig.4: 1. Switch trigger
CAUTION: Before installing the battery car-
tridge into the tool, always check to see that the
switch trigger actuates properly and returns to
the "OFF" position when released.
Tostartthetool,simplypulltheswitchtrigger.Tool
speedisincreasedbyincreasingpressureontheswitch
trigger. Release the switch trigger to stop.
Lighting up the front lamp
►Fig.5: 1. Lamp
CAUTION: Do not look in the light or see the
source of light directly.
Pulltheswitchtriggertolightupthelamp.Thelamp
keepsonlightingwhiletheswitchtriggerisbeingpulled.
Thelampgoesout10-15secondsafterreleasingthe
trigger.
NOTE: Use a dry cloth to wipe the dirt off the lens of
the lamp. Be careful not to scratch the lens of lamp, or
it may lower the illumination.

8ENGLISH
Reversing switch action
►Fig.6: 1. Reversing switch lever
CAUTION: Always check the direction of
rotation before operation.
CAUTION: Use the reversing switch only after
the tool comes to a complete stop. Changing the
directionofrotationbeforethetoolstopsmaydam-
age the tool.
CAUTION: When not operating the tool,
always set the reversing switch lever to the neu-
tral position.
Thistoolhasareversingswitchtochangethedirection
of rotation. Depress the reversing switch lever from the
AsideforclockwiserotationorfromtheBsideforcoun-
terclockwise rotation.
When the reversing switch lever is in the neutral posi-
tion,theswitchtriggercannotbepulled.
Speed change
►Fig.7: 1. Speed change lever
CAUTION: Always set the speed change lever
fully to the correct position.Ifyouoperatethe
tool with the speed change lever positioned halfway
betweenthe"1"sideand"2"side,thetoolmaybe
damaged.
CAUTION: Do not use the speed change lever
while the tool is running.Thetoolmaybedamaged.
Position of
speed
change lever
Speed Torque Applicable
operation
1Low High Heavy load-
ing operation
2High Low Light loading
operation
Tochangethespeed,switchoffthetoolrst.Select
the"2"sideforhighspeedor"1"forlowspeedbuthigh
torque. Be sure that the speed change lever is set to the
correctpositionbeforeoperation.
Ifthetoolspeediscomingdownextremelyduringthe
operationwith"2",slidethelevertothe"1"andrestart
the operation.
Adjusting the fastening torque
►Fig.8: 1.Adjustingring2. Graduation 3.Arrow
Thefasteningtorquecanbeadjustedin22stepsbyturningtheadjustingring.Alignthegraduationswiththearrow
onthetoolbody.Youcangettheminimumfasteningtorqueat1andmaximumtorqueat marking.
Theclutchwillslipatvarioustorquelevelswhensetatthenumber1to21.Theclutchdoesnotworkat
the marking.
Before actual operation, drive a trial screw into your material or a piece of duplicate material to determine which
torque level is required for a particular application.
Thefollowingshowstheroughguideoftherelationshipbetweenthescrewsizeandgraduation.
Graduation 12345678 9 10 11 12 13 14 15 16 17 18 19 20 21
Machine screw M4 M5 M6
Wood
screw
Soft wood
(e.g. pine)
–ɸ3.5 x 22 ɸ4.1x 38 –
Hard wood
(e.g. lauan)
–ɸ3.5 x 22 ɸ4.1x 38 –
ASSEMBLY
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Installing or removing driver bit/
drill bit
►Fig.9: 1. Sleeve 2. Close 3. Open
Turnthesleevecounterclockwisetoopenthechuck
jaws.Placethedriverbit/drillbitinthechuckasfar
asitwillgo.Turnthesleeveclockwisetotightenthe
chuck.Toremovethedriverbit/drillbit,turnthesleeve
counterclockwise.
Installing hook
►Fig.10: 1. Groove 2. Hook 3. Screw
Thehookisconvenientfortemporarilyhangingthetool.
Thiscanbeinstalledoneithersideofthetool.Toinstall
the hook, insert it into a groove in the tool housing on
eithersideandthensecureitwithascrew.Toremove,
loosen the screw and then take it out.
Installing driver bit holder
Optional accessory
►Fig.11: 1.Driverbitholder2.Driverbit
Fitthedriverbitholderintotheprotrusionatthetoolfoot
on either right or left side and secure it with a screw.
Whennotusingthedriverbit,keepitinthedriverbit
holders.Driverbits45mm-longcanbekeptthere.

9ENGLISH
OPERATION
CAUTION: Always insert the battery cartridge
all the way until it locks in place.Ifyoucanseethe
redindicatorontheuppersideofthebutton,itisnot
lockedcompletely.Insertitfullyuntiltheredindicator
cannotbeseen.Ifnot,itmayaccidentallyfalloutof
thetool,causinginjurytoyouorsomeonearound
you.
CAUTION: When the speed comes down
extremely, reduce the load or stop the tool to
avoid the tool damage.
Holdthetoolrmlywithonehandonthegripandthe
otherhandonthebottomofthebatterycartridgeto
control the twisting action.
►Fig.12
Screwdriving operation
CAUTION: Adjust the adjusting ring to the
proper torque level for your work.
CAUTION: Make sure that the driver bit is
inserted straight in the screw head, or the screw
and/or driver bit may be damaged.
Placethepointofthedriverbitinthescrewheadand
apply pressure to the tool. Start the tool slowly and then
increase the speed gradually. Release the switch trigger
as soon as the clutch cuts in.
NOTE: When driving wood screw, pre-drill a pilot hole
2/3thediameterofthescrew.Itmakesdrivingeasier
and prevents splitting of the workpiece.
Drilling operation
First,turntheadjustingringsothatthepointerpointsto
the marking.Thenproceedasfollows.
Drilling in wood
Whendrillinginwood,thebestresultsareobtained
withwooddrillsequippedwithaguidescrew.Theguide
screwmakesdrillingeasierbypullingthedrillbitinto
the workpiece.
Drilling in metal
Topreventthedrillbitfromslippingwhenstartinga
hole, make an indentation with a center-punch and
hammeratthepointtobedrilled.Placethepointofthe
drillbitintheindentationandstartdrilling.
Useacuttinglubricantwhendrillingmetals.Theexcep-
tionsareironandbrasswhichshouldbedrilleddry.
CAUTION: Pressing excessively on the tool
will not speed up the drilling.Infact,thisexcessive
pressure will only serve to damage the tip of your drill
bit,decreasethetoolperformanceandshortenthe
service life of the tool.
CAUTION: Hold the tool rmly and exert care
when the drill bit begins to break through the
workpiece.Thereisatremendousforceexertedon
thetool/drillbitatthetimeofholebreakthrough.
CAUTION: A stuck drill bit can be removed
simply by setting the reversing switch to reverse
rotation in order to back out. However, the tool
may back out abruptly if you do not hold it rmly.
CAUTION: Always secure small workpieces
in a vise or similar hold-down device.
CAUTION: If the tool is operated continuously
until the battery cartridge has discharged, allow
the tool to rest for 15 minutes before proceeding
with a fresh battery.
MAINTENANCE
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
NOTICE: Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
Replacing carbon brushes
►Fig.13: 1. Limit mark
Checkthecarbonbrushesregularly.
Replace them when they wear down to the limit mark.
Keepthecarbonbrushescleanandfreetoslipinthe
holders.Bothcarbonbrushesshouldbereplacedatthe
sametime.Useonlyidenticalcarbonbrushes.
1. Use a screwdriver to remove two screws then
remove the rear cover.
►Fig.14: 1. Rear cover 2. Screw
2. Raise the arm part of the spring and then place
itintherecessedpartofthehousingwithaslottedbit
screwdriver of slender shaft or the like.
►Fig.15: 1. Recessed part 2. Spring 3.Arm
3. Useplierstoremovethecarbonbrushcapsof
thecarbonbrushes.Takeouttheworncarbonbrushes,
insertthenewonesandreplacethecarbonbrushcaps
in reverse.
►Fig.16: 1.Carbonbrushcap
4. Make sure to place the lead wire in opposite side
of the arm.
►Fig.17: 1. Lead wire 2.Carbonbrushcap
5. Makesurethatthecarbonbrushcapshavetinto
theholesinbrushholderssecurely.
►Fig.18: 1. Hole 2.Carbonbrushcap

10 ENGLISH
6. Reinstall the rear cover and tighten two screws
securely.
7. Insertthebatterycartridgeintothetoolandbreak
inbrushesbyrunningtoolwithnoloadforabout1
minute.
8. Checkthetoolwhilerunningandelectricbrake
operationwhenreleasingtheswitchtrigger.Ifelectric
brakeisnotworkingwell,askMakitaAuthorizedor
Factory Service Centers for repair.
TomaintainproductSAFETYandRELIABILITY,
repairs,anyothermaintenanceoradjustmentshould
beperformedbyMakitaAuthorizedorFactoryService
Centers, always using Makita replacement parts.
OPTIONAL
ACCESSORIES
CAUTION: These accessories or attachments
are recommended for use with your Makita tool
specied in this manual.Theuseofanyother
accessories or attachments might present a risk of
injurytopersons.Onlyuseaccessoryorattachment
for its stated purpose.
Ifyouneedanyassistanceformoredetailsregard-
ing these accessories, ask your local Makita Service
Center.
• Drillbits
• Driverbits
• Driverbitholder
• Hook
• Makitagenuinebatteryandcharger
NOTE:Someitemsinthelistmaybeincludedinthe
toolpackageasstandardaccessories.Theymay
differ from country to country.

11 POLSKI
POLSKI (Instrukcja oryginalna)
DANE TECHNICZNE
Model: DDF482
Zakresy wiercenia Stal 13 mm
Drewno 38 mm
Zakresydokręcania Wkrętdodrewna 10 mm x 90 mm
Wkrętmaszynowy M6
Prędkośćbezobciążenia
Wysoka (2) 0–1 900 min-1
Niska (1) 0–600 min-1
Długośćcałkowita 185 mm
Napięcieznamionowe Prądstały18V
Akumulator BL1815N, BL1820, BL1820B BL1830, BL1840, BL1850, BL1830B,
BL1840B, BL1850B, BL1860B
Ciężarnetto 1,5 kg 1,7 kg
• Wzwiązkuzestaleprowadzonymprzeznasząrmęprogramembadawczo-rozwojowymniniejszedanemogą
uleczmianombezwcześniejszegopowiadomienia.
• Winnychkrajachurządzeniemożemiećodmienneparametrytechniczneimożebyćwyposażonewinny
akumulator.
• MasaurządzeniawrazzakumulatoremobliczonazgodniezprocedurąEPTA01/2003
Przeznaczenie
Narzędziejestprzeznaczonedowierceniawdrewnie,
metaluitworzywachsztucznychorazdowkręcania
wkrętówwewspomnianemateriały.
Hałas
TypowyrównoważnypoziomdźwiękuAokreślonyw
oparciuonormęEN60745:
Poziomciśnieniaakustycznego(LpA):75dB(A)
Niepewność(K):3dB(A)
Poziomhałasupodczaspracymożeprzekraczać80
dB(A).
OSTRZEŻENIE: Nosić ochronniki słuchu.
Drgania
Całkowitawartośćpoziomudrgań(sumawektoróww3
osiach)określonazgodnieznormąEN60745:
Trybpracy:wierceniewmetalu
Emisjadrgań(ah,D):2,5m/s2lubmniej
Niepewność(K):1,5m/s2
WSKAZÓWKA:Deklarowanawartośćwytwarzanych
drgańzostałazmierzonazgodniezestandardową
metodątestowąimożnająwykorzystaćdoporówny-
wanianarzędzi.
WSKAZÓWKA:Deklarowanąwartośćwytwarzanych
drgańmożnatakżewykorzystaćwewstępnejocenie
narażenia.
OSTRZEŻENIE: Drgania wytwarzane podczas
rzeczywistegoużytkowaniaelektronarzędziamogą
sięróżnićodwartoścideklarowanej,wzależnościod
sposobujegoużytkowania.
OSTRZEŻENIE: W oparciu o szacowane
narażeniewrzeczywistychwarunkachużytkowania
należyokreślićśrodkibezpieczeństwawceluochrony
operatora(uwzględniającwszystkieelementycyklu
działania,tj.czas,kiedynarzędziejestwyłączonei
kiedypracujenabiegujałowym,atakżeczas,kiedy
jestwłączone).
Deklaracja zgodności WE
Dotyczy tylko krajów europejskich
FirmaMakitaoświadcza,żeponiższeurządzenie(-a):
Oznaczeniemaszyny:Akum.wiertarko-wkrętarka
Modelnr/typ:DDF482
Jestzgodnezwymogamiokreślonymiwnastępujących
dyrektywacheuropejskich:2006/42/EC
Jest/sąprodukowanezgodnieznastępującyminor-
mamilubdokumentaminormalizacyjnymi:EN60745
Dokumentacjatechnicznazgodnawwymaganiami
dyrektywy2006/42/ECjestdostępnaw:
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgia
30.3.2015
Yasushi Fukaya
Dyrektor
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgia

12 POLSKI
Ogólne zasady bezpiecznej
eksploatacji elektronarzędzi
OSTRZEŻENIE: Przeczytać wszystkie ostrze-
żenia bezpieczeństwa i wszystkie instrukcje.
Niezastosowaniesiędowspomnianychostrzeżeńi
instrukcjimożedoprowadzićdoporażeniaprądem
elektrycznym,pożarui/lubpoważnychobrażeńciała.
Wszystkie ostrzeżenia i instruk-
cje należy zachować do wykorzy-
stania w przyszłości.
Pojęcie„elektronarzędzie",występującewwymienio-
nychtuostrzeżeniach,odnosisiędoelektronarzędzia
zasilanegozsiecielektrycznej(zprzewodemzasilają-
cym)lubdoelektronarzędziaakumulatorowego(bez
przewoduzasilającego).
Ostrzeżenia dotyczące
bezpieczeństwa dla akumulatorowej
wiertarko-wkrętarki
1. Używać narzędzia z uchwytami pomocniczymi,
jeśli zostały dostarczone wraz z nim. Utrata
kontrolimożespowodowaćobrażeniaciała.
2. Trzymać elektronarzędzie za izolowane
powierzchnie rękojeści podczas wykonywania
prac, przy których wiertło może dotknąć niewi-
docznej instalacji elektrycznej.Zetknięciewier-
tłazprzewodemelektrycznymznajdującymsię
podnapięciemmożespowodować,żeodsłonięte
elementymetaloweelektronarzędziarównież
znajdąsiępodnapięciem,grożącporażeniem
operatoraprądemelektrycznym.
3. Trzymać elektronarzędzie za izolowane
powierzchnie rękojeści podczas wykonywania
prac, przy których wkręcany wkręt lub śruba
mogą dotknąć niewidocznej instalacji elek-
trycznej.Zetknięciewkrętulubśrubyzprzewo-
demelektrycznymznajdującymsiępodnapięciem
spowoduje,żeodsłonięteelementymetalowe
narzędziarównieżznajdąsiępodnapięciem,gro-
żącporażeniemoperatoraprądemelektrycznym.
4. Podczas pracy należy zadbać o dobre oparcie
dla nóg. W przypadku pracy na pewnej wyso-
kości upewnić się, że na dole nie przebywają
żadne osoby.
5. Narzędzie należy trzymać mocno i pewnie.
6. Trzymać ręce z dala od części obrotowych.
7. Nie pozostawiać włączonego narzędzia.
Narzędzie można uruchomić tylko, gdy jest
trzymane w rękach.
8. Nie dotykać wiertła ani części obrabianej od
razu po zakończeniu danej operacji; mogą one
być bardzo gorące i spowodować oparzenie
skóry.
9. Niektóre materiały zawierają substancje
chemiczne, które mogą być toksyczne.
Unikać wdychania pyłu i kontaktu ze skórą.
Przestrzegać przepisów bezpieczeństwa poda-
nych przez dostawcę materiałów.
ZACHOWAĆ NINIEJSZE
INSTRUKCJE.
OSTRZEŻENIE: NIE WOLNO pozwolić,
aby wygoda lub rutyna (nabyta w wyniku wielo-
krotnego używania urządzenia) zastąpiły ścisłe
przestrzeganie zasad bezpieczeństwa obsługi.
NIEWŁAŚCIWE UŻYTKOWANIE narzędzia lub
niestosowanie się do zasad bezpieczeństwa
podanych w niniejszej instrukcji obsługi może
prowadzić do poważnych obrażeń ciała.
Ważne zasady bezpieczeństwa
dotyczące akumulatora
1.
Przed użyciem akumulatora zapoznać się ze
wszystkimi instrukcjami i znakami ostrzegaw-
czymi na (1) ładowarce, (2) akumulatorze i (3)
produkcie, w którym będzie używany akumulator.
2. Akumulatora nie wolno rozbierać.
3. Jeśli czas działania uległ znacznemu skróce-
niu, należy natychmiast przerwać pracę. Może
bowiem dojść do przegrzania, ewentualnych
poparzeń, a nawet eksplozji.
4. W przypadku przedostania się elektrolitu do
oczu, przemyć je czystą wodą i niezwłocznie
uzyskać pomoc lekarską. Może on bowiem
spowodować utratę wzroku.
5. Nie doprowadzać do zwarcia akumulatora:
(1) Nie dotykać styków materiałami przewo-
dzącymi prąd.
(2) Unikać przechowywania akumulatora w
pojemniku z metalowymi przedmiotami,
takimi jak gwoździe, monety itp.
(3) Chronić akumulator przed deszczem lub
wodą.
Zwarcie prowadzi do przepływu prądu elek-
trycznego o dużym natężeniu i przegrzania
akumulatora, co w konsekwencji może grozić
poparzeniami a nawet awarią urządzenia.
6. Narzędzia i akumulatora nie wolno przecho-
wywać w miejscach, w których temperatura
osiąga bądź przekracza 50°C (122°F).
7. Akumulatorów nie wolno spalać, również tych
poważnie uszkodzonych lub całkowicie zuży-
tych. Akumulator może eksplodować w ogniu.
8.
Chronić akumulator przed upadkiem i uderzeniami.
9. Nie wolno używać uszkodzonego akumulatora.
10.
Stanowiące wyposażenie akumulatory lito-
wo-jonowe podlegają przepisom dotyczącym
produktów niebezpiecznych.
Napotrzebytransportukomercyjnego,np.świad-
czonegoprzezrmytrzecieczyspedycyjne,należy
przestrzegaćspecjalnychwymagańwzakresie
pakowania i oznaczania etykietami.
Przygotowanieproduktudowysyłkiwymagaskon-
sultowaniasięzespecjalistąds.materiałówniebez-
piecznych.Należytakżeprzestrzegaćprzepisów
krajowych,któremogąbyćbardziejszczegółowe.
Zakleićtaśmąlubzaślepićotwartestykiakumula-
toraorazzabezpieczyćgo,abyniemógłsięprze-
suwaćwopakowaniu.
11. Postępować zgodnie z przepisami lokalnymi
dotyczącymi usuwania akumulatorów.

13 POLSKI
ZACHOWAĆ NINIEJSZE
INSTRUKCJE.
PRZESTROGA: Używać wyłącznie oryginal-
nych akumulatorów rmy Makita.Używanienie-
oryginalnychakumulatorówrminnychniżMakitalub
akumulatorów,którezostałyzmodykowane,może
spowodowaćwybuchakumulatoraipożar,obrażenia
ciałaorazzniszczeniemienia.Stanowitorównież
naruszeniewarunkówgwarancjirmyMakitadoty-
czącychnarzędziaiładowarki.
Wskazówki dotyczące zacho-
wania maksymalnej trwałości
akumulatora
1. Akumulator należy naładować zanim zostanie
do końca rozładowany. Po zauważeniu spadek
mocy narzędzia należy przerwać pracę i nała-
dować akumulator.
2. Nie wolno ładować powtórnie w pełni nałado-
wanego akumulatora. Przeładowanie akumula-
tora skraca jego trwałość.
3. Akumulator należy ładować w temperaturze
pokojowej w przedziale 10–40°C (50–104°F). W
przypadku gorącego akumulatora przed przy-
stąpieniem do ładowania należy poczekać, aż
ostygnie.
4. Akumulatory niklowo-wodorkowe należy nała-
dować po okresie długiego nieużytkowania
(dłuższego niż sześć miesięcy).
OPIS DZIAŁANIA
PRZESTROGA: Przed przystąpieniem do regu-
lacji lub przeglądu narzędzia upewnić się, że jest
ono wyłączone, a akumulator został wyjęty.
Wkładanie i wyjmowanie
akumulatora
PRZESTROGA: Przed włożeniem lub wyjęciem
akumulatora należy zawsze wyłączyć narzędzie.
PRZESTROGA: Podczas wkładania lub wyjmo-
wania akumulatora należy mocno trzymać narzę-
dzie i akumulator.Wprzeciwnymraziemogąsięone
wyślizgnąćzrąk,powodującuszkodzenienarzędzia
lubakumulatoraiobrażeniaciała.
►Rys.1: 1.Czerwonywskaźnik2.Przycisk
3.Akumulator
Abywyjąćakumulator,przesuńprzyciskznajdującysię
wprzedniejjegoczęściiwysuńakumulator.
Abywłożyćakumulator,wyrównajwystępnaakumu-
latorzezrowkiemwobudowieiwsuńgonaswoje
miejsce.Akumulatornależywsunąćdooporu,ażsię
zatrzaśnienamiejscu,cojestsygnalizowanedelikat-
nymkliknięciem.Jeśliwgórnejczęściprzyciskujest
widocznyczerwonywskaźnik,akumulatorniezostał
całkowiciezatrzaśnięty.
PRZESTROGA: Akumulator należy włożyć
do końca, tak aby czerwony wskaźnik nie był
widoczny.Wprzeciwnymraziemożeprzypadkowo
wypaśćznarzędzia,powodującobrażeniaoperatora
lubosóbpostronnych.
PRZESTROGA: Nie wkładać akumulatora na
siłę.Jeśliakumulatorniedajesięswobodniewsunąć,
oznaczato,żezostałwłożonynieprawidłowo.
Układ zabezpieczenia akumulatora
Akumulator litowo-jonowy oznaczony gwiazdką
►Rys.2: 1. Znak gwiazdki
Akumulatorylitowo-jonowezeznakiemgwiazdkisą
wyposażonewukładzabezpieczający.Układtenauto-
matycznieodcinazasilanienarzędziawceluwydłuże-
niażywotnościakumulatora.
Narzędziezostanieautomatyczniezatrzymanepod-
czaspracywnastępującychsytuacjachzwiązanychz
narzędziem/akumulatorem:
Przeciążenie:
Narzędziepracujewsposób,którypowodujepobór
nadmierniewysokiegoprądu.
Wtakiejsytuacjinależywyłączyćnarzędzieizaprze-
staćwykonywaniaczynnościpowodującejprzeciążenie
narzędzia.Następnienależywłączyćnarzędziewcelu
jegoponownegouruchomienia.
Jeślinarzędzienieuruchomisię,oznaczato,żeaku-
mulatorjestprzegrzany.Wtakiejsytuacji,przedponow-
nymuruchomieniemnarzędzianależyodczekać,aż
akumulator ostygnie.
Niskie napięcie akumulatora:
Poziomnaładowaniaakumulatorajestzbytniski,aby
narzędziemogłopracować.Wtakiejsytuacjinależy
wyjąćakumulatorigonaładować.
Wskazanie stanu naładowania
akumulatora
Tylko akumulatory oznaczone literą „B” na końcu
model
►Rys.3: 1.Lampkiwskaźnika2.Przyciskkontrolny
Nacisnąćprzyciskkontrolnynaakumulatorzewcelu
wyświetleniastanunaładowaniaakumulatora.Lampki
wskaźnikazaświecąsięprzezkilkasekund.
Lampki wskaźnika Pozostała
energia
akumulatora
Świeci się Wyłączony Miga
75–100%
50–75%
25–50%
0–25%
Naładować
akumulator.

14 POLSKI
Lampki wskaźnika Pozostała
energia
akumulatora
Świeci się Wyłączony Miga
Akumulator
możenie
działać
poprawnie.
WSKAZÓWKA:Zależnieodwarunkówużytkowania
itemperaturyotoczenia,wskazywanypoziommoże
nieznaczniesięróżnićodrzeczywistegostanunała-
dowania akumulatora.
Działanie przełącznika
►Rys.4: 1.Spustprzełącznika
PRZESTROGA: Przed włożeniem akumulatora
do narzędzia należy zawsze sprawdzić, czy spust
przełącznika działa prawidłowo i czy powraca do
położenia wyłączenia po jego zwolnieniu.
Wceluuruchomienianarzędziawystarczypociągnąć
spustprzełącznika.Prędkośćnarzędziazwiększasię
wrazzezwiększaniemnaciskunaspustprzełącznika.
Wceluzatrzymaniaurządzenianależyzwolnićspust
przełącznika.
Włączanie lampki czołowej
►Rys.5: 1. Lampka
PRZESTROGA: Nie patrzeć na światło ani
bezpośrednio na źródło światła.
Wceluwłączenialampkinależypociągnąćzaspust
przełącznika.Lampkaświeci,dopókispustprzełącznika
jestnaciskany.Lampkagaśniepo10–15sodzwolnie-
niaspustuprzełącznika.
WSKAZÓWKA:Abyusunąćzabrudzeniazklosza
lampki,należyużyćsuchejszmatki.Uważać,abynie
zarysowaćkloszalampki,gdyżmożetozmniejszyć
natężenieoświetlenia.
Działanie przełącznika zmiany
kierunku obrotów
►Rys.6: 1.Dźwigniaprzełącznikazmianykierunku
obrotów
PRZESTROGA: Przed przystąpieniem do pracy
należy zawsze sprawdzić ustawiony kierunek
obrotów.
PRZESTROGA: Przełącznika zmiany kie-
runku obrotów można użyć tylko po całkowitym
zatrzymaniu narzędzia.Zmianakierunkuobro-
tówprzedzatrzymaniemsięnarzędziagrozijego
uszkodzeniem.
PRZESTROGA: Gdy narzędzie nie jest uży-
wane, należy zawsze ustawić dźwignię prze-
łącznika zmiany kierunku obrotów w położeniu
neutralnym.
Omawianenarzędziejestwyposażonewprzełącznik
umożliwiającyzmianękierunkuobrotów.Wceluuzy-
skaniaobrotówwprawąstronęnależywcisnąćdźwi-
gnięprzełącznikazmianykierunkuobrotówpostronie
A,natomiastabyuzyskaćobrotywlewąstronę,należy
wcisnąćdźwignięprzełącznikapostronieB.
Gdydźwigniaprzełącznikazmianykierunkuobrotów
znajdujesięwpołożeniuneutralnym,spustprzełącz-
nikajestzablokowany.
Zmiana prędkości
►Rys.7: 1.Dźwigniazmianyprędkości
PRZESTROGA: Dźwignię zmiany prędkości
należy zawsze ustawiać dokładnie w wybranej
pozycji.Wprzypadkuuruchomienianarzędziaprzy
dźwignizmianyprędkościustawionejwpołowie
międzypozycją„1"i„2"możedojśćdouszkodzenia
narzędzia.
PRZESTROGA: Nie wolno używać dźwi-
gni zmiany prędkości, gdy narzędzie pracuje.
Narzędziemożeulecuszkodzeniu.
Położenie
dźwigni
zmiany
prędkości
Prędkość Moment
obrotowy
Odpowiedni
tryb pracy
1Niska Wysoka Pracaprzy
dużym
obciążeniu
2Wysoki Niski Pracaprzy
małym
obciążeniu
Wceluzmianyprędkościnależynajpierwwyłączyć
narzędzie.Wybraćpołożenie„2”wceluustawienia
wysokiejprędkościlubpołożenie„1”wceluustawienia
niskiejprędkości,aledużegomomentu.Przedrozpo-
częciempracynależysprawdzić,czydźwigniazmiany
prędkościjestustawionawewłaściwympołożeniu.
Jeśliprędkośćnarzędziadrastyczniespadniepodczas
pracyzdźwigniąustawionąwpołożeniu„2”,należy
przesunąćdźwigniędopołożenia„1”iponownieprzy-
stąpićdopracy.

15 POLSKI
Regulacja momentu dokręcenia
►Rys.8: 1.Pierścieńregulacyjny2.Podziałka
3.Strzałka
Momentdokręceniamożnaregulowaćw22stopniach,obracającpierścieńregulacyjny.Wyrównaćpodziałkęze
strzałkąznajdującąsięnakorpusienarzędzia.Położenie1odnosisiędominimalnegomomentudokręcenia,asym-
bol domaksymalnegomomentudokręcenia.
Sprzęgłobędzieślizgaćsięprzyróżnychwartościachmomentudlaustawieńod1do21.Natomiastdlaustawie-
nia sprzęgłoniebędziedziałać.
Przedprzystąpieniemdopracynależyprzeprowadzićpróbęwkręcaniawdanyelementlubinnyelementztego
samegomateriału,abyustalićpoziommomentudokręceniawymaganywdanymzastosowaniu.
Poniższatabelaprzedstawiaogólnązależnośćpomiędzyrozmiaremwkrętuapodziałką.
Podziałka 12345678 9 10 11 12 13 14 15 16 17 18 19 20 21
Wkrętmaszynowy M4 M5 M6
Wkrętdo
drewna
Miękkie
drewno
(np. sosna)
–ɸ3,5 x 22 ɸ4,1 x 38 –
Twarde
drewno
(np.
mahoń)
–ɸ3,5 x 22 ɸ4,1 x 38 –
MONTAŻ
PRZESTROGA: Przed przystąpieniem do prac
konserwacyjnych przy narzędziu upewnić się,
że jest ono wyłączone, a akumulator został wyjęty.
Wkładanie i wyjmowanie końcówki
wkrętakowej/wiertła
►Rys.9: 1.Tuleja2. Zamykanie 3. Otwieranie
Abyotworzyćszczękiuchwytu,obrócićtulejęwlewąstronę.
Umieścićjaknajgłębiejkońcówkęwkrętakową/wiertłowuchwycie.
Obrócićtulejęwprawąstronę,abyzacisnąćuchwyt.Wceluwyję-
ciakońcówkiwkrętakowej/wiertłaobrócićtulejęwlewąstronę.
Zamontowanie zaczepu
►Rys.10: 1. Rowek 2. Zaczep 3.Wkręt
Zaczepsłużydowygodnego,tymczasowegozawieszania
narzędzia.Możnagozamontowaćzjednejlubzdrugiej
stronynarzędzia.Abyzamontowaćzaczep,należywsunąć
gowrowekwobudowienarzędziaznajdującysięzobu
stron,anastępnieprzykręcićgowkrętem.Abywymonto-
waćzaczep,należyodkręcićwkrętiwyjąćzaczep.
Zamontowywanie uchwytu
końcówki wkrętakowe
Akcesoria opcjonalne
►Rys.11: 1.Uchwytnakońcówkiwkrętakowe
2.Końcówkawkrętakowa
Włożyćuchwytnakońcówkiwkrętakowedowystępuw
stopienarzędziazprawejbądźzlewejstronyiprzymo-
cowaćgowkrętem.
Nieużywanekońcówkiwkrętakowenależytrzymać
wuchwycie.Wuchwyciemożnatrzymaćkońcówkio
długości45mm.
OBSŁUGA
PRZESTROGA: Akumulator należy wsunąć
do oporu, aż wskoczy na swoje miejsce.Jeślijest
widocznyczerwonywskaźnikwgórnejczęściprzy-
cisku,akumulatorniezostałcałkowiciezatrzaśnięty.
Należygowsunąćdooporu,ażczerwonywskaźnik
przestaniebyćwidoczny.Wprzeciwnymraziemoże
onprzypadkowowypaśćznarzędzia,powodując
obrażeniaoperatoralubosóbpostronnych.
PRZESTROGA: W przypadku drastycznego
spadku prędkości należy zredukować obciążenie
lub wyłączyć narzędzie, aby nie dopuścić do jego
uszkodzenia.
Narzędzienależytrzymaćjednąrękązauchwyt,a
drugązaspódakumulatora,abykontrolowaćjego
przekręcanie.
►Rys.12
Wkręcanie
PRZESTROGA: Ustawić pierścień regulacyjny
w pozycji odpowiadającej właściwemu dla danej
operacji momentowi dokręcenia.
PRZESTROGA: Końcówka wkrętakowa
powinna być wprowadzona do łba wkrętu w linii
prostej z wkrętem, w przeciwnym razie wkręt i/lub
końcówka mogą ulec uszkodzeniu.
Wsunąćczubekkońcówkiwkrętakowejdogniazdawe
łbiewkrętuidocisnąćnarzędzie.Uruchomićnarzędzie
powoli,anastępniestopniowozwiększaćprędkość.
Zwolnićspustprzełącznika,gdytylkozadziałasprzęgło.
WSKAZÓWKA:Wprzypadkuwkręcaniawkrętudo
drewnanależywstępnienawiercićotwórprowadzący
ośrednicy2/3średnicywkrętu.Ułatwitowkręcaniei
zapobiegnierozłupywaniusięelementuobrabianego.

16 POLSKI
Wiercenie
Najpierwobrócićpierścieńregulacyjnytak,abystrzałka
wskazywałasymbol .Następniepostępowaćzgod-
niezponiższymopisem.
Wiercenie w drewnie
Wprzypadkuwierceniawdrewnienajlepszerezultaty
uzyskujesię,stosującwiertłazakończonewkrętem
prowadzącym.Wkrętprowadzącyułatwiawiercenie,
ponieważwciągawiertłowelementobrabiany.
Wiercenie w metalu
Abyuniknąćześlizgiwaniasięwiertłanapoczątku
operacji,należyzapomocąpunktakaimłotkawykonać
wgłębieniewmiejscu,wktórymmabyćwykonany
otwór.Umieścićkońcówkęwiertławewgłębieniuiroz-
począćwiercenie.
Podczaswierceniawmetalunależystosowaćodpo-
wiedniechłodziwo.Wyjątkistanowiążelazoimosiądz,
którenależywiercićnasucho.
PRZESTROGA: Wywieranie nadmiernego
nacisku na narzędzie nie przyspiesza wiercenia.
W praktyce, wywieranie nadmiernego nacisku przy-
czyniasięjedyniedouszkodzeniakońcówkiwiertła,
zmniejszeniawydajnościiskróceniaokresueksplo-
atacyjnegonarzędzia.
PRZESTROGA: Gdy wiertło zaczyna przebijać
na wylot otwór w obrabianym elemencie, należy
zachować ostrożność i mocno trzymać narzędzie.
Wmomencieprzebijaniaotworunanarzędzie/wiertło
wywieranajestolbrzymiasiła.
PRZESTROGA: Zakleszczone wiertło można
łatwo wyjąć, zmieniając kierunek obrotów i wycią-
gając wiertło. Należy jednak pamiętać, że narzę-
dzie może się gwałtownie cofnąć, jeśli nie będzie
mocno trzymane.
PRZESTROGA: Niewielkie elementy obrabiane
należy zawsze zamocować w imadle lub podob-
nym przyrządzie.
PRZESTROGA: Jeżeli narzędzie jest używane
bez przerwy aż do rozładowania akumulatora,
należy je odstawić na 15 minut przed podjęciem
pracy na nowo z użyciem innego naładowanego
akumulatora.
KONSERWACJA
PRZESTROGA: Przed przystąpieniem do prze-
glądu narzędzia lub jego konserwacji upewnić się,
że jest ono wyłączone, a akumulator wyjęty.
UWAGA: Nie stosować benzyny, rozpuszczalni-
ków, alkoholu itp. środków. Mogą one powodo-
wać odbarwienia, odkształcenia lub pęknięcia.
Wymiana szczotek węglowych
►Rys.13: 1. Oznaczenie limitu
Systematyczniesprawdzaćszczotkiwęglowe.
Wymieniaćje,gdyichzużyciesięgaoznaczenialimitu.
Szczotkiwęglowepowinnybyćczyste,abymożnaje
byłoswobodniewsunąćdoopraw.Należywymieniać
obydwieszczotkijednocześnie.Stosowaćwyłącznie
identyczneszczotkiwęglowe.
1. Zapomocąśrubokrętawykręćdwawkręty,a
następniezdejmijtylnąosłonę.
►Rys.14: 1.Tylnaosłona2.Wkręt
2. Zapomocącienkiegośrubokrętapłaskiegolub
podobnegonarzędziapodnieśramięsprężyny,a
następniewsuńjewgniazdowobudowie.
►Rys.15: 1. Gniazdo 2.Sprężyna3.Ramię
3. Zapomocąszczypiecwyjmijnasadkiszczotek
węglowych.Wyjmijzużyteszczotkiwęglowe,włóżnowe
izpowrotemzałóżnasadkiszczotek,wykonującczyn-
nościwodwrotnejkolejności.
►Rys.16: 1.Nasadkaszczotkiwęglowej
4. Upewnijsię,żeprzewódbiegniepoprzeciwnej
stronie ramienia.
►Rys.17: 1.Przewód2.Nasadkaszczotkiwęglowej
5. Upewnijsię,żenasadkiszczotekwęglowych
dobrzetkwiąwotworachuchwytówszczotek.
►Rys.18: 1.Otwór2.Nasadkaszczotkiwęglowej
6. Załóżzpowrotemtylnąosłonę,anastępnie
dobrzedokręćobawkręty.
7. Pozakończeniuwymianyszczotekwłóżakumula-
tordonarzędziaiwłączjenaokoło1minbezobciąże-
nia,abydotrzećszczotki.
8. Następniesprawdździałanienarzędziapodczas
pracy.Sprawdźtakżeskutecznośćhamulcaelektrycz-
negopozwolnieniuspustuprzełącznika.Jeślihamulec
elektrycznyniedziałaprawidłowo,zlećnaprawęurzą-
dzeniaautoryzowanemulubfabrycznemupunktowi
serwisowemunarzędziMakita.
W celu zachowania odpowiedniego poziomu
BEZPIECZEŃSTWAiNIEZAWODNOŚCIproduktu
wszelkienaprawyiróżnegorodzajupracekonserwa-
cyjnelubregulacjepowinnybyćprzeprowadzaneprzez
autoryzowanylubfabrycznypunktserwisowynarzędzi
Makita,zawszezużyciemoryginalnychczęścizamien-
nych Makita.

17 POLSKI
AKCESORIA
OPCJONALNE
PRZESTROGA: Zaleca się stosowanie wymie-
nionych akcesoriów i przystawek razem z narzę-
dziem Makita opisanym w niniejszej instrukcji.
Stosowanieinnychakcesoriówlubprzystawek
możebyćprzyczynąobrażeńciała.Akcesorialub
przystawkinależywykorzystywaćtylkozgodniezich
przeznaczeniem.
Wraziepotrzebywszelkiejpomocyiszczegółowych
informacjinatematniniejszychakcesoriówudzielą
PaństwulokalnepunktyserwisoweMakita.
• Wiertła
• Końcówkiwkrętakowe
• Uchwytnakońcówkiwkrętakowe
• Zaczep
• OryginalnyakumulatoriładowarkarmyMakita
WSKAZÓWKA:Niektórepozycjeznajdującesięna
liściemogąbyćdołączonedopakietunarzędziowego
jakoakcesoriastandardowe.Mogątobyćróżne
pozycje,wzależnościodkraju.

18 MAGYAR
MAGYAR (Eredeti utasítások)
RÉSZLETES LEÍRÁS
Típus: DDF482
Fúrásiteljesítmény Acél 13 mm
Fa 38 mm
Meghúzásiteljesítmény Facsavar 10 mm x 90 mm
Gépcsavar M6
Üresjáratifordulatszám Magas (2) 0 - 1 900 min-1
Alacsony(1) 0 - 600 min-1
Teljeshossz 185 mm
Névlegesfeszültség 18 V, egyenáram
Akkumulátor BL1815N, BL1820, BL1820B BL1830, BL1840, BL1850, BL1830B,
BL1840B, BL1850B, BL1860B
Tisztatömeg 1,5 kg 1,7 kg
• Folyamatoskutató-ésfejlesztőprogramunkeredményekéntazittfelsorolttulajdonságokgyelmeztetésnélkül
megváltozhatnak.
• Aműszakiadatokésazakkumulátorországonkéntváltozhatnak.
• Súlyazakkumulátorral,a01/2003EPTAeljárásszerintmeghatározva
Rendeltetés
Aszerszámfúrásraéscsavarbehajtásrahasználható,
fába,fémekbeésműanyagokba.
Zaj
AtipikusA-súlyozásúzajszint,aEN60745szerint
meghatározva:
Hangnyomásszint (LpA):75dB(A)
Bizonytalanság(K):3dB(A)
Azajszintamunkavégzéssoránmeghaladhatjaa80
dB(A)értéket.
FIGYELMEZTETÉS: Viseljen fülvédőt!
Vibráció
Avibrációteljesértéke(háromtengelyűvektorösszeg)
azEN60745szerintmeghatározva:
Üzemmód:fúrásfémbe
Rezgéskibocsátás(ah,D):2,5m/s2vagykisebb
Bizonytalanság(K):1,5m/s2
MEGJEGYZÉS:Arezgéskibocsátásértékeaszabvá-
nyosvizsgálatieljárásnakmegfelelőenlettmérve,és
segítségévelazelektromoskéziszerszámokössze-
hasonlíthatókegymással.
MEGJEGYZÉS:Arezgéskibocsátásértékéneksegít-
ségévelelőzetesenmegbecsülhetőarezgésnekvaló
kitettségmértéke.
FIGYELMEZTETÉS:Aszerszámrezgéskibo-
csátásaegyadottalkalmazásnáleltérhetamegadott
értéktőlahasználatmódjátólfüggően.
FIGYELMEZTETÉS:Határozzamegakezelő
védelmétszolgálómunkavédelmilépéseket,melyek
azadottmunkafeltételekmellettivibrációshatás
becsültmértékénalapulnak(gyelembevévea
munkacikluselemeit,mintpéldáulagépleállításának
ésüresjáratánakmennyiségétazelindításokszáma
mellett).
EK Megfelelőségi nyilatkozat
Csak európai országokra vonatkozóan
AMakitakijelenti,hogyazalábbigép(ek):
Gépmegnevezése:Akkumulátorosfúró-csavarbehajtó
Típussz./Típus:DDF482
MegfelelakövetkezőEurópaiirányelveknek:
2006/42/EC
Gyártásaakövetkezőszabványoknak,valamintszab-
ványosítottdokumentumoknakmegfelelőentörténik:
EN60745
Aműszakileírása2006/42/ECelőírásainakmegfele-
lőenelérhetőinnen:
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
30.3.2015
Yasushi Fukaya
Igazgató
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium

19 MAGYAR
A szerszámgépekre vonatkozó
általános biztonsági
gyelmeztetések
FIGYELMEZTETÉS: Olvassa el az összes
biztonsági gyelmeztetést és utasítást. Ha nem
tartjabeagyelmeztetéseketésutasításokat,akkor
áramütés,tűzés/vagysúlyossérüléskövetkezhetbe.
Őrizzen meg minden gyelmez-
tetést és utasítást a későbbi tájé-
kozódás érdekében.
Agyelmeztetésekbenszereplő"szerszámgép"kife-
jezésazÖnhálózatról(vezetékes)vagyakkumulá-
torról(vezetéknélküli)működtetettszerszámgépére
vonatkozik.
Biztonsági gyelmeztetések
akkumulátoros
fúró-csavarbehajtóhoz
1. Használja a szerszámhoz mellékelt kisegítő
fogantyúkat.Azirányításelvesztéseszemélyi
sérüléstokozhat.
2. A szerszámgépet a szigetelt markolófelülete-
inél fogja, ha olyan műveletet végez, amikor
a vágóeszköz rejtett vezetékkel érintkezhet.
Áramalattlévővezetékekkelvalóérintkezéskora
szerszámfémalkatrészeiisáramalákerülhetnek,
ésmegrázhatjákakezelőt.
3. Tartsa az elektromos szerszámot a szige-
telt markolófelületeinél fogva amikor olyan
műveletet végez, amelyben fennáll a veszélye,
hogy a rögzítő rejtett vezetékekbe ütközhet.A
rögzítőkáramalattlévővezetékekkelvalóérint-
kezésekoraszerszámfémalkatrészeiisáramalá
kerülnek,ésmegrázhatjákakezelőt.
4. Mindig stabil helyzetben dolgozzon. A szer-
szám magasban történő használatkor győződ-
jön meg arról, hogy nem tartózkodik-e valaki
odalent.
5. Biztosan tartsa a szerszámot.
6. Ne nyúljon a forgó részekhez.
7. Ne hagyja a működő szerszámot felügye-
let nélkül. Csak kézben tartva használja a
szerszámot.
8. Ne érintse meg a fúróhegyet vagy a munkada-
rabot közvetlenül a művelet befejezése után;
rendkívül forrók lehetnek és megégethetik.
9. Egyes anyagok mérgező vegyületet tartal-
mazhatnak. Gondoskodjon a por belélegzése
elleni és érintés elleni védelemről. Tartsa be az
anyag szállítójának biztonsági utasításait.
ŐRIZZE MEG EZEKET AZ
UTASÍTÁSOKAT.
FIGYELMEZTETÉS: NE HAGYJA, hogy (a
termék többszöri használatából eredő) kényelem
és megszokás váltsa fel a termék biztonsági
előírásainak szigorú betartását. A HELYTELEN
HASZNÁLAT és a használati útmutatóban sze-
replő biztonsági előírások megszegése súlyos
személyi sérülésekhez vezethet.
Fontos biztonsági utasítások az
akkumulátorra vonatkozóan
1.
Az akkumulátor használata előtt tanulmányozza át
az akkumulátortöltőn (1), az akkumulátoron (2) és
az akkumulátorral működtetett terméken (3) olvas-
ható összes utasítást és gyelmeztető jelzést.
2. Ne szerelje szét az akkumulátort.
3. Ha a működési idő nagyon lerövidült, azonnal
hagyja abba a használatot. Ez a túlmelegedés,
esetleges égések és akár robbanás veszélyé-
vel is járhat.
4. Ha elektrolit kerül a szemébe, mossa ki azt
tiszta vízzel és azonnal kérjen orvosi segítsé-
get. Ez a látásának elvesztését okozhatja.
5. Ne zárja rövidre az akkumulátort:
(1) Ne érjen az érintkezőkhöz elektromosan
vezető anyagokkal.
(2) Ne tárolja az akkumulátort más fémtár-
gyakkal, mint pl. szegekkel, érmékkel,
stb. egy helyen.
(3) Ne tegye ki az akkumulátort víznek vagy
esőnek.
Az akkumulátor rövidzárlata nagy áramerőssé-
get, túlmelegedést, égéseket, sőt akár meghi-
básodást is okozhat.
6. Ne tárolja a szerszámot vagy az akkumulátort
olyan helyen, ahol a hőmérséklet elérheti vagy
meghaladhatja az 50 °C-ot (122 °F).
7. Ne égesse el az akkumulátort még akkor
sem, ha az komolyan megsérült vagy teljesen
elhasználódott. Az akkumulátor a tűzben
felrobbanhat.
8. Vigyázzon, nehogy leejtse vagy megüsse az
akkumulátort.
9. Ne használjon sérült akkumulátort.
10. A készülékben található lítium-ion akkumuláto-
rokra a veszélyes árukkal kapcsolatos előírá-
sok vonatkoznak.
Atermékpl.harmadikfelek,fuvarozócégekstb.
általtörténőszállításaeseténmindenesetben
tartsaszemelőttacsomagolásonésacímkén
találhatóspeciáliskövetelményeket.
Atermékszállításratörténőfelkészítéseesetén
vegyefelakapcsolatotegyveszélyesanyagokkal
foglalkozószakemberrel.Kérjük,hogyazeset-
legesenszigorúbbnemzetielőírásokatisvegye
gyelembe.
Ragasszaleakiállóérintkezőket,illetveoly
módoncsomagoljabeazakkumulátort,hogyaz
netudjonelmozdulniacsomagolásban.
11. Az akkumulátor ártalmatlanításakor tartsa be a
helyi előírásokat.

20 MAGYAR
ŐRIZZE MEG EZEKET AZ
UTASÍTÁSOKAT.
VIGYÁZAT: Csak eredeti Makita akkumuláto-
rokat használjon.AnemeredetiMakitaakkumu-
látorokvagymódosítottakkumulátorokhasználata
eseténazakkumulátorfelrobbanhat,amitüzet,
személyisérüléstésanyagikártokozhat.AMakita
szerszámraéstöltőrevonatkozóMakitagaranciátis
érvénytelenítheti.
Tippek az akkumulátor maximá-
lis élettartamának eléréséhez
1. Töltse fel az akkumulátort, mielőtt teljesen
lemerülne. Állítsa le a gépet, és töltse fel az
akkumulátort, ha a gép erejének csökkenését
észleli.
2. Soha ne töltse újra a teljesen feltöltött akku-
mulátort. A túltöltés csökkenti az akkumulátor
élettartamát.
3. Töltse az akkumulátort szobahőmérsékleten,
10 °C - 40 °C (50 °F - 104 °F) között. Töltés előtt
hagyja lehűlni a fölforrósodott akkumulátort.
4. Töltse fel az akkumulátort, ha hosszabb ideje
(több mint hat hónapja) nem használta azt.
A MŰKÖDÉS LEÍRÁSA
VIGYÁZAT: Minden esetben ellenőrizze, hogy
a szerszám ki van kapcsolva és az akkumulátor
eltávolításra került mielőtt beállít vagy ellenőriz
valamilyen funkciót a szerszámon.
Az akkumulátor behelyezése és
eltávolítása
VIGYÁZAT: Mindig kapcsolja ki az eszközt,
mielőtt behelyezi vagy eltávolítja az akkumulátort.
VIGYÁZAT: Az akkumulátor behelyezésekor
vagy eltávolításakor erősen fogja meg a szerszá-
mot és az akkumulátort.Hanemfogjaerősena
szerszámotésazakkumulátort,azokkicsúszhatnaka
kezeiközül,amiaszerszámésazakkumulátorkáro-
sodásához,deakárszemélyisérüléshezisvezethet.
►Ábra1: 1.Pirosjel2.Gomb3.Akkumulátor
Azakkumulátoregységkivételéheznyomjabeazakku-
mulátoregységelejéntalálhatógombot,éshúzzalea
gépről.
Azakkumulátorbeszereléséhezillesszeazakkumulá-
tornyelvétaburkolatontalálhatóvájatbaéscsúsztassa
ahelyére.Egészenaddigtoljabe,amígazakkumulátor
egykiskattanássalahelyérenemugrik.Haláthatóa
pirosjelagombfelsőoldalán,akkoragombnemkat-
tantbeteljesen.
VIGYÁZAT: Mindig tolja be teljesen az akku-
mulátort, amíg a piros jel el nem tűnik. Ha ez nem
történikmeg,akkorazakkumulátorkieshetaszer-
számból,ésÖnnekvagyakörnyezetébenmásnak
sérüléstokozhat.
VIGYÁZAT: Ne erőltesse az akkumulátort behe-
lyezéskor.Haazakkumulátornemcsúszikbeköny-
nyedén,akkornemmegfelelőenlettbehelyezve.
Akkumulátorvédő rendszer
Csillag jelzéssel ellátott lítiumion akkumulátorok
►Ábra2: 1.Csillagjelzés
Acsillagjelzésselellátottlítiumionakkumulátorokat
akkumulátorvédőrendszerrelszerelikfel.Ezarendszer
automatikusankikapcsoljaaszerszámáramellátását,
ígymegnöveliazakkumulátorélettartamát.
Aszerszámhasználatközbenautomatikusanleáll,ha
aszerszámés/vagyazakkumulátorakövetkezőhely-
zetbekerül:
Túlterhelt:
Aszerszámotúgyműködteti,hogyáramfelvételeren-
dellenesen magas.
Ilyenkorkapcsoljakiagépet,ésállítsaleaztazalkal-
mazást,amelyikatúlterheléstokozza.Újraindításhoz
kapcsoljabeagépet.
Ha a szerszám nem indul el, az akkumulátor túlmele-
gedett.Ilyenkorhagyjakihűlniazakkumulátort,mielőtt
ismétbekapcsolnáagépet.
Az akkumulátor feszültsége alacsony:
Azakkumulátorfennmaradókapacitásatúlalacsony,a
szerszámotnemtudjaműködtetni.Ilyenkorvegyeleés
töltsefelazakkumulátort.
Other manuals for DDF482
6
This manual suits for next models
3
Table of contents
Languages:
Other Makita Drill manuals

Makita
Makita 6407 User manual

Makita
Makita DDF446 User manual

Makita
Makita 8420V User manual

Makita
Makita 6503D User manual

Makita
Makita 6226DW User manual

Makita
Makita DF001GZ01 User manual

Makita
Makita 8433D User manual

Makita
Makita DS4010 User manual

Makita
Makita M8100 User manual

Makita
Makita DHP484 User manual

Makita
Makita NHP1300S User manual

Makita
Makita DP2010 User manual

Makita
Makita BHP442 User manual

Makita
Makita DHP489 User manual

Makita
Makita HP1640F User manual

Makita
Makita BHP343 User manual

Makita
Makita 6302 User manual

Makita
Makita HP2070 Quick start guide

Makita
Makita DDF458Z User manual

Makita
Makita DHP343 User manual