Manufacturas Lenin COUNTERTOP ECO LENIN PRESS User manual

OPERATION MANUAL
COUNTERTOP ECO LENIN PRESS

IT IS FORBIDDEN TO REPRODUCE TOTAL OR PART OF
THIS MANUAL BY ANY MEANS, WHETHER PRINTED OR
ELECTRICALLY; WITHOUT THE PRIOR, EXPRESS AND
WRITTEN AUTHORIZATION OF THE AUTHOR.

OPERATION MANUAL
COUNTERTOP ECO LENIN PRESS

COUNTERTOP ECO LENIN PRESS Operation manual
4
GENERAL SAFETY INSTRUCTIONS 5
CAUTION 6
ELECTRICAL INSTALLATION 7
COMPONENTS 8
INSTRUCTIONS 9
MAINTENANCE 11
INDEX

COUNTERTOP ECO LENIN PRESS Operation manual
5
GENERAL SAFETY INSTRUCTIONS.
WARNING: To reduce the risk of injury, read all instructions properly. Failure to follow the instructions below can
cause electric shock, fire, serious bodily injury, mutilation, and damage to the machine.
A. SECURITY IN THE WORK AREA.
* Keep the work area clean and lit. Crowded or dark areas lead to accidents.
* Do not operate the equipment without first checking all gas connections with soapy water, to ensure that
there are no leaks that could cause an explosion.
* Keep children, customers and non-company personnel away from the electrical or mechanical operation of
the equipment.
It is recommended to have a minimum space of one meter around the machine for safety and satisfactory
work.
B. ELECTRICAL SAFETY.
* The machinery connections. They must be adapted to the power outlets.
* Do not use adapters for the switches: since you run the risk of receiving an electric shock.
* Do not expose the switches and / or electrical connections to rain or humidity. If water enters these elements
there is a risk that they will decompose or suffer an electric shock.
* Use cable in a single piece, if there are joints in the connections these can produce a short circuit.
* Do not expose cables or electrical connections to heat, oil, sharp edges, or moving parts, as damaged cables
can cause electric shock or short circuit.
C. PERSONAL SAFETY
* Do not operate the equipment if you are tired, under the influence of alcohol or drugs.
* Wear appropriate clothing, do not wear loose clothing, or necklaces, earrings, watches, if you have long hair
wear a cap to keep it up.
* Do not climb on the structure of the machine for any reason, falls or injuries may occur.
* Avoid using headphones, cell phones or any other equipment that works as a distraction for the operator.
* Make correct use of personal protective equipment if any maintenance is to be carried out on the machine.
* If a change is made to the model or component of the equipment, be it electrical, mechanical or gas, it must
be de-energized, cut off the gas supply and stop the machine completely to avoid accidents.
* Keep limbs away from all moving parts.

COUNTERTOP ECO LENIN PRESS Operation manual
6
CAUTION
The following symbols indicate the security measures that must be taken before and after starting the equipment.
HOT HAZARD. Some parts of the machine are hot when in operation.
TAKE CARE OF YOUR HANDS. Hands should not be inserted while working the machine.
ELECTRIC RISK. In which you can suffer electric shocks, if the electrical safety regulations
are not observed.
CRUSHING RISK. Keep hands clear of cam press when in operation.
GEAR HAZARD. Keep your hands away from the chains and gears of the machine.

COUNTERTOP ECO LENIN PRESS Operation manual
7
ELECTRICAL INSTALLATION
Verify that the electrical connection is 110v-220v as the case may be. No shorts, loose wires, or blown fuses.
Ensure all cables are insulated and non-contact, check contactors and switches in good state.
It is recommended to use 12 gauge wire for the installation of the press.
Instalación eléctrica.
Instalación eléctrica 220v.
.
Cable calibre 12 (entubado).
Electrical installation
Electrical installation
110-220v (according to the case)
12 gauge wire (cased)

COUNTERTOP ECO LENIN PRESS Operation manual
8
COMPONENTS
MOTOREDUCTOR
DESLIZADOR
PERILLA AJUSTE DE GROSOR
PANEL DE CONTROL
FOCO PILOTO
INFERIOR Y SUPERIOR
PARO DE
EMERGENCIA.
MOTOR OFF/ON
CONTROL DE
TEMPERATURA
OFF/ON
Thickness adjustment knob
Slider Gearmotor
Temperature control
OFF / ON
Control panel Temperature
control
Lower and upper pilot light
Emergency stop
Motor
OFF / ON

COUNTERTOP ECO LENIN PRESS Operation manual
9
1
3
2
4
Connect press to outlet.
Rotate pyrometer to temperature of 160 ° C.
Lower and upper pilot light will turn on,
it will turn off automatically when it reaches
the selected temperature.
Activate temperature control switch OFF / ON
Activate engine switch OFF / ON
Before starting to operate the equipment, it is recommended to have your wheat flour ready.
56
Take dough. Place dough in press.

COUNTERTOP ECO LENIN PRESS Operation manual
10
78
Verify uniformity of the thickness of the tortilla.
Begin tortilla production. Adjust the thickness of the tortilla:
Rotate counterclockwise to obtain thinner tortillas.
Turn clockwise for thicker tortillas.

COUNTERTOP ECO LENIN PRESS Operation manual
11
MAINTENANCE
Clean the machine before and after use.
The duration of the spare parts will depend on the preventive maintenance and care taken to the machine.
The more frequent maintenance is done, the parts will have a longer life.
LUBRICATION
The following table shows the parts, the type of lubricant, and how often you should lubricate the machine and
its parts.
GENERAL SAFETY INSTRUCTIONS
WARNING: Cleaning the Countertop Eco Lenin Press must be done with the machine completely stopped and
de-energized to avoid accidents such as crushing or electric shock.
CLEANING PROCEDURE
1) Remove excess dough on both aluminum plates.
2) Clean the plates with water, moistening a cloth and gently wiping the aluminum plates.
3) Carry out this action until the plates are free of any flour or dough residue.
4) Clean control panel, sides, blades, motor and keypads.
PIECE LUBRICANT FREQUENCY
Bearings BAT3 Grease Every third day

COUNTERTOP ECO LENIN PRESS Operation manual
12
The following images show the schematic location of the parts that require lubrication.
Lubricate bearing with BAT 3 (A) grease
Lubricate bearing with BAT 3 (A) grease
LUBRICANT
(A) BAT3 Grease

13
HEAD QUARTERS
MEXICANTORTILLAMACHINE.COM
AV. INDUSTRIAS #3665, ZONA INDUSTRIAL C.P. 78395
SAN LUIS POTOSÍ, SLP.
444 127 11 80 444 129 29 79
[email protected]