Maple Systems iR-AI04-TR Series User manual

Installation and Startup Guide
This document covers the installation of iR-AI04-TR, for the detailed specifications and operation,
please refer to Datasheet, Brochure and Remote I/O User Manual. Please read all warnings,
precautions, and instructions on the device carefully before use.
Install Environment:
Electrical
Environment
The product has been tested to conform to European CE requirements. This
means that the circuitry is designed to resist the effects of electrical noise. This
does not guarantee noise immunity in severe cases. Proper wire routing and
grounding will insure proper operation.
Environmental
Considerations
(1) Make sure that the units are installed correctly and that the operating limits
are followed.
(2) Avoid installing units in environments where severe mechanical vibration or
shocks are present.
Unpacking the Unit
Unpack and check the delivery. If damage is found, please contact the supplier.
NOTE: Place the unit on a stable surface during installation. Dropping it or letting it fall may
cause damage.
The package includes:
(1) Installation Instruction, 2-sided A4 *1
(2) Warranty Statment *1
(3) iR-AI04-TR *1
(4) I/O Connector *1
(5) Clips *2
Installation Instructions
Clip assembly: Insert one side of the clip into the hole on the
case. Press down firmly in the direction shown in the figure
on the right until hearing the clip
snap into the case.
Clip removal: Insert a flathead
screwdriver into the gap on the clip
and then lift up the screwdriver.
Placing a finger on the clip when
lifting the screwdriver can prevent
the clip from jumping away. The clip
can also be removed directly by
hand.
Rail mounting: DIN rail 35mm.
Panel mounting: Use two M4 or #8 panhead screws, mounting hole size is 4.6mm
Plan for adequate space around the unit and inside the enclosure, for ventilation and cables. Consider
the heat from other devices inside the enclosure. The ambient temperature around the unit must be 0 ~
55°C
NOTE: Please do not touch any of the connectors when the unit is powered up and running.
iR-AI04-TR series
Installation Instruction
3
1
2
(3) Do not operate the unit in areas subject to explosion hazards due to
flammable gases, vapors or dusts, or where acid gas, such as SO2
exists.
(4) Conform to UL 61010-1 and UL 61010-2-201 safety requirement for use
in Pollution Degree 2 Environment and dry location.
(5) Relative Humidity: 10% ~ 90% (non-condensing)

Connector and Wiring
Connector Specifications:
Wire AWG: 28~16
Operating Temperature: -40°C ~+115°C
Wire Strip Length: 7~8 mm
NOTE: Make sure that all local and national electrical standards are met when
installing the unit. Contact your local authorities to determine which codes apply.
Input Module
Please keep a distance between input signal line and AC power line in order to avoid noise.
Emergency Stop
A Hard-wired EMERGENCY STOP should be fitted in any system using the product.
Hardware
Considerations
The system designer should be aware that devices in Controller systems could fail and
thereby create an unsafe condition. Furthermore, electrical interference in an operator
interface can lead to equipment start-up, which could result in property damage and/or
physical injury to the operator.
If you use any programmable control systems that require an operator, be aware that this
potential safety hazard exists and take appropriate precautions. Although the specific design
steps depend on your particular application, the following precautions generally apply to
installation of solid-state programmable control devices, and conform to the guidelines for
installation of Controllers recommended Control Standards.
Programming
Considerations
Checks should be placed in the controller to ensure that all writable registers that control
critical parts of plant or machinery have limit checks built into the program, with an out-of-limit
safe shut down procedure to ensure safety of personnel.
DANGER
CAUTION
4
Limi
ted Warranty
A copy of the Warranty and Limitation of Liability is contained in the product box. It can
also be found on the Maple Systems website.
1010-1103_rev03_210818
.
Thermocouple Grounded
Ungrounded
.
AF: 0A or newer