Marco TUBULAR FONT User manual

SERVICE MANUAL
Tubular Font no drip tray
Marco Beverage Systems Limited.
63d Heather Road,
Sandyford Industrial Estate,
Dublin 18.
Marco Beverage Systems Limited.
Shire House, Strixton Manor,
Strixton, Wellingborough, Northants, NN29 7PA
Ireland Tel: [phone]
Ireland Fax: [phone]
Email: s[email protected]
www.marco.ie
UK Tel: [phone]
UK Fax: [phone]
Email: sa[email protected]
www.marco-bev.co.uk

Service Manual 1000584 02-02-15 Page 2 of 11
TABLE OF CONTENTS
1. INTRODUCTION....................................................................................................3
2. INSTALLATION......................................................................................................4
a. Mounting.................................................................................................................4
b. Plumbing.................................................................................................................5
c. Electrical.................................................................................................................6
3. CLEANING.............................................................................................................7
4. RISK OF SCALDING .............................................................................................8
5. ASSEMBLY DRAWINGS.......................................................................................9
a. Parts List.................................................................................................................9
b. Replacing the Button............................................................................................11

Service Manual 1000584 02-02-15 Page 3 of 11
1. INTRODUCTION
The information provided in this manual is intended to assist in the installation and
maintenance of the Marco Tubular Font no drip tray. Please read the instructions carefully
to prevent accidents and ensure an efficient installation.
This manual is not a substitute for any safety instructions or technical data affixed to the
machine or its packaging. All information in this manual is current at the time of publication
and is subject to change without notice.
Only technicians or service providers authorised by Marco should carry out installation and
maintenance of these machines.
Marco accepts no responsibility for any damage or injury caused by incorrect or
unreasonable installation and operation.

Service Manual 1000584 02-02-15 Page 4 of 11
2. INSTALLATION
a. Mounting
•Cut a Ø32mm circular cut out in the sink/counter for the font.
•The font is then securely mounted as shown below using the washer and nut
provided.
•The wire and water outlet tube should pass freely through the large hole
through to the underside of the counter.
•For added stability a bead of silicone sealant can be applied to the underside of
the font around the perimeter.
3. Tighten the wing nut up
while threading the wiring
and tube through the
mounting plate.
1. Mount the font on
the sink. Placing the
threaded bar, hose
and wiring through
the hole.
2. Place the mounting
plate back through the
threaded bar, hose and
wiring. Screw the wing nut
back on with the washer.

Service Manual 1000584 02-02-15 Page 5 of 11
b. Plumbing
•This font is supplied with 1.5 metre of silicone tubing.
•One end of this tube should be securely fitted to the reducer connector on the
font and the other end should be connected to the font water outlet connector
(A) on the top of the boiler.
•This tube should be trimmed to ensure a minimum length from boiler to font.
•Connect the wiring from the font to the four way connector (B).
A
B
Reducer connector
(p/n: 1401657)

Service Manual 1000584 02-02-15 Page 6 of 11
c. Electrical
•The wires from the font are terminated in a Mini Fit connector which will plug
into a similar Mini Fit connector mounted on the top lid of the under counter
boiler.
Note: when connected to a Marco under counter boiler the electrical
connections are not polarity sensitive. If a non-Marco Font or Boiler is being
used contact your representative to ensure that the electrical connections are
appropriate.
Mini Fit connector
(p/n: 1400612)

Service Manual 1000584 02-02-15 Page 7 of 11
3. CLEANING
The exterior of the font may be cleaned with a damp cloth and a light detergent. Do not use abrasive cloths or creams, as this will spoil the finish of the font. Do not use a water jet or spray. Beware
of accidentally operating the font when cleaning around the font button.

Service Manual 1000584 02-02-15 Page 8 of 11
4. RISK OF SCALDING
Beware of accidentally operating the font, especially when cleaning around the font button.
The utmost care has been taken in the manufacture and testing of this unit. Failure to install, maintain and/or operate this font according to the manufacturer’s instructions may result
in conditions that can cause bodily injury or damage to property. If in doubt about
the serviceability of the font always contact the manufacturer or your own supplier for
advice.

Service Manual 1000584 02-02-15 Page 9 of 11
5. ASSEMBLY DRAWINGS
a. Parts List
See below table and diagram which lists the different parts in the font.
PART NUMBER
ITEM NO.
DESCRIPTION
1401279
1
NUT M6 S/S WING
1200149
4
Rod M7 threaded 80mm
1400848
5
M4 x 4mm Grub screw
1800316
7
Gasket Switch Tubular Font
2200238
8
Tubular Font 2mm Ring
1401712
9
M3x10mm countersunk screw
1900393
10
Label round PtoD Caution Hot Water
1501221
11
Push button 2 pin 22mm
2200237
12
Tubular Font Clamping Plate
1401124
13
Tubular Font Nozzle
1400055
14
LIQUIDFIT D6 MALE 1/4" BSPT
STANDARD P2
2200236
15
Tubular Font Base Collar
1800546
16
Strain Relief for 6mm wire
1800635
22
Hose PTFE 4mm I.D. x 6mm OD.
1401657
23
Plug in reducer fitting
1401763
24
Screw M4 x 12mm C/Sunk S/S Slot

Service Manual 1000584 02-02-15 Page 10 of 11

Service Manual 1000584 02-02-15 Page 11 of 11
b. Replacing the Button
See below diagram which illustrates how to replace the button on the font. Please note an M3 Philips head screw driver is required to access the button.