Marco Aquatic Fundamentals 13201B Datasheet

MMIIXXEEDDMMEEDDIIAASSTTAANNDD
M
ODEL
13201B F OR 20 G ALLON T ANK
M ODEL 13291B F OR 29 G ALLON T ANK
THANK YOU FOR PURCHASING THIS
QUALITY PIECE OF FURNITURE.
AQUATIC FUNDAMENTALS IS DEDICATED TO
PROVIDING A QUALITY PRODUCT AND WILL MAKE
EVERY ATTEMPT TO DELIVER
CUSTOMER SATISFACTION.
85195 02/05
PARTS LIST
HARDWARE
AQUATIC FUNDAMENTALS
CUSTOMER SERVICE
5400 Doniphan Drive
Neosho, Mo. 64850
C
TOOLS REQUIRED
J
E
DOOR
HINGE
HARDWARE
BAGS
Assemble furniture on the carton or carpet to protect the finish.
Clean furniture with a soft cotton cloth moistened with water.
DO NOT use abrasives.
DO NOT leave water on any of the stand’s surfaces. Always wipe
spilled water from the stand. Water, for prolonged periods, could
damage the stand’s surface.
A
SSEMBLY & C ARE
PHILLIPS HEAD SCREWDRIVER
(8X)
(8X)
(2X)
(4X)
(12X) (12X)
(1X) (2X) (4X)
BF
BEFORE BEGINNING ASSEMBLY:PLEASE REVIEW THE PARTS LIST TO ENSURE THAT
YOU HAVE ALL THE PARTS. IF YOU FIND MISSING OR BROKEN PARTS, OR ARE IN NEED OF ASSEMBLY
GUIDANCE, CALL TOLL FREE, 1-888-627-2601 AND WE’LL BE HAPPY TO HELP.
PLEASE, DO NOT RETURN THIS MERCHANDISE TO THE STORE.
3
A
Visit our Web Page:
www.marcogroupinc.com
E-mail us at:
[e-mail]
D
GH
NOTE:
T HESE H OLES A RE
N OT U SED F OR A NY
A SSEMBLY P URPOSES .
1
5
5
2
2
NNOOTTEE::
THESE HOLES ARE
NOT USED FOR ANY
ASSEMBLY
PURPOSES.
66
I
MPORTANT S AFETY I NFORMATION
PLEASE READ ALL THE FOLLOWING INFORMATION BEFORE
ASSEMBLING AND USING YOUR AQUARIUM STAND.
THIS PRODUCT IS NOT A TOY. NEVER allow small
children to touch, climb on or play with the stand.
Serious injury or death could result.
WHERE TO PLACE YOUR AQUARIUM STAND
Use only a stand designed to support the weight and size of your equipment.
(HINT: If using for an aquarium stand, the filled weight of an aquarium is
approximately 10 to 12 pounds per gallon. This stand is designed only for use on level
surfaces. Failure to place your stand on a level surface could cause the aquarium to
leak, crack or even tip or fall). Never tip the stand from it’s upright position.
MOVING YOUR STAND
Always position the stand in the desired location before putting the equipment in
place. Never attempt to move the stand with the equipment in place.
Never remove an aquarium tank from the stand unless the aquarium tank is
completely empty. Never carry the stand by it’s top.
LIMITED WARRANTY
This aquarium stand is under warranty by Marco Group, Inc. against defects in material and workmanship for 90 days from the date of purchase. If any
component of the stand is found to be defective, you may contact us for replacement provided it has not been modified, damaged or misused.
(Proof of date of purchase must be provided).
THIS WARRANTY IS VOID if the stand is modified, if it is not placed on a flat, level surface, if it is used with a tank other than it is designed,
if it is moved with the tank in place or if it is used for other than it’s intended purpose.
This warranty is limited to replacement of the stand only. Warranty does not cover loss of fish, personal injury, property loss or damage arising out of use of the
aquarium stand. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not
apply to you. This warranty gives you specific legal rights and you may have other rights that vary from state to state.
E
ASY A SSEMBLY
I
NSTRUCTIONS AND
P ARTS L IST
4
ALLEN WRENCH (INCLUDED)
NOTE
EXTENDED
LIP
NOTE
EXTENDED
LIP

5
5
H OLES ARE
F ACING
I NSIDE
2
85195 Pg. 2
FFOOLLLLOOWWSSTTEEPPSSIINNOORRDDEERR::
1. PLACE ONE SPACER “G” INTO THE HINGE
HOLE IN BOTTOM OF PART #2. NOW PLACE
THE BOTTOM DOOR HINGE INTO THIS SPACER.
2. PLACE ONE SPACER “G” ONTO THE TOP
DOOR HINGE AND INSERT IN THE HINGE HOLE
ON TOP PART #2. SECURE TOP HINGE “J” TO
DOOR WITH (2) SCREWS “H” AS SHOWN.
IIMMPPOORRTTAANNTT
IF DOOR DOES NOT OPEN PROPERLY OR IF PART
“E” MOVES WHILE OPENING DOOR, CAREFULLY
RE-CHECK THE INSTALLATION OF PART “E”.
A COMMON MISTAKE IS TO INSTALL PART “E”
BACKWARDS. PLEASE REFER TO PICTURES
IN STEPS 5 & 6 FOR CORRECT ORIENTATION.
TOP VIEW
OF “B”
FRONT VIEW
OF “B”
SSTTEEPP55
A TTACH HARDWARE TO BOTTOM OF
DOORS
FIRST.
OUTSIDE
OF LEFT
DOOR
BOTTOM
DOOR
HINGE
F
HINGE
HOLE
IMPORTANT!!!
NOTE ORIENTATION OF
PART “B”. OPEN (HOLE)
SECTION MUST FACE
TOWARDS THE
CORRESPONDING HOLE
IN EDGE OF PART #’S
4 & 5. (ALL 12 PLACES)
THE ARROW ON TOP OF
PART “B” WILL ALSO
POINT TOWARDS THE
CORRESPONDING HOLE
IN EDGE OF PART
#’S 4 & 5.
SSTTEEPP11
Screw (6) Parts “C” into
each Part #2.
Push in (12) Parts “B” into
both Parts #4 & #5.
PART “B”
MUST BE
INSERTED CORRECTLY.
SEE DETAIL BELOW.
2
4
2
C
1
2
B
5
6
F
H
E
INSIDE
OF LEFT
DOOR
IIMMPPOORRTTAANNTT!!
YOU MUST ATTACH THE HINGE “J” TO
BOTTOM OF EACH DOOR FIRST.
DO NOTATTACH THE HINGES TO THE
TOP OF THE DOORS UNTIL STEP 6.
IF MOUNTING PART “D”
TO MIDDLE SHELF, SEE NOTE IN
STEP 7 FOR CORRECT DOOR
AND HARDWARE ALIGNMENT.
6
INSIDE
OF RIGHT
DOOR
J
D
STEP 6
2X
2X
SSTTEEPP44
Attach other Part #2 onto
both Parts #5 & #4 as shown.
Using a screwdriver, turn all
(10) Parts “B” clockwise to
lock both Parts #5 & #4 into
both Parts #2.
Using the Allen wrench
included, attach Part #1 onto
(4) Parts #3 with (4) Parts “A”.
Attach Part #2 to the (4) Parts
#3 with (4) Parts “A”.
SSTTEEPP22
Attach Part #4 to one Part #2 as shown.
Using a screwdriver, turn clockwise to lock
both Parts “B” onto both Parts “C”.
SSTTEEPP33
Place both Parts #5 onto Parts “C” in Part #2 as shown.
3
A
B5
SSTTEEPP77
G
H
G
J
C
5400 DONIPHAN DRIVE
NEOSHO, MO 64850
IMPORTANT NOTE!
Y OU MUST P OSITION
T ANK T OWARDS THE B ACK
S IDE OF S TAND .
TANK PLACEMENT DETAIL
NOTE: Part “D” may be mounted as shown or
upside down on the middle shelf. If mounting to
middle shelf, you MUST reverse & rotate both doors
so that Part “E” (strikeplate) lines up with Part “D”.
*
*
EXTENDED LIP MUST
BE IN FRONT OF STAND.
SEE DETAIL BELOW FOR
PROPER TANK PLACEMENT.
EXTENDED LIP MUST
BE IN FRONT OF STAND.
SEE DETAIL BELOW FOR
PROPER TANK PLACEMENT.
EX TENDED LIP
4
B
54A
4X