Market Forge Industries M18HPE User manual

OWNER’S MANUAL
TWO BURNER ELECTRIC HOTPLATE
MODEL: M18HPE
35 Garvey Street • Everett • MA • 02149-4403
Tel: [phone] • Toll Free: [phone]
Fax: [phone] (MA and Overseas) • Fax: [phone] (Ex. MA)
E-mail:  • 
S-54A 05/10

TABLE OF CONTENTS
INTRODUCTION1
SERVICE CONNECTIONS1
ILLUSTRATED PARTS2 - 5
MAINTENANCE5
WIRING DIAGRAM6
i

INTRODUCTION
1
Market Forge Model M18-HPE Electric Two Burner Range mounted on a 28” (711mm) high
220mm) cast iron surfaces, located
5.2 KW total

Polished stainless steel cabinet base 18” (457mm) wide shall be of modular design to

with 6” (152mm) stainless steel legs and adjustable bullet feet, and a hinged door with

OPERATION SHALL BE BY:
208 VAC, 60Hz, Three/Single Phase
240 VAC, 60 Hz, Three/Single Phase
SERVICE CONNECTIONS
Electrically Operated
EP Power Supply -Use wire suitable for at
least 90o-

2.6KW each Ele-
ment
Voltage Line 1 Line 2 Line 3
208V, 1-Phase 25 25 --
240V, 1-Phase   --
208V, 3-Phase 25  
240V, 3-Phase   
•
•

CONTROL PANEL
SIDE VIEW
ILLUSTRATED PARTS
2

SIDE VIEW & CONTROL PANEL
ITEM NO. PART NO. DESCRIPTION
1 91-1200 
2A 09-6589 HOTPLATE – 2600W, 208V
2B 09-6590 HOTPLATE – 2600W, 240V
310-5992 CONTROL SWITCH
409-5259 
5 10-5067 
6 10-5068 
7 SUPPLIED W / ELEMENT 
810-8271 CONTROL PANEL
910-6669 INDICATOR LAMP, 250V, 1/3W
10-5170 STRAIGHT CONNECTOR
10-5168 BUSHING
10-2541 SPEED NUT
10-1849 
10-2515 
10-2337 #6-32 HEX NUT
91-1206 
10-5220 GROUND LUG
10-5503 
10-5070 
NOT SHOWN
ILLUSTRATED PARTS
3

4
ILLUSTRATED PARTS

5
ILLUSTRATED PARTS
MAIN ASSEMBLY
ITEM NO. PART NO. DESCRIPTION
1 91-1209 
2 91-3574 TOP COUNTER
3 91-1221 SHIELD PROTECTIVE, ROUND
409-6589 HOTPLATE, 208V, 2600W, ROUND
409-6590 HOTPLATE, 240V, 2600W, ROUND
510-5992 SWITCH, INFINITE HEAT, 10W-15AMP
609-5259 
710-8271 PLATE, NAME, CONTROL PANEL
8 91-1225 STIFFENER, FRAME
9 10-2045 SCREW, CAP, HEX HEAD #10-32 x 5/8 LONG
10 10-2341 WASHER, PLAIN #10
11 10-2509 
12 10-2339 NUT, HEX #10-32
13 10-1761 SCREW, MACH, TRUSS, HEAD #8-32 x 3/8 LONG
14 10-5016 LAMP
, INDICATOR
15 10-2541 NUT, SPEED
16 91-3544 SHIELD, PROTECTIVE, LH CORNER
MAINTENANCE
WARNING
DO NOT HOSE DOWN UNIT AS IT CONTAINS ELECTRICAL COMPONENTS.
STAINLESS STEEL:
All stainless steel body parts should be wiped regularly with hot soapy water during the


scrape stainless steel to remove encrusted materials, soak in hot water to loosen the mate-


ENAMELED ROUND HOTPLATE SURFACE:

any abrasive and avoid excessive or harsh rubbing when cleaning which can cause dam-

CAUTION: DO NOT allow metal, cast iron, or brass polish/cleaners to come in contact with



6