MARS COMMERCE GSW2 EXIO Instruction manual

GSW2 EXIO ANPR
(Automatic Number Plate
Recognition)

ANPR
QUICK CONNECTION MANUAL
Page 2
Version: ANPR Camera Settings_2504_2019_2
Content
1INTRODUCTION...................................................................................................................................................3
2ANPR CAMERA CONNECTION ON THE GSW2 EXIO.................................................................................4
2.1 POWER SUPPLY TO THE GSW2 EXIO.............................................................................................................................4
2.2 POWER SUPPLY TO THE ANPR CAMERA.....................................................................................................................4
3WIEGAND CONNECTION ..................................................................................................................................5
3.1 GSW2 EXIO WIEGAND INPUT ........................................................................................................................................5
3.2 ANPR CAMERA WIEGAND OUTPUT.............................................................................................................................5
4ANPR CAMERA SETTINGS................................................................................................................................6
4.1 APNR CAMERA IP ADDRESS..........................................................................................................................................6
4.2 ANPR CAMERA DEFAULT USER AN PASSWORD.......................................................................................................7
4.3 ANPR CAMERA READIN AREA SETTING.....................................................................................................................7
5LICENSE PLATE NUMBER................................................................................................................................8
5.1 PROGRAMMING THE LICENSE PLATE NO.................................................................................................................................8
6CONTACT DETAILS ............................................................................................................................................9

ANPR
QUICK CONNECTION MANUAL
Page 3
1INTRODUCTION
With this document, we'd like to provide a detail description of the Hivision ANPR camera to the
GSW2 Exio controller. We are using the DS-2CDA26FWD-IZSWG/P camera but note that this
camera has special custom Firmware so the standard camera is not compatible with our controller.
Our system makes it possible to use the camera on the same way as RFID reader/Keypad and it is
connected to the GSW2 Exio Controller over the Wiegand Input, therefore the LAN connection and
expensive computers with Software are not necessary.

ANPR
QUICK CONNECTION MANUAL
Page 4
2ANPR CAMERA CONNECTION ON THE GSW2 EXIO
We need to connect the 15V DC power supply from the AC/DC converter and Wiegand connection.
Connect the ANPR camera and the GSW2 Exio from the same Power Supply unit.
2.1 POWER SUPPLY TO THE GSW2 EXIO
Connect the +15V and GND from the Power Supply to the GSW2 Exio terminals »POWER
SUPPLY«. (Figure 1)
Figure 1
2.2 POWER SUPPLY TO THE ANPR CAMERA
Connect the +15V DC and GND from the same power source (Figure 1) to the Power
camera terminals (Figure 2).
Figure 2

ANPR
QUICK CONNECTION MANUAL
Page 5
3WIEGAND CONNECTION
The GSW2 Exio and ANPR camera are connected via Wiegand Input/Output and fort his
connection only 3 wires are required.
3.1 GSW2 EXIO WIEGAND INPUT
Connect the Wiegand cable with 6 pins connector to the GSW2 Exio Wiegand Input (Figure 3).
Figure 3
3.2 ANPR CAMERA WIEGAND OUTPUT
Connect D0, D1, and GND from the GSW2 Exio Wiegand Input to the ANPR camera Wiegand
Output (Figure 4).
Figure 4

ANPR
QUICK CONNECTION MANUAL
Page 6
4ANPR CAMERA SETTINGS
The ANPR camera is pre-set already in our company. During the installation, we need to set the
License Plate reading area only. Fort his operation the camera must be connected on the PC LAN
connector over the LAN cross cable or via a LAN switch.
After the reading area setting, we can remove the LAN cable connection and it is not necessary for
the APNR camera normal operation.
4.1 APNR CAMERA IP ADDRESS
To get the current ANPR camera IP address we have to run the SADP Tool program which you can
get here:
https://www.hikvision.com/en/Support/Downloads/Tools
After the SAPD Tool running, you will find the camera IP address here (Figure 5):
Figure 5

ANPR
QUICK CONNECTION MANUAL
Page 7
4.2 ANPR CAMERA DEFAULT USER AN PASSWORD
To enter into the camera settings please use the following default settings:
USER NAME: admin
PASSWORD: mars1234
4.3 ANPR CAMERA READIN AREA SETTING
Open the Internet Explorer browser and type the IP address founded by SADP Tool (Figure 5).
Figure 5
For detail settings please check the Hikvision ANPR camera manual.

ANPR
QUICK CONNECTION MANUAL
Page 8
5License PLATE NUMBER
To program the Licence Plate Numbers go to the following link and make a registration. The details
registration and programming procedure please read the GSW2 Exio manual.
EASY SET:
www.easyset.eu
5.1 PROGRAMMING THE LICENSE PLATE NO.
Open Tab Video Pin Access and write the license plate number into the PIN field (Figure 6):
Figure 6

ANPR
QUICK CONNECTION MANUAL
Page 9
6CONTACT DETAILS
MARS COMMERCE d.o.o.
MIRKA VADNOVA 19
4000 KRANJ
SLOVENIA
TEL: + 386 4 280 74 00
E-MAIL: [email protected]
WEB SITE: www.mars-commerce.com
SALES:
E-MAIL: [email protected]
TEL: [phone]