Marshalltown VP3800 User manual

VIBRATORY PLATE COMPACTOR
Part# VP3800 | EDI# 28693
Part# VP3800W | EDI# 29542
104 S. 8th Ave. | Marshalltown, IA
Phone [phone] | Fax [phone]
www.MARSHALLTOWN.com
WS2732revB

2 of 31 104 S. 8th Ave. Marshalltown, IA Phone [phone] • Fax [phone] www.MARSHALLTOWN.com WS2732revB
INTRODUCTION
Congratulations on your purchase of a MARSHALLTOWN vibratory plate compactor. MARSHALLTOWN prides
itself in producing the highest quality construction tools and equipment for the professional and has applied the
same research, design, and production principles to these plate compactors.
These powerful machines are designed for compacting granular fill materials and asphalt. The VP3800 is a leader
in its class in both centrifugal force and operation speed. With 3,800 pounds of centrifugal force you can expect a
well-compacted base while traveling at over 100 feet per minute.
The VP3800W can be used in all applications but it’s water tank feature is necessary for keeping material from
sticking to the bottom of the plate during asphalt paving and patching. Its water tank can be filled on the machine
or easily removed and replaced to fill at a water source.
Your MARSHALLTOWN plate compactor has a first of its kind foldable handle that locks into place during transport
and while moving around the job site. A lifting loop built into the frame allows for lifting strap or forklift access for
job site placement
This machine was built with user safety in mind, however, it can present hazards if improperly operated and
serviced. Carefully read and follow all safety and operating instructions in this manual. Ensure every operator
reads this manual before operating the unit. The replacement of any part with anything other than the
manufacturer’s authorized replacement part may adversely affect the performance, durability, and safety of
the product. Be sure safety precautions are observed. Read and follow all safety and operating instructions in
this operator’s manual. The manufacturer reserves the right to make changes on or add improvements to its
product at any time without prior notice or obligation. The manufacturer reserves the right to decide, upon its sole
discretion and at any time, to discontinue this product. Information regarding operation and maintenance of the
engine can be found in a separate engine manual supplied with this plate compactor. The engine manual provides
all the information required regarding engine adjustments, operation and maintenance. Should any questions arise
concerning engine operation or service, contact the nearest engine repair facility or the engine manufacturer. This
manual covers all MARSHALLTOWN plate compactors and options. For technical questions or repair parts, please
call MARSHALLTOWN customer service at 1-800-888-0127, 641-753-6341 or visit www.MARSHALLTOWN.com.
TABLE OF CONTENTS
Introduction..................................................................................................................................................................................2
Safety Precautions......................................................................................................................................................................3
Safety Decals ...............................................................................................................................................................................4
Warranty........................................................................................................................................................................................4
Specifications ..............................................................................................................................................................................5
Technical Data - Engine..............................................................................................................................................................6
Suggested Retail Parts...............................................................................................................................................................6
Common Components...............................................................................................................................................................7
Pre-Operation Checks................................................................................................................................................................8
Controls and Accessories..........................................................................................................................................................9
Operation ....................................................................................................................................................................................10
Maintenance......................................................................................................................................................................... 10-11
Parts Breakdown.................................................................................................................................................................12-25
Water Tank Option.............................................................................................................................................................. 26-29
Troubleshooting........................................................................................................................................................................30

3 of 31
104 S. 8th Ave. Marshalltown, IA Phone [phone] • Fax [phone] www.MARSHALLTOWN.comWS2732revB
SAFETY PRECAUTIONS
WARNING safety signs are located near specific hazards.
General precautions are listed on CAUTION safety signs.
This notation appears before warnings in the text. It means that the step that follows must be carried out to avoid
the possibility of personal injury or death. These warnings are intended to help the technician avoid any potential
hazards encountered in the normal service procedures. We strongly recommend that the reader takes advantage of the
information provided to prevent personal injury or injury to others.
THE FOLLOWING PRECAUTIONS ARE SUGGESTED TO HELP PREVENT ACCIDENTS. A CAREFUL OPERATOR IS THE
BEST OPERATOR. MOST ACCIDENTS CAN BE AVOIDED BY OBSERVING CERTAIN PRECAUTIONS. READ AND TAKE THE
FOLLOWING PRECAUTIONS BEFORE OPERATING THIS EQUIPMENT TO HELP PREVENT ACCIDENTS. EQUIPMENT
SHOULD BE OPERATED ONLY BY THOSE WHO ARE RESPONSIBLE AND INSTRUCTED TO DO SO.
CALIFORNIA PROPOSITION 65 WARNING: Operation of this equipment and/or engine exhaust from this product
contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.
• Read all operating and maintenance instructions before operating or servicing the machine.
• Equipment is only as safe as its operator. Give complete and undivided attention to the operation of the equipment.
• Keep inexperienced and unauthorized people away from equipment at all times.
• Know how to stop the equipment instantly.
• Test all safety switches before every use.
• Always have all guards and safety devices attached and in place before operating equipment.
NEVER operate the plate compactor with the belt guard cover off.
NEVER let go of the plate compactor or walk away from it while it is running.
• Always make sure engine RPM’s are low and clutch is not engaged when idling engine during warm up.
• Always make sure engine is stopped with the switch in the “OFF” position before making any adjustments or putting
hands or tools near the plate compactor.
• Always make sure engine is in “OFF” position when servicing or not in use.
• Keep the plate compactor in good condition. Loose or damaged parts are dangerous.
• Avoid loose clothing that could get caught in moving parts.
Keep hands and feet away from moving parts.
• Always allow ample time for the plate compactor to cool before making any adjustments.
• Do not smoke while refueling the engine. Ensure the engine is in the “off” position and allow it to cool before refueling.
• Do not spill fuel.
• NEVER operate the plate compactor in confined areas without ample ventilation.
• Keep all warning, caution and safety instruction labels in good condition. Replace missing, damaged or illegible labels.
• DO NOT OPERATE this plate compactor under the influence of alcohol or while taking medication that impairs
your reactions.
• Never sit or ride on the plate compactor.
• Always properly secure machine before transporting.
• Always follow recommended maintenance schedules.
• Use factory authorized parts for replacement.
• Never try to lift unit by yourself.
• Wear safety glasses and hearing protection while operating the plate compactor.
• Wear proper protective clothing while operating plate compactor, including eye, ear, and clothing.
• Clear the work area around the machine to prevent tripping or falling onto the plate compactor.
• Do not operate the plate compactor on extreme inclines.
WARNING!
CAUTION!
CAUTION!
CAUTION!
WARNING!
CAUTION!
CAUTION!

4 of 31 104 S. 8th Ave. Marshalltown, IA Phone [phone] • Fax [phone] www.MARSHALLTOWN.com WS2732revB
SAFETY DECALS
If your safety decals are damaged, they can be replaced by contacting Customer Service.
Do not operate without all guards in place
Never operate machine if parts are damaged
Do not operate prior to reading
Plate Compactor Manual
Stay away from engine, belts, and
other moving parts
WS2844
To avoid pinch points, make sure engine
is stopped and in the “off” position before
making adjustments
Avoid contacting the engine, vibration plate,
and frame after use as surfaces may be hot
Never let go of or walk away from
machine while it’s running
WARNING
VP3800
VP3800W
WS2844
 YEAR PLATE COMPACTOR WARRANTY
This product is warranted to the original purchaser only to be free of defects in material and workmanship,
under normal use and servicing, for a period of 3 years from the purchase date, excluding the engine. Warranty
on the engine is limited to the warranty extended by the engine manufacturer and any warranty claims related to
the engine should be directed to the engine manufacturer. MARSHALLTOWN Company’s sole obligation under
this warranty is limited to the replacement or repair of the product or covered part(s) at no charge delivered
to you F.O.B standard ground rates from its designated facility if the product is determined upon inspection by
MARSHALLTOWN Company to have been defective in materials or workmanship. MARSHALLTOWN Company’s
warranty for replacement parts will extend for the duration of the original product warranty.
This warranty will not apply when the product becomes damaged or inoperative due to misuse, abuse, normal
wear and tear, neglect, improper maintenance, accident, or freight damage; if the product has not been
operated and maintained in accordance with the instructions furnished in the Operator’s Manual; or when the
product has been altered or modified without approval from MARSHALLTOWN Company.
Under no circumstances shall MARSHALLTOWN Company be responsible or liable for any consequential,
special, or punitive damages, pickup and delivery of the unit, inbound shipping charges to MARSHALLTOWN
Company’s service facility, rental charges for a replacement unit, loss of income, or other loss resulting from the
failure of the product to function properly because of a defect in material or workmanship covered under this
warranty.
There are no warranties which extend beyond the description of this warranty. No employee or agent of
MARSHALLTOWN Company has the authority to modify this warranty.
If you wish to make a warranty claim, contact Customer Service at 1-800-888-0127 for return authorization and
instructions.
THE FOREGOING LIMITED WARRANTIES ARE EXCLUSIVE AND ARE GIVEN AND ACCEPTED IN LIEU OF
ANY AND ALL OTHER WARRANTIES EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND ALL OTHER
REMEDIES. MARSHALLTOWN COMPANY’S TOTAL LIABILITY ARISING OUT OF SUPPLYING AND THE USE OF
THE EQUIPMENT, WHETHER BASED ON A CLAIM OF WARRANTY, NEGLIGENCE, OR OTHERWISE, SHALL NOT
EXCEED THE COST PAID BY YOU FOR THE EQUIPMENT.
WS2898WS2853
WS2843
WS2842
WS2845

5 of 31
104 S. 8th Ave. Marshalltown, IA Phone [phone] • Fax [phone] www.MARSHALLTOWN.comWS2732revB
SPECIFICATIONS
CENTRIFUGAL FORCE  LB  KG
VIBRATION FREQUENCY  VPM  HZ
TRAVELING SPEED  FTMIN  MMIN
PLATE SIZE L X W ."X ."  X MM
MAX. AREA OF COMPACTION , SQ FTHR  SQ MHR
OPERATING WEIGHT  LB  KG
WATER TANK CAPACITY  GAL . L
LUBRICATING OIL IN EXCITER CASE . OZ CC OF FULL SYNTHETIC W-
22/"
(561mm)
24/" (632mm)
28/" (735mm)
48/" (1221mm)
35/"
(894mm)
18/" (480mm)

6 of 31 104 S. 8th Ave. Marshalltown, IA Phone [phone] • Fax [phone] www.MARSHALLTOWN.com WS2732revB
SUGGESTED RETAIL PARTS
EDI NAME
32359 V-BELT, AX31 TRI-POWER
 THROTTLE LEVER/CABLE KIT
 OPERATING HANDLE KIT
 RETRACTABLE HANDLE LOCK KIT
 HANDLE BUSHING/CONNECTION KIT
 VIBRATION ISOLATOR KIT
 LIFT HANDLE KIT
 DRIVEN PULLEY KIT
 CLUTCH KIT
 BELT GUARD KIT
32352 THROTTLE CLIPS
32362 WATER TANK KIT
32363 WATER TANK
32364 WATER LINE
32365 END CAP (CLOSED)
32366 END CAP (OPEN)
TECHNICAL DATA - ENGINE
HONDA GX160
WEIGHT LBS 33
DISPLACEMENT CM^ 163
OIL CAPACITY US QT 0.61
FUEL TANK CAPACITY US GAL. 0.82
FUEL  OCTANE OR HIGHER
IDLE SPEED RPM 1400
TOP SPEED RPM 3800
SPARK PLUG BPR6ES (NGK)
SPARK PLUG GAP .7 to .8 mm
ENGINE OIL SAE 10W30
EXCITER OIL . OZ FULL SYNTHETIC W-

7 of 31
104 S. 8th Ave. Marshalltown, IA Phone [phone] • Fax [phone] www.MARSHALLTOWN.comWS2732revB
COMMON COMPONENTS
REF # NAME REF # NAME
1 HANDLE 9 WATER TANK (if applicable)
2 THROTTLE LEVER 10 WATER TANK STRAP (if applicable)
3 THROTTLE CABLE 11 WATER VALVE (if applicable)
4 HANDLE LOCKS 12 DRIP BAR (if applicable)
5 GAS TANK 13 BASE PLATE
6 FUEL VALVE LEVER AND CHOKE 14 LIFTING LOOP
7 ON/OFF SWITCH 15 BEARING HOUSING
8 AIR FILTER 16 ENGINE MOUNTING NUTS
1
2
3
4
4
8
5
5
9
10
11
12
12
13
15
7
6
15
15
14
14
9
10
16
16

8 of 31 104 S. 8th Ave. Marshalltown, IA Phone [phone] • Fax [phone] www.MARSHALLTOWN.com WS2732revB
PRE-OPERATION CHECKS
After removing plate compactor from pallet and packaging, there is no assembly.
The operator must be familiar with the location and operation of all controls. In a safe and well-ventilated area
preform the following:
1. Check entire machine for loose or missing hardware. Contact MARSHALLTOWN Customer Service
at 800-888-0127 if any pieces are missing.
2. Check the fuel filter and inspect air filter.
3. The plate compactor comes filled with exciter oil, so there is no need to check oil level. See Scheduled
Maintenance for oil replacement schedule (page 11).
5. The plate compactor ships with engine oil, but
check prior to starting.
4. The throttle cable/lever comes connected to the handle (A) and carburetor (B). Move throttle lever and watch
movement on the carburetor to insure correct operation.
6. Correct belt tension can be checked by using
moderate pressure to squeeze both sides of belt.
Approximately 1" of movement is correct tension.
Loosen engine mounting plate and adjust to
correct belt tension. Retighten.
A
B

9 of 31
104 S. 8th Ave. Marshalltown, IA Phone [phone] • Fax [phone] www.MARSHALLTOWN.comWS2732revB
CONTROLS AND ACCESSORIES
Handle lock (C) – The handle can lock into place during storage and transport. Always unlock handle into
operating position when in use.
Throttle lever – When starting compactor, position the throttle lever towards front of unit (D). Idle in this
position during warm up.
Adjust throttle lever away from front (E) of unit to engage clutch and operate plate compactor.
C
Throttle in idle position
during warm-up
Pull back to increase throttle
during use
D E

10 of 31 104 S. 8th Ave. Marshalltown, IA Phone [phone] • Fax [phone] www.MARSHALLTOWN.com WS2732revB
OPERATION
STARTING THE ENGINE
1. On a cold engine, move choke lever to CLOSED
position. To restart a warm engine leave choke in
OPEN .
2. Switch the On/Off Switch to the On position.
3. Switch the fuel valve lever on.
4. Pull the starter grip lightly until you feel
resistance, then pull briskly. Repeat until engine
starts.
5. If the choke lever was moved to the CLOSED
position to start the engine, gradually move it to
the OPEN position as the engine warms up.
RESTARTING THE ENGINE
1. Leave the choke lever in the OPEN position.
2. Switch the On/Off Switch to the On position.
3. Switch the fuel valve lever on.
4. Pull the starter grip lightly until you feel
resistance, then pull briskly. Repeat until engine
starts.
MAINTENANCE
CHECK OIL LEVEL BEFORE EACH USE
CHANGE ENGINE OIL FIRST MONTH OR  HRS. -  MO. OR  HRS AFTER
CHANGE EXCITER OIL EVERY  HOURS OR EVERY  YEARS
CHECK FUEL LEVEL BEFORE EACH USE
CHECK AIR FILTER BEFORE EACH USE
CHECK BELT EVERY  HOURS OR EVERY  MONTHS
CHANGE BELT AS NEEDED
CHECK THROTTLE BEFORE EACH USE
REPLACE AIR FILTER EVERY  HOURS OR EVERY  MONTHS
SPARK PLUG - CHECK AND ADJUST EVERY  HOURS OR  YEAR
SPARK PLUG - REPLACE EVERY  HOURS OR  YEARS
CHECK NUTS AND BOLTS BEFORE EACH USE
Choke Lever
On/Off Switch
Fuel Valve Lever

11 of 31
104 S. 8th Ave. Marshalltown, IA Phone [phone] • Fax [phone] www.MARSHALLTOWN.comWS2732revB
MAINTENANCE
CHANGING THE BELT
1. Remove 4 hex head screws (F) holding blade guard in place.
2. Loosen 4 engine mounting plate nuts (G).
3. Slide engine and mounting plate forward so belt can be removed.
4. Install new belt.
5. EVENLY pull mounting plate back to tighten belt on pulleys.
Approximately 1" amount of slack in the belt is acceptable.
6. Tighten mounting plate nuts.
7. Replace belt guard.
CHANGING EXCITER OIL
1. When changing the exciter oil, remove the drain plug located
at the bottom-right of the exciter housing (H), and simply tip the
compactor to drain the oil. Note that the oil will drain more easily
while it is hot. Remember to use only Fully Synthetic 10W30
motor oil when replacing exciter oil.
PLATE COMPACTOR STORAGE
For storage of the plate compactor for over 30 days,
the following is required:
1. Drain the fuel tank completely or add STA-BIL to the fuel.
2. Run the engine until the fuel is completely consumed.
3. Completely drain the oil from the engine crankcase and follow
procedures described in the HONDA engine Owner’s Manual
for engine storage.
4. Completely drain the compactor’s hydraulic oil from the
vibrating case.
5. Clean entire plate compactor, especially the bottom plate,
removing all dirt and foreign matter.
6. Cover plate compactor and engine with plastic covering or
equivalent and store in a clean, dry place.
F
F
F
F
G
H
G

12 of 31 104 S. 8th Ave. Marshalltown, IA Phone [phone] • Fax [phone] www.MARSHALLTOWN.com WS2732revB
PARTS BREAKDOWN - VP
1
14
17
2
3
4
5
7
68
10
14
12
13
10
11
15
16
17
17
16
15
19
18
14
17
14
20
21
15
11
9
9
14
23
6
22
24
6
24

13 of 31
104 S. 8th Ave. Marshalltown, IA Phone [phone] • Fax [phone] www.MARSHALLTOWN.comWS2732revB
PARTS BREAKDOWN - VP
REF # NAME PART # QTY
1 BASE PLATE ASSEMBLY R3929 1
2 MOTOR ADJUSTMENT ASSEMBLY R3932 1
3 FRAME ASSEMBLY R3933 1
4 HANDLE ASSEMBLY R3934 1
5 THROTTLE LEVER-FRICTION STYLE WITH CABLE WX2623 1
6 NYLOK LOCKNUT, 10-24 WR370 3
7 SINGLE CONDUIT SNAP CLIP WR1468 1
8 LOOSE STRING-ON CLIP WR1469 1
9 HEX HEAD CAP SCREW, 5/16-18 UNC, 2.75" LONG WR1502 2
10 HANDLE BUMPER R5875 2
11 HEX HEAD CAP SCREW, 1/2-13 UNC, 3" LONG WR1459 2
12 LOCKING NYLON NUT, 1/2"-13 WR1133 2
13 HANDLE, MOUNT PLATE WX2817 2
14 NYLOK LOCKNUT, 5/16-18 WR118 9
15 HEX HEAD CAP SCREW 5/16"-18 X 1/2" LONG WR1458 4
16 LOCKWASHER, 5/16 INCH, REGULAR WR364 4
17 WASHER FLAT, 5/16 WR236 8
18 BELT GUARD WL712 1
19 A-SECTION, V-BELT, AX-31 TRI-POWER WK227 1
20 HEX HEAD CAP SCREW 5/16" - 18 UNC, 2" LONG WR1396 2
21 HEX HEAD CAP SCREW 5/16-18 UNC, 1" LONG WR1007 1
22 NYLON SPACER - 1/2" OD X 3/16" LONG, #10 SCREW SIZE WL898 1
23 BUTTON HEAD CAP SCREW - 10-24 X 1.5" LONG WR1495 1
24 BUTTON HEAD CAP SCREW - 10-24 X 1.25" LONG WR1498 2

14 of 31 104 S. 8th Ave. Marshalltown, IA Phone [phone] • Fax [phone] www.MARSHALLTOWN.com WS2732revB
PARTS BREAKDOWN - BASE PLATE
QTY.PART #
NAME
REF #
1PD6225
BASE PLATE, MACHINED
1
1WX2461-IR
CYLINDRICAL ROLLER BEARING (INNER RACE)
2
1WX2461
CYLINDRICAL ROLLER BEARING (OUTER RACE)
3
2WK224
BUNA N O-RING, DASH 240
4
1R4424-010
END CAP, MACHINED (CLOSED)
5
1R4423-010
END CAP, MACHINED (OPEN)
6
1WX2460
SPHERICAL ROLLER BEARING
7
1WR1417
STEEL MACHINE KEY 0.25 X 0.25 X 0.75
8
1PB6232
EXCITER SHAFT, MACHINED
9
10WR1007
SCREW HEX HD 5_16-18X1
10
6WR364
Regular Helical Spring Lock Washers(Inch Series)
11
1WR1398
HHCS 1/2"-13 UNC X 0.875"
12
1WR411
WASHER-1/2" ZINC PLATED
13
1WB125
CAST IRON PULLEY
14
1R4524
Steel Spacer 0.280”Long-VP3800
15
1WX2463
RADIAL SHAFT SEAL
16
8WR256
LOCKWASHER, 1/2" ZINC PLATED SPLIT
18
2R4516
HANDLE, LIFT SIDE
19
4WK222
VIBRATION DAMPING SANDWICH MOUNT
20
4WR1455
HHCS 1/2"-13 unc X 0.75"
21
1R4517
MOTOR ISOLATOR PLATE
22
1
WS229MODEL/SERIAL PLATE
23
4WR1462
1/8" POP RIVET
24
1WR1405
NPT PIPE PLUG
25
4WR1018
HCS 1/2-13 X 1-1/2 Z5
26
THIS PRINT DISCLOSES SUBJECT MATTER IN WHICH MARSHALLTOWN COMPANY HAS PROPRIETARY RIGHTS. THE RECEIPT OR
POSSESSION OF THIS PRINT DOES NOT CONFER, TRANSFER OR LICENSE THE USE OF THE DESIGN OR TECHNICAL INFORMATION SHOWN
HEREIN. REPRODUCTION OF THIS PRINT OR ANY INFORMATION CONTAINED HEREIN OR MANUFACTURE OF ANY ARTICLE HEREFROM,
FOR DISCLOSURE TO OTHERS, IS FORBIDDEN, EXCEPT BY SPECIAL WRITTEN PERMISSION FROM MARSHALLTOWN COMPANY.
HEAT-TREAT
MATERIAL
APVD.
BY
DATE
CK.
BY
DWN.
BY
DATE DATE
REV.
DRAWING NO.
OF
NO.
PART
MACH. NO.
FIXT. NO.NO.
E.D.I. SCALE
DIE NO.
GA. NO.
SHEET
TITLE:
REV. REVISION DESCRIPTION DATE APVD
#
C
UNLESS OTHERWISE SPECIFIED:
ALL DIMENSIONS ARE IN INCHES [MILLIMETERS]
GENERAL UNSPECIFIED TOLERANCES
SUPPLIER VERIFICATION IS
REQUIRED PRIOR TO APPROVAL
CRITICAL DIMENSION / NOTE
FRACTION:
.5
ANGLE: 1/32
°
XXXX
XX
XXX
.020
DECIMAL: in. [mm]
.010
.005
.0005
- [.5]
X
-
[.013]
[.12]
[.25]
X
1:3
R3929 -
1 1
BASE PLATE ASSEMBLY
brian.lea
2/17/2021
C:\VaultLocal\Public\ARWorkingDirectory\BML\PlateCompactor\R3929.idw
V15
1
22
2
4
5
10
25
19
20
23
10
10
18
19
20
20
13
12
14
10 11
15
10
11
16 6
4
7
8
9
3
21
18
18
21
11
24
18
26
26
REF # NAME PART # QTY
1 BASE PLATE, MACHINED R4515 1
2 CYLINDRICAL ROLLER BEARING (INNER RACE) WX2461-IR 1
3 CYLINDRICAL ROLLER BEARING OUTER RACE WX2461 1
4 BUNA N O-RING, DASH 240 WK224 2
5 END CAP, MACHINED (CLOSED) R4424-010 1
6 END CAP, MACHINED (OPEN) R4423-010 1
7 SPHERICAL ROLLER BEARING WX2460 1
8 STEEL MACHINE KEY 0.25 X 0.25 X 0.75 WR1417 1
9 EXCITER SHAFT, MACHINED R4438 1
10 SCREW HEX HD 5/16-18 X 1 WR1007 10

15 of 31
104 S. 8th Ave. Marshalltown, IA Phone [phone] • Fax [phone] www.MARSHALLTOWN.comWS2732revB
REF # NAME PART # QTY
11 REGULAR HELICAL SPRING LOCK WASHERS (INCH SERIES) WR364 6
12 HHCS 1/2"-13 UNC X 0.875" WR1398 1
13 WASHER - 1/2" ZINC PLATED WR411 1
14 CAST IRON PULLEY WB125 1
15 STEEL SPACER 0.280" LONG-VP3800 R4524 1
16 RADIAL SHAFT SEAL WX2463 1
18 LOCKWASHER, 1/2" ZINC PLATED SPLIT WR256 8
19 HANDLE, LOWER GRAB R4516 2
20 VIBRATION DAMPING SANDWICH MOUNT WK222 4
21 HHCS 1/2"-13 UNC X 0.75" WR1455 4
22 MOTOR ISOLATOR PLATE R4517 1
23 MODEL/SERIAL PLATE WS229 1
24 1/8" POP RIVET WR1462 4
25 NPT PIPE PLUG WR1405 1
26 HCS 1/2-13 X 1-1/2 Z5 WR1018 4
PARTS BREAKDOWN - BASE PLATE CONT.

16 of 31 104 S. 8th Ave. Marshalltown, IA Phone [phone] • Fax [phone] www.MARSHALLTOWN.com WS2732revB
PARTS BREAKDOWN - MOTOR ADJUSTMENT
REF # NAME PART # QTY
1 ENGINE, HONDA GX160 WX2301 1
2 MOTOR MOUNT ADJUSTMENT PLATE R4518 1
3 HONDA GX EXHAUST DEFLECTOR WX2465 1
4 PAN HEAD SCREW M4 X 5MM WR1507 2
5 STEEL SPACER 0.425" LONG-CP3800 R4535 1
6 CLUTCH ASSEMBLY WX2528 1
7 HHCS, 5/16-24 UNF, 1.25" LONG WR1419 1
8 WASHER, ANSI B WIDE 5/16" WR1418 1
9 NYLOK LOCKNUT, 5/16-18 WR118 4
10 HHCS, 5/16-18 UNC, 1.5" LONG WR1008 4
2
1
6
5
3
4
8
7
9
9
10
2
10

17 of 31
104 S. 8th Ave. Marshalltown, IA Phone [phone] • Fax [phone] www.MARSHALLTOWN.comWS2732revB
PARTS BREAKDOWN - FRAME
REF # NAME PART # QTY
1 FRAME R4519 1
2 BELT GUARD MOUNT PLATE R4520 1
3 ZINC-PLATED STEEL SQUARE NECK CARRIAGE BOLT WR1404 2
4 NYLOK LOCKNUT, 5/16-18 WR118 2
5 LIGHT DUTY DRY-RUNNING SLEEVE BEARING R4521 2
6 OIL-EMBEDDED SLEEVE BEARING WX2563 2
1
6
5
5
6
3
2
4

18 of 31 104 S. 8th Ave. Marshalltown, IA Phone [phone] • Fax [phone] www.MARSHALLTOWN.com WS2732revB
PARTS BREAKDOWN - THROTTLE LEVERCABLE
3
5
4
3
7
6
1
7
23
ITEM DESCRIPTION PART # QTY
1 SINGLE CONDUIT SNAP CLIP WR1468 1
2 LOOSE STRING-ON CLIP WR1469 1
3 #10-24 NYLOK NUT, TOP LOCK STYLE WR370 3
4 THROTTLE LEVER-FRICTION STYLE WITH CABLE WX2623 1
5 NYLON SPACER - 1/2" OD X 3/16" LONG, #10 SCREW SIZE WL898 1
6 BUTTON HEAD CAP SCREW - 10-24 X 1.5" LONG WR1495 1
7 BUTTON HEAD CAP SCREW - 10-24 X 1.25" LONG WR1498 2
THROTTLE LEVERCABLE KIT EDI  INCLUDES:

19 of 31
104 S. 8th Ave. Marshalltown, IA Phone [phone] • Fax [phone] www.MARSHALLTOWN.comWS2732revB
PARTS BREAKDOWN - THROTTLE CLIP
ITEM DESCRIPTION PART # QUANTITY
1 SINGLE CONDUIT SNAP CLIP WR1468 1
2 LOOSE STRING-ON CLIP WR1469 1
3 #10-24 NYLOK NUT, TOP LOCK STYLE WR370 1
4 BUTTON HEAD CAP SCREW - 10-24 X 1.25" LONG WR1498 1
THROTTLE CLIP KIT EDI  INCLUDES:

20 of 31 104 S. 8th Ave. Marshalltown, IA Phone [phone] • Fax [phone] www.MARSHALLTOWN.com WS2732revB
PARTS BREAKDOWN - HANDLE
REF # NAME PART # QTY
1 HANDLE-VP3800-PC-BLUE - LC R4543 1
2 HANDLE, MOUNT PLATE-VP3800-PC-BLUE R4523 2
3 HANDLE BUMPER-VP3800 R5875 2
4 OIL-EMBEDDED SLEEVE BEARING WX2563 2
5 LIGHT DUTY DRY-RUNNING SLEEVE BEARING-VP3800 R4521 2
6 NYLOK LOCKNUT, 5/16-18 WR118 2
7 NYLOK LOCKNUT, 1/2-13 WR1133 2
8 HEX HEAD CAP SCREW 1/2-13 UNC, 3" LONG WR1459 2
9 HEX HEAD CAP SCREW 5/16-18 UNC, 2.75" LONG WR1502 2
1
8
4
5
3 9
2
6
7
6
7
2
39
5
4
8
HANDLE KIT EDI  INCLUDES:
REF # NAME PART # QTY
1 RETRACTABLE SPRING PLUNGER WITH L-HANDLE WX2423 2
2 HEX NUT, JAM, 5/8"-11 UNC WR1402 4
3 LOCKWASHER, INCH, REGULAR " WR1420 4
2
3
3
2
1
PARTS BREAKDOWN - HANDLE PIN
HANDLE PIN KIT EDI  INCLUDES: