Martec Kingston MKDC124OB User manual

K in
g ston DC Smart Series Installation GuideThanks for choosing our
K ingston DC Smart Series ceiling fan. We strongly recommend that you read this manual carefully before installation. 
K 
4O 
65  4  O
 z Models Parameters (Fan and LED Light): 
K 
4 
O 
65

4
 O

z

K  4  65  4 Pa List: 
4 E: sales@maecltd.com.au IP: 02 8778 7500 www.martecaustralia.com.au Models Parameters (Fan
O
nly): 
K 
4 
65  4 
4 4
()
 A  (  )()

WARNING ΖQVWDOODWLRQ0867FDUU\RXWE\DTXDOLȴHGDQGOLFHQVHGHOHFWULFLDQ
E: sales@maecltd.com.au IP: 02 8778 7500 www.martecaustralia.com.au IMPORTANT SAFEGUARDS:Means for disconnection must be incorporated in the fixed wiring in accordance with the wiring rules.The replacement of parts of the safety suspension system device shall be performed by the manufacturer, its service agent or suitably qualified persons.The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person.This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.Children should be supervised to ensure that they do not play with the appliance.- the fixing means for attachment to the ceiling such as hooks or other devices shall befixed with a sufficient strength to withstand 4 times the weight of the ceiling fan;- that the mounting of the suspension system shall be performed by the manufacturer, itsservice agent or suitably qualified persons;- that the fan is to be installed so that the blades are more than 2,1m above the floor.WARNING: If unusual oscillating movement is observed, immediately stop using the ceiling fan and contact the manufacturer, its service agent or suitably qualified persons.How to Assemble Fg.1Fg.2
S  b  k 
E  b  k 
W 

How to Install BladesHow to Install Fg.3
E: sales@maecltd.com.au IP: 02 8778 7500 www.martecaustralia.com.au WARNING Installation MUST carry out by a qualified and licensed electrician. Fg.4
1.Remove 11 screws on the motor as illustrated.NB: Ensure all screws are carefully put aside.2.Remove 4 plastic inserts on the motor before installing the blades.
Fg.5Install the blades as illustrated.Install the blades to the motor with screws provided. Tighten screws securely. Repeat this procedure until all blades are installed.N
B: E nsure the blades do not get damaged or bent during the installation process while the fan maybe on the ground this will affect the performance and balance of the fan and this is NOT covered under warranty.

WARNING ΖQVWDOODWLRQ0867FDUU\RXWE\DTXDOLȴHGDQGOLFHQVHGHOHFWULFLDQ
E: sales@maecltd.com.au IP: 02 8778 7500 www.martecaustralia.com.au How to Install Light PlateqInstall the
LE D light kit to the motor with
3 screws as illustrated.Fan and LED Light Model
Fg.6
Place fan into mounting bracket and align ball j oint slot with mounting bracket as illustrated.Fg.9
How to Install

E: sales@maecltd.com.au IP: 02 8778 7500 www.martecaustralia.com.au WARNING Installation MUST carry out by a qualified and licensed electrician. Wire up the receiver with quick connectors and insert intoWire up the receiver with quick connectors and insert into the mounting bracket. Make sure the antenna wire has beenthe mounting bracket. Make sure the antenna wire has been
VDIHO\IROGHGLQVLGHWKHFDQRS\FRYHUEHIRUHȴQDODVVHPEO\VDIHO\IROGHGLQVLGHWKHFDQRS\FRYHUEHIRUHȴQDODVVHPEO\ (DO NOT cut the antenna wire)(DO NOT cut the antenna wire)
Fan Only Model Fan and LED Light Model
Carefully insert and install the receiver into the mounting bracket.Connect all connectors as illustrated.Fg.10 Carefully insert and install the receiver into the mounting bracket.Connect all connectors as illustrated.Impoant RemindersReceiver must be correctly installed in the mounting bracket When the transmitter cannot control the receiver, please check i) has suicient battery in the transmitterii)any existence of similar remote controlled products nearby that cause interferenceReplace battery if getting low as this will affect sensitivity of the transmitter Take the battery out from the transmitter when leaving used for a long time to avoid battery leaks Isolation switch MUST be connected in the lineHow to InstallHow to InstallFg.8
A
Fg.7
A , Tj

WARNING ΖQVWDOODWLRQ0867FDUU\RXWE\DTXDOLȴHGDQGOLFHQVHGHOHFWULFLDQ
E: sales@maecltd.com.au IP: 02 8778 7500 www.martecaustralia.com.au
The installation is finished.
Complete
How to Install
H 
Fan and LED Light Model
Fg.9
Fan Only Model
T 