Martec SATURN MXFSS20W User manual

SATURN Series Installation Guide
We strongly recommend that you read this manual carefully before installation.
Installation MUST carry out by a qualied and licensed electrician.
Models Parameters:-
MXFSS20W 25W Exhaust Fan Square White
Installation Location
NB: This product is for indoor installation only.
• Unit must be installed into a horizontal location, not suitable for wall
mount or raked ceilings
• Check ceiling cavity for hidden beams, structures and concealed
electircal cabling prior to installation
• Unit should not be installed directly above shower or bath cubicles
or in any location where splashed water can contact the unit, or the
switch can be reached and turned on by someone within a bath or
shower
• Position fan in a central location to maximise ventilation to all areas
• Ensure air is ventilated to an outside location (not into roof cavities)
via the use of a duct/grill assembly which is not supplied
• Do not install the exhaust fan within 1m distance from a ceiling or wall
mounted heat source
Wiring Diagram
E: [email protected] | P: 02 8778 7500
www.martecaustralia.com.au
CAPACITY DISCLAIMER
All capacity gures and technical data quoted is
provided by the manufacturer, Capacity gures
are based on the unit free owing (not connected
to ducting). If you are ducting this unit it is advis-
able to keep the duct run as short, straight and
tight as possible.
240MM
Technical Specication
Air Extraction m³/hr 180m³/hr
Power Wattage 25W
Voltage 220-240V 50Hz
Capacity (L/S) ≤89L/S
Materials / Housing Plastics with ABS Fascia
IP Rating IPX4
Cutout Size Dia 240mm
Noise Level (dB) <45dB
Minimum Height 220mm clearance height above the unit
Ducting Size 100mm
Accessories Included 900mm cable with 3 pin plug
230

Accessories
4 x Internal plastic mounting dust covers ( Remove grill as far as safety wire will allow and then t the dust covers over
the 4 internal ceiling mounting points).
100
223
195
150
WARNING Installation MUST carry out by a qualied and licensed electrician.
E: [email protected] | P: 02 8778 7500
www.martecaustralia.com.au
Installation Instructions
NB: Installation MUST carry out by a qualied and licensed electrician.
• Turn OFF mains power
• Ensure Location Instructions (see front page) are followed
• Mark and cut a Ø240mm hole into the ceiling using proper tools such as plaster saw, jig saw or hole saw
NB: Highly recommended to wear safety glasses to avoid fell from the ceiling into the eyes
• If ducting is required for ventilation. Install a 100mm duct pipe to the exhaust fan and lay the ducting across the ceiling
and onto a suitable 100mm exhaust vent (see gure 1)
• Plug the cable into the power point socket in the ceiling (see gure 2)
• Position fan in hole, rotate mounting screws with a screwdriver until slip blocks rmly secure fan onto ceiling plaster.
Do not over-tighten (see gure 3)
• Replace external cover over fan blades by locating spring hole slots and allowing springs to pull the cover plate up over
the fan and onto the ceiling surface
NB: Please ensure yellow label “Tear this seal before using or installing!” is removed from the unit
• Turn ON mains power
Figure 1: Installing ducting (sold separately) Figure 2: Connect the power Figure 3: Fix the fan in place and install cover
2 Year Replacement Warranty
Visit our website for details https://www.martecaustralia.com.au/warranty-statement/
WARNING
• Installation of bathroom heater and exhaust fan MUST follow SAA standards and meet local authority
regulations.
• Installation MUST be carried out by a qualied and licensed electrician.
• Bathroom heater and exhaust fan MUST NOT be installed under any electrical outlet.
• Bathroom heater and exhaust fan MUST NOT be installed near curtains or other combustible materials.
• Joists, beams and rafters MUST NOT be cut or notched to install the product.
• DO NOT attempt to open and repair the product.
• The warranty is VOID if product is not installed according to this installation guide.
CARE & MAINTENANCE
• The product must be turned OFF and cool before cleaning.
• To clean the fascia simply use a dampened cloth.